INSTRUCTION MANUAL SUJKR ?@ >
Table of Contents 1 Important Safety Instructions.......................................................................1 2 Product Components...................................................................................2 2.1 The main machine and accessories.................................................................2 2.2 The main machine......................................................................................3 2.3 Charging station......................................................
1 Important Safety Instructions Please read the following safety instructions before using this product to avoid damage. Warning! Violation of safety instructions may cause severe personal casualty and property loss.
2 Product Components 2.1 The main machine and accessories No. Name Quantity 1 Main machine 1pc 2 Charging station 1pc 3 Remote control 1pc 4 Adapter 1pc 5 Cleaning brush 1pc 6 Insturction manual 1pc 7 Side brush 2pcs 8 Water tank 1pc Attention: Please take actual product shall prevail on the basis of not less than the above accessories.
2 Product Components 2.2 Main machine 1. Signal receiving sensor 2. Clean button 3. Bumper 4. Panel 5. Universal wheel 6. Charging poles 7. Battery cover 8. Stair detection sensor 9. Main brush 10. Dustbin 2.3 Charging station 1.Signal projector 2.Charging poles 3.Indication light 4. Adapter socket 11.Dustbin cover button 12.Charging socket 13. Side brush 14.
2 Product Components 2.4 Dustbin 3.Dusbin upper cover 4. Dusbin botton cover 2.5 Water tank 1. Water tank button 2. Water inlet cap 3. Air valves 4. Mop 2.6 Side brush Please install the side brush according to the color of the socket of the side brush. Left brush is green color, and right brush is red color. 2.7 Remote control 1 The robot is in standby or cleaning mode, press this button to start auto recharging.
2 Product Components 4 Press direction button to adjust the robot moving direction. 5 Press this button for 3 seconds to start time 6 The main machine will start the distribution net work if press the button for a long time which above 3 seconds. 7 Press the botton for 3 seconds for the appointment cleaning, press the On/Off button remind you successful appointment with “Ding”.
3 Product operations 3.1 Quick start guide 1.Place charge Place charger, connect the adapter and power, and the power light on the charger will stay lit. Position the charger against P P the wall, and remove all obstacles about 1 P or 2 meters ahead of the charger. 2. Power Switch Turn on the power switch of the product, and press directly the sweep button on the panel, voice prompts:enter cleaning mode, the product is start to clean.
3 Product operations Attention: 1 When charging, make sure the power switch is on. 2 using the charger stand will interrupt the charging and start the cleaning, so please do not make this operation when using thedirect charge. * + ; 4 When charging, the cleaning button blinks, and when fully charged, the cleaning button stops blinking, and lit permanently. 5 Please switch the main machine off when long time no use. 3.2 Pause/Standby mode 1.
3 Product operations < = * according to “up, down, left and right” direction button. 2 Press the clock button once again to save the setting. 2.Set the pre-scheduled cleaning time 1 Point the remote controller at the machine (the machine is in standby status).
3 Product operations 2.Spot cleaning Place machine in clean area, press the remote button on the machine to start with the placement point spiral sweep. 3.Edge cleaning Press button on remote control to start edge cleaning mode, the robot will start edge cleaning. Note： 1 The current job will be suspended if you press the auto button, whatever in any cleaning mode. Press the auto button again the machine will continue work in the pre-timeout mode.
3 Product operations 5 Put the tank into the machine, start the machine, and water enters into the mop through wool column, water stopped dripping out of the tank when the machine stops. Pour water out if the machine stops working for a long time. Mop 2 Installation of water tank jacks. Attention 1 Please remove the water tank when injecting water, and do not inject with complete machine. 2 Please remove water drops when installation of water tank.
4 Product Maintenances 4.1 Cleaning of side brush Side brush can be removed and clean by water. Please dry them completely before second use. If side brushes damaged, please replace them. Attention: When replace side brush, please pay attention to the L and R position and color. 1 Press PUSH button on dustbin, remove the dustbin. 2 Open dustbin bottom cover. . 4 Pour out trash into trash bin. 6 months. 6 Please install them correctly before second use. Attention 1 Please clean the dustbin after each use.
4 Product Maintenances 4.3 Cleaning of sensors and charging poles 1 Clean sensors and charging poles on robot bottom by using soft cloth. 2 Clean charging poles on charging station by using soft cloth. )NGXMOTM IUTZGIZUX 9KTYUX 9KTYUX )NGXMOTM IUTZGIZUX 4.4 Cleaning of main brush 1 Press the locker, open main brush cover. after cleaning. 3 Clean the hair and dirt by using a cleaning brush. Please make sure that do not lose the rubber. 4 Install the main brush and cover after cleaning.
4 Product Maintenances 4.5 Water tank maintenance The mop needs to be cleaned on time, =GZKX OTRKZ the mop is removed from the water tank and cleaned. Note: If the water tank is not used for a long time, please pour out the water. 3UV 4.6 Battery replacement 1 Open the battery cover by using a screw driver. 2 Hold the insulation cloth and pull out the battery. 3 Detach the battery from the main machine. 4 Install new battery. Make sure the side with words up. 5 Connect the battery with main machine.
5 Resume to Default Setting If the machine has some software system problems during the using ,it can be triggered by the 1 Hold down the host front collision left sensor when the produce is in shutdown state. 2 While hold down the host front collision left sensor ,open the power switch on the bottom ,the host machine lights starts blinking. 3 Until the indicator lights became light on,hold down the host front collision right sensor,at this again and release the left and right sensors.
6 Trouble shooting No. 1 Problems Solution The robot keeps 1 Avoid working in high light intensity environments. moving backwards 2 Avoid working on deep dark carpets. 3 Clean the stair detection sensors by using a soft cloth. 4 Check the bumper and clean. 2 3 The robot do not work 1 Turn on the power switch button. 2 Check the battery capacity, and charge the robot. Check again after full charging.
7 Product Parameters Size 320*320*85mm Net Weight 2.6kg Working voltage 14.8V Input voltage 19V Input current 1.
8 F C C Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
