M Series SETUP GUIDE 020-100011-04
M Series SETUP GUIDE 020-100011-04
NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Table of Contents 1.1 Purchase Record and Service Contacts .......................................................................................1-1 1.1.1 List of Components..............................................................................................................1-1 1.1.2 Key Features ........................................................................................................................1-2 1.1.3 General Precautions .......................................................
Table of Contents 10+ ....................................................................................................................................... 3-6 Help ...................................................................................................................................... 3-6 Menu .................................................................................................................................... 3-6 OSD (On-screen display) ........................................
Table of Contents 5.7.9 Data is Cropped from Edges ................................................................................................5-4 5.7.10 Display Quality Appears to Drift from Good to Bad, Bad to Good .................................5-4 5.7.11 Display has Suddenly Frozen ............................................................................................5-4 5.7.12 Colors in the Display are Inaccurate................................................................................
1 Introduction Every effort has been made to ensure the information in this document is accurate and reliable; however, due to constant research the information in this document is subject to change without notice. 1.1 Purchase Record and Service Contacts Whether the projector is under warranty or the warranty has expired, Christie’s highly trained and extensive factory and dealer service network is always available to quickly diagnose and correct projector malfunctions.
Section 1: Introduction 1.1.
Section 1: Introduction 1.1.3 General Precautions Do NOT look into the lens FIRE HAZARD. Keep hands, clothes and all combustible material away from the concentrated light beam of the projector. Position all cables where they cannot contact hot surfaces or be pulled or tripped over. All installation and maintenance procedures must be performed by a Christie accredited service technician. Projector must be operated in an environment that meets operating specifications, as listed in 6 Specifications. 1.1.
2 Installation and Setup 2.1 Projector Quick Setup and Installation The following instructions are for those preferring a quick setup. Refer to the remaining subsections for detailed setup instructions. Always power down the projector and disconnect all power sources before servicing or cleaning. Refer to Safety Warnings and Guidelines in 4 Maintenance. STEP 1 - Installing a Projection Lens The projection lens, shipped separately from the projector, must be installed prior to setting up the projector.
Section 2: Installation and Setup 2. Align the lens interface plate with the lens mount. Align the lens electrical connector with the mating connector on the lens mount. Fully insert the assembly straight into the lens mount opening without turning. Press using your hand as shown in Figure 2-2. NOTE: When installing the lens, ensure that the lens is not inserted at an angle, as this can cause damage. FIGURE 2-2 LENS PLACEMENT 3. Remove the front lens cap. 4.
Section 2: Installation and Setup FIGURE 2-5 FIGURE 2-6 6. Use a 5mm hex driver to fasten the red security screws provided with the lens mount (Figure 2-5 ), or hand tighten the lens retaining screws attached to the lens (Figure 2-6 ). NOTES: 1) Recommended for heaviest lenses such as 0.73:1 and 1.2:1. 2) The red security screws MUST be installed when hoisting the projector overhead, or installing the projector in an overhead position.
Section 2: Installation and Setup • Video Decoder Input Card, depending on the source you can apply the following; • Composite video source to 1-CVBS, using a BNC Cable NOTE: Same signal can be used on 4, 5 or 6 when input is selected as CVBS. • A component signal on Inputs 4(Pr), 5(Y), 6(Pb) using BNC Connectors. NOTE: Grouped as a component input, YPbPr. • S-Video to one of the two, 2-SVID or 3-SVID using S-Video cable.
Section 2: Installation and Setup 2.2 Detailed Setup and Installation Always power down the projector and disconnect all power sources before servicing or cleaning. Refer to Safety Warnings and Guidelines in 4 Maintenance. Switch the lamp off when the door is opened. The lamp doors are provided with clear windows to indicate when the lamps are on. 2.2.1 Mounting There are several methods for mounting the projector.
Section 2: Installation and Setup 6. Throw Distance: Ensure the projector is positioned in the throw distance range for the particular lens. Folded Optics In rear screen applications where space behind the projector is limited, a mirror may be used to fold the optical path (Figure 2-7). The position of the projector and mirror must be accurately set - if considering this type of installation call your dealer for assistance. FIGURE 2-7 FOLDED OPTICAL PATH 2.2.
Section 2: Installation and Setup 4. Use a 5mm Allen™ key to loosen the 3 locking setscrews on the lens mount (Figure 2-10). NOTE: The setscrews must be backed out several turns, so that they do not contact the inner lens mount plate. FIGURE 2-9 CROSS-HAIR PATTERN FIGURE 2-10 SCREW LOCATIONS 5. Fine tune the focus of cross-hair pattern I by adjusting the appropriate capscrew (Figure 2-10). Adjust until the cross-hair image is in focus with minimal flare. 6.
Section 2: Installation and Setup 11. Lock the setscrews, and re-check the boresight quality. Tighten the setscrew enough to ensure they will not shift. FIGURE 2-11 POSITION SETSCREW FLUSH 2.2.4 Powering Down The projector can be powered down by using one of the following methods: Remote Keypad/Built-In Keypad • Press and hold POWER OR • Press POWER twice OR • Press POWER once, then immediately press the DOWN key.
Section 2: Installation and Setup 2.2.5 Projector Communications Status LEDs Looking from the back of the projector, the LEDs represent, from left to right; Lamp 1, Lamp 2, Power, and Status.
3 Operation This section explains how to operate the projector once it has been setup and installed. Read this section and familiarize yourself with the components ans menu options before using your projector. Refer to Safety Warnings and Guidelines in 4 Maintenance. 3.
Section 3: Operation Remote Keypad FIGURE 3-1 REMOTE KEYPAD 3-2 M Series Setup Guide 020-100011-04 Rev.
Section 3: Operation Wired Remote You can convert the remote keypad into a wired remote keypad using the cable provided with the projector. Connect one end into the remote and the other to the XLR connector on the input panel labeled as wired keypad. The wired remote is recommended when: • The built-in keypad is inaccessible • The lighting conditions are unsuitable for proper IR transmission NOTE: Leave the batteries in the wired remote for the laser pointer key to work.
Section 3: Operation • Auto Key, enabled state when the power is on and there are no test patterns on the screen. If the power is off or a test pattern is displayed the Auto key is disabled. • Exit Key, is determined in the specific context of the screen being displayed. • Input Key, enabled when the power is on. Disabled if the power is off. • Lens Key, enabled when the power is on. Disabled if the power is off. • Shutter Key, enabled when the power is on. Disabled if the power is off.
Section 3: Operation The best auto setup will be obtained under the following conditions: • Input levels, it is best to have an image with saturated (very bright) colors. • Phase, high contrast edges are needed. To determine active window size: • Video images should have whites and blacks in the image. • Wide range video images should have content (including white) that extends to all edges of the image. Channel Select a specific source setup (channel) defined and stored in projector memory.
Section 3: Operation Gamma Determines how gray shades are displayed between minimum input (black) and maximum input (white) for a given amount of signal. The proper setting helps maintain optimized blacks and whites while ensuring a smooth transition for the “in-between” values utilized in grays.
Section 3: Operation Function Key IF WITHIN A NUMERIC FIELD IN A MENU: Use FUNC to enter a negative number. IF WITHIN A TEXT FIELD: Press FUNC followed by the UP ARROW KEY or DOWN ARROW KEY to convert between capital and lower case letters. Press FUNC followed by the LEFT ARROW KEY or RIGHT ARROW KEY to insert or delete a character. Press FUNC followed by ENTER to delete all characters.
Section 3: Operation Lens H and Lens V When adjusting the image for focus, zoom or horizontal and vertical positioning, use the specific arrow keys (LEFT/RIGHT ARROW KEY or UP/DOWN ARROW KEY) related to each function. A small window will appear to indicate the type of adjustment taking place. For example, • • • • Use the FOCUS and the LEFT ARROW or RIGHT ARROW KEY to improve image clarity as desired. Use the ZOOM and the LEFT ARROW or RIGHT ARROW KEY to achieve a desired image size.
Section 3: Operation When finished with a Function menu: • Press EXIT to return to the previous screen. OR • Press MENU to leave the menu system and return to the presentation. NOTES: 1) If there is no signal present, all source-dependent adjustments are disabled. 2) After 15 minutes of inactivity, the projector leaves the menu system and returns to the presentation. 3) The Status menu is read-only. On-line Help Press HELP to display summary information about the current menu or highlighted option.
Section 3: Operation Slide bars in menus – The current value for a given parameter, such as size or vertical stretch, appears to the left of its slide bar icon (adjustment window). This number often expresses a percentage, or it may have units associated with it (such as FIGURE 3-6 EXAMPLE OF SLIDE BAR pixels), depending on the specific option. Press LEFT/RIGHT ARROW KEY to gradually adjust the setting up or down—both the number and the length of the bar change accordingly. Hold for continuous adjustment.
Section 3: Operation Editing Text Activate the Edit Window: To enter or edit text, highlight the desired parameter (such as a channel name) and press ENTER to activate its adjacent edit window. Any previously entered text is displayed with its first character highlighted in a square cursor, signifying that this character is ready for editing. Navigate Within the Edit Window: Press RIGHT ARROW KEY to move the cursor forward or LEFT ARROW KEY to move the cursor backwards as desired.
Section 3: Operation Edit numerical values: Enter numbers directly from the keypad to specify numbers representing projectors channels (source setups), or slots. As each digit is entered, it is inserted on the right of the field, and the numbers already in the field are shifted on the left. The channel numbers are defined with two digits—for example, if you enter only a single digit (such as “7”) for a channel number, the channel will automatically be defined as “07”. Enter “07” to utilize this channel.
4 Maintenance 4.1 Filters 4.1.1 Optional Filters Use only special, high efficiency Christie approved filters. This projector is not equipped with fan finger guards. Keep fingers away from the fan blades when replacing filter. Dust Air Filter CHECK: Monthly Check projector air dust filters, at minimum, every month. Dust air filters (if fitted), should be replaced whenever the lamp is replaced or between 200-500 hours, depending on use.
Section 5: Maintenance Fog Filter Fog filters should be replaced after each use of the projector to a maximum of 20 hours. The life of the filter is approximately 20 hours based on environmental conditions. Leave the filters in their sealed packaging until ready for use. NOTE: The fog filters cannot be re-used or they will clog up with oil and the projector will overheat and shutdown. Replace Filters: 1. Unscrew the 2 captive screws at the top of each filter door (Figure 4-1).
5 Troubleshooting If the projector is not operating properly, note the symptoms and use this section as a guide to resolve the problem. If the problem cannot be resolved. contact your dealer for assistance. NOTE: A Christie accredited service technician is required when opening an enclosure to diagnose any “probable cause”. 5.1 Power 5.1.1 Projector Does Not Power ON 1. Ensure projector is plugged in? Check power switch above power cord is in the ON position. 2. Check that the Status LEDs are ON.
Section 6: Troubleshooting 5.2.3 Flicker, Shadows Or Dimness 1. Check lamp power through the remote keypad checking the Lamp menu or from the web user interface Advanced: Lamp menu. Try increasing lamp power. 2. Replace the lamp. 5.3 LCD 5.3.1 Blank Screen, No Menu Displaying 1. Press any arrow key on the built-in keypad. The backlight on the LCD and the backlight for the built-in keypad should turn on. If the LCD is still blank, restart the projector. 5.4 Remote Keypad 5.4.
Section 6: Troubleshooting 5.6 Ethernet 5.6.1 Trouble Establishing Communication with Projector 1. Ensure any address changes have been saved, and reboot to implement. If you still have trouble establishing communications with a projector added to an existing Ethernet network, the projector’s IP address is likely in conflict with another address already in use. Contact your network administrator. 2. Ensure Ethernet settings are valid for the site.
Section 6: Troubleshooting 5.7.5 The Display is Faint 1. Brightness and/or contrast and/or gamma may be set incorrectly. 2. The source may be double terminated. Ensure the source is terminated only once. 3. The source (if non-video) may need a different sync tip clamp location. 5.7.6 The Upper Portion of the Display is Waving, Tearing or Jittering This can occur with video or VCR sources. Check your source. 5.7.
Section 6: Troubleshooting 5.7.13 Display is Not Rectangular 1. Check leveling of the projector. Ensure the lens surface and screen are parallel to one another. 2. Is the vertical offset correct? Make the necessary adjustments to the vertical offset on the lens mount. 5.7.14 Display is “Noisy” 1. Display adjustment at the input source may be required. Adjust pixel tracking, phase and filter. Noise is particularly common on YPbPr signals from a DVD player. 2. Ensure the video input is terminated (75 ohms).
Section 6: Troubleshooting FIGURE 5-1 5-6 M Series Setup Guide 020-100011-04 Rev.
6 Specifications This section provides detailed M Series features; including inputs, lamp, and power requirements. NOTE: Due to continuing research, detailed features are subject to change without notice. 6.1 Feature Set 6.1.1 Air Filters (Optional) Filter media types Filter access Coarse foam filter Fog filter Service-interchangeable via access panel 6.1.2 Lamps Dual Mercury lamp system 6.
Section 7: Specifications 6.
Section 7: Specifications 6.4.1 Lamp Specification Type Mercury Lamp (Hg) Power 350W HD/350W SX+/350W WU/350W WX 200W HD/200W SX+/200W WU/200W WX DLV Models (HD/SX+) 350W Lamp rated lamp life to 50% brightness (2 hrs on, 15 min. off duty cycle) 200W Lamp rated lamp life to 50% brightness (2 hrs on, 15 min. off duty cycle) Warm-up time (to full output) Operating position 300 W min., 370 W max (software adjustable) 150 W min.
Section 7: Specifications Lens Throw Ratio Throw Ratio Fixed Zoom 6.5 Lens Description Part Number WXGA SXGA+ HD WUXGA Lens ILS 0.73:1SX+/0.67:1HD 118-100110-xx 0.75 0.73 0.67 0.67 Lens ILS 1.2SX+/1.1HD 118-100117-xx 1.23 1.2 1.1 1.1 Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-xx 1.28-1.64 1.25-1.6 1.16-1.49 1.16-1.49 Lens ILS 1.5-2.0SX+/1.4-1.8HD 118-100112-xx 1.54-2.05 1.5-2.0 1.4-1.8 1.4-1.8 Lens ILS 2.0-2.8SX+/1.8-2.6HD 118-100113-xx 2.05-2.87 2.0-2.8 1.8-2.6 1.
Appendix A:GPIO This section explains how to use a GPIO link from the projector to external equipment, such as devices for 3D synchronizing. A.1 GPIO Port The GPIO connector located on the input panel provides a flexible method of interfacing a wide range of external I/ O devices to the projector. There are 7 GPIO pins available on the 9pin D-Sub GPIO connector, which are configurable via RS232 commands (Figure A-1).
Appendix A: GPIO Configuring the GPIO The GPIO connector can be configured to automate any number of events using the serial command code GIO. Each Pin is defined as either an input or output depending on the desired outcome. Configure the pin as an input if you want the projector to respond to something the device does and as an output if you want the external device to respond to an action taken by the projector.
Corporate offices Worldwide offices USA – Cypress ph: 714-236-8610 United Kingdom ph: +44 118 977 8000 Hungary/Eastern Europe ph: +36 (0) 1 47 48 100 Beijing ph: +86 10 6561 0240 Canada – Kitchener ph: 519-744-8005 Germany ph: +49 2161 664540 Singapore ph: +65 6877 8737 Korea ph: +82 2 702 1601 France ph: +33 (0) 1 41 21 44 04 Shanghai ph: +86 21 6278 7708 Japan ph: +81 3 3599 7481 For the most current technical documentation, please visit www.christiedigital.
