Product Info
Table Of Contents
- 1. Brief Introduction
- 2. Technical Specifications
- 4. Description of indicator and press-button
- 5. Definition of DB9 Socket Pin
- 6. Description of Power Supply Condition
- 7. Description of Serial Interconnection
- 8. Instructions
- 9. Configuration Tools
- 10. AT command
- 1. Test command
- 2. Set / Inquire the baud rate
- 3. Set / Inquire the serial communication mode
- 4. Set / Inquire authentication password
- 5. Set/Inquire Name
- 6. Set / Inquire Sniff power-saving mode
- 7. Set / Inquire the parameters of inquiring scan and connecting scan
- 8. Set / Inquire whether authenticate
- 9. Set / Inquire device type
- 10. Set / Inquire device role
- 11. Set / Inquire the data processing mode when not connected
- 12. Set / Inquire flow control mode
- 13. Set / Inquire the type of data device
- 14. Set / Inquire whether it is bind
- 15. Set/Inquire the memorized remoted Bluetooth device
- 16. Clear the memorized address
- 17. Inquire local Bluetooth address
- 18. Inquire software version
- 19. Software reset
- 20. Inquire remoted Bluetooth devices
- 21. Cancel inquire remoted Bluetooth devices
- 22. Restore default settings
- 23. Inquire all commands
- 11. FAQ:
- 1 After powering the module, the indicator of the Module doesn’t blink.
- 2 When there are multiple Bluetooth devices around, how to connect to the specified Bluetooth device?
- 3 How to operate if want to connect with multiply devices at the same time？
- 4 How the multipoint connections send and receive data? And what are the differences between the sending & receiving of multipoint and point-to -point connections?
- 5 Can not set the parameters, or use the Configuration Tools displaying "connection timeout" when connects to the PC
- 6 How to send AT command by your hand？
- 7 Two serial adapter can not connect with each other
- 8 Why PC, USB Dongle cannot find the serial adapter?
- 9 Why PC USB Dongle and serial adapter cannot realize data communication or only communicate by one-way data communication?
- 10 How to communicate with PDA?
- 11 How to communicate with Bluetooth mobile phone?
- 12.1 Equipment Type Number
- 12.2 MAJOR SERVICE CLASSES
- 12.3 MAJOR DEVICE CLASSES
- 12.4 THE MINOR DEVICE CLASS FIELD
- 12.5 MINOR DEVICE CLASS FIELD - COMPUTER MAJOR CLASS
- 12.6 MINOR DEVICE CLASS FIELD - PHONE MAJOR CLASS
- 12.7 MINOR DEVICE CLASS FIELD - LAN/NETWORK ACCESS POINT MAJOR CLASS
- 12.8 MINOR DEVICE CLASS FIELD - AUDIO/VIDEO MAJOR CLASS
- 12.9 MINOR DEVICE CLASS FIELD - PERIPHERAL MAJOR CLASS
- 12.10 MINOR DEVICE CLASS FIELD - IMAGING MAJOR CLASS
Chongqing Jinou Science &Technology Development Co., Ltd.
http://www.oemblue.com/ info@oemblue.com
11
Notes: VCC/Nc says when use power sockets power-up, 1 and 9 pin is Nc. Using DB9
power-up, 1 and 9 pin connect VCC power supply.
8. Instructions
After powering on, the power indicator light of the device should bright immediately and
the other indicator light is blinking separately.
After the factory, the default settings for the device are generally 9600bps, 8-N-1 communication mode
and with flow control. It is a slave device and matching code is 1234.
If there is need to modify parameter, please press the switch button to make 100M Wireless
RS232 Serial Adapter enter into parameter setting mode. Then the two blinked state
indicator light extinguished. Setting related parameter through AT command or parameter
setting tools, such as by the following parameter: master/slave device, baud rate,
authentication, and bind address.
If communicate between two 100M Wireless RS232 Serial Adapters, you must set one
adapter as a master device and the other as a slave device. And you can identify the status
according to the blinking state of the master/slave indicator.
Connecting several device need to enter command mode setting and the max memorized
slave device number M (AT+ROLE= M\r\n). After returning data mode, it will
automatically find and connect slave device around.