TOP MOUNT REFRIGERATOR USER MANUAL MODEL CTM410NW CTM409NBS CTM408NSS CTM407NB Customer Service 1300 796 688 www.chiq.com.
PART NAMES AND LOCATIONS No 1 2 3 4 5 6 7 8 9 10 11 Description Freezer glass shelf Air flow adjustment knob Temp setting knob Fridge glass shelf Crisper cover Crisper Leveling foot Freezer door rack Fridge door upper left rack Fridge door upper right rack Fridge door bottom rack IN ACCESSORY BAG: USER MANUAL, WARRANTY, Door reversal parts(upper hinge and hinge cover) As the manufacturer holds the authority to redesign or modify its products without notice: Any modifications or upgrades of our products
IMPORTANT SAFETY INSTRUCTIONS WARNING Follow these basic precautions to reduce the risk of fire, electrical shock hazards or injury when operating the refrigerator: • This product has been designed for using in a normal domestic environment. It is not intended for commercial use which will avoid warranty, such as supermarket, food shop, pharmacy, commercial kitchen & etc.
R600a WARNINGS NOTE: This model uses R600a flammable refrigerant in its sealed system. The following must be observed for your safety: R600a Refrigerant Warning • This appliance contains 0.052kg R600a refrigerant which is environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the greenhouse effect. • During transportation and installation, ensure that the tubing of the refrigerant circuit is not damaged. • Leaking refrigerant can ignite and may damage the eyes.
Door reversal instruction Door reversal job requests some spare parts which are in the accessory bag, top hinge and hinge cover. The following tool is required, flat screwdriver, phillips screwdriver, adjustable spanner, socket wrench and 8mm socket. 1. Make sure that your refrigerator is unplugged. 2. Remove one screw in the hinge cover, remove hinge cover and three screws, then remove the upper hinge. 3. Remove the freezer compartment door from the cabinet. 4.
9. Install the lower hinge on the left side of the cabinet. 10. Remove the screw that secures the door stops from the bottom right of the refrigerator compartment door, then remove the door stops and install to the bottom left side. 11. Install the refrigerator compartment door. 12. Move the door bushing from the top right side of the refrigerator door to the top left side of the door. And move the left hole cover to the right side. 13.
16. Install the freezer compartment door. 17. Move the door bushing from the top right side of the freezer door to the top left side of the door. And move the left hole cover to the right side. 18. Remove the screw that secures the hinge screw hole cover from the top left side of the cabinet, remove the cover and secures the cover on the top right side of the cabinet. 19. Secure the upper hinge to the top left side of the cabinet with the three screws you removed previously.
INSTALLATION INSTRUCTIONS Before Using the Refrigerator • • • Remove the exterior and interior packing. Before connecting the refrigerator to a power source, let the unit stand upright for approximately 4 hours to mitigate the possibility of a malfunction in the cooling system from improper handling during transportation. Clean the interior surface with warm water using a soft cloth.
OPERATING INSTRUCTIONS START - The temperature inside the refrigerator is controlled by the potentiometer installed in the refrigerated room. The temperature inside the refrigerator varies depending on the opening and closing doors of the refrigerator, the ambient temperature. Refrigerator temperature adjustment 1. When adjusting the temperature knob from the 1 to the 5, the refrigerator temperature gradually gets colder. Please set it on 3 for first one or two days.
Humidity control The crisper has a Humidity control on the front, set it to high will keep more moisture inside and set it to Low position will reduce the moisture. If too much moisture or condensation under the crisper glass cover. Please put leafy greens, like arugula, spinach, and herbs into a plastic or paper bag before putting the crisper.
GENERAL CARE AND MAINTENANCE Cleaning the Refrigerator • Upon installation of your new appliance, it is recommended that it be cleaned thoroughly and properly maintained thereafter. • Turn off the refrigerator and then unplug the unit from the wall outlet. • Remove all food content before washing the inside with a damp cloth soaked in lukewarm water and dishwasher liquid. Don’t use any chemical detergent which might damage the fridge.
TROUBLESHOOTING GUIDE Problem The fridge has no power The light is not working. Solution Power cord isn’t plugged in properly. The circuit breaker tripped or a blown fuse. Try a different power point. There is no light in freezer compartment, only fridge compartment has light. Make sure the power is connected to the unit.
Freezer control incorrectly set. Set back to mid position. Temperature control is set too cold. Turn the control to a warmer setting and allow several hours for the temperature to stabilize. The exterior refrigerator walls can be as much as 15-20 degrees warmer than room temperature. This is normal while the compressor works to transfer heat from inside the refrigerator cabinet to the condenser behind the refrigerator side walls. Popping or cracking sound when compressor comes on.
Customer Service 1300 796 688 www.chiq.com.au c Changhong Electric (Australia) P/L all rights reserved.
