ChipSiP CWFC10x Serial CWF10x Serial AP/Client/Router With 2LANs
ChipSiP CWFC10x Serial Copyright Statement Trademarks Copyright @2010 Contents are subject to change without notice. All trademarks belong to their respective proprietors. Copyright Statement THIS DOCUMENT CONTAINS OF PROPRIETARY TECHNICAL INFORMATION THAT IS THE PROPERTY OF THIS COMPANY.
ChipSiP CWFC10x Serial Contents CHAPTER 1 INTRODUCTION.........................................5 1.1 INTRODUCTION ..............................................................5 1.2 HARDWARE FEATURES ..................................................6 1.3 SOFTWARE FEATURES ....................................................7 1.4 PACKAGE CONTENTS ......................................................8 CHAPTER 2 HARDWARE INSTALLATION ..................9 2.1 HOW TO INSTALL THE ROUTER .......................
ChipSiP CWFC10x Serial 5.7 VLAN SETTINGS .........................................................53 CHAPTER 6 ROUTING SETUP ......................................55 6.1 QOS.............................................................................55 6.2 ROUTING .....................................................................57 CHAPTER 8 SYSTEM MAINTENANCES.....................59 8.1 STATUS ........................................................................59 8.2 STATISTICS ...................
ChipSiP CWFC10x Serial Chapter 1 Introduction 1.1 Introduction Thank you for purchasing CWFC103 Mobile Multi-purpose Wireless device. CWFC103 is a portable wireless AP/Router with up to 300Mbps transmission rate. It supports five working modes: wireless AP (access point), Client+AP, WDS+AP, WISP Router and Wireless Router. The default mode is wireless Router. Wireless mode can be easily switched by sliding the side switch. There are 3 modes: Router, AP, and Client mode.
ChipSiP CWFC10x Serial 1.2 Hardware Features Standard Wireless LAN Antenna Interface Frequency Range Number of Selectable Channels Data Rate Coverage Area Transmit Power Receiver Sensitivity LED IEEE 802.11b/g/n standards compliant 2T2R Mode External 0dB antenna 2 RJ45 (1LAN, 1WAN) 1 USB Reset/WPS button Slide switch to select Router, AP, or client mode 2.400 ~ 2.4835 GHz (subject to local regulations) 802.11n 20MHz/40MHz 802.11b/g USA, Canada (FCC); 11 channels (2.412GHz ~2.
ChipSiP CWFC10x Serial 1.
ChipSiP CWFC10x Serial 1.
ChipSiP CWFC10x Serial Chapter 2 Hardware Installation 2.1 How to Install the Router After you unpack the box, please make sure all the components are completed. Follow the below setup to setup the CWFC103: 1. Connect the Ethernet cable to the CWFC103 WAN port 2. Connect the other end of the Ethernet cable to the device (for example ADSL) 3. Connect the miniUSB power cord to the CWFC103 miniUSB power 4.
ChipSiP CWFC10x Serial 2.2 LED Indicator and Port Description LED indicators description on front panel: (From R to L) 1. PWR:Indicates CWFC103 is power on. 2. WPS: Flashing indicates CWFC103 is negotiating with the client in WPS mode. 3. WL: Indicates the WIRELESS LAN is connected. 4. WAN: Indicates an Ethernet cable is connected into WAN port. 5. LAN: Indicate an Ethernet cable is connected into the LAN port. 2.
ChipSiP CWFC10x Serial Chapter 3 Wireless Setup This chapter is to describe how to configure CWFC103 to setup different modes: Gateway, AP/Bridge and Wireless ISP mode. Operation Mode: Gateway: In this mode, the device is supposed to connect to internet via ADSL/Cable modem. The NAT is enabled and PCs in LAN ports share the same IP to ISP through WAN port. The connection type can be setup in WAN page by using PPPoE, DHCP client, PPTP client, L2TP client or static IP.
ChipSiP Channel Security CWFC10x Serial Smart select Off 3.2 Configure CWFC103 1. Connect the Ethernet cable to the CWFC103 LAN port and your notebook/computer. 2. Power up to CWFC103. 3. Open Internet Explorer from your notebook/computer 4. Enter: http://10.10.1.1 5. Enter the Username and Password. If this is the first time use, than enter “admin” and “admin” on both username and password. 6. The following screen will show up and follow the instruction 3.2.
ChipSiP CWFC10x Serial Disable Wireless LAN Interface: Default is uncheck (Enable). Check to Disable the Wireless function. Mode: Default Gateway. There are 3 modes: Gateway, AP, Client mode. Network Type: Default is Infrastructure. There are 2 types: Infrastructure and AD HOC. Infrastructure is the standard wifi mode.
ChipSiP CWFC10x Serial Peer connection. SSID: Service Set Identifier is an unique name of the CWFC103 in the wireless network. Wireless client to connect to the wireless network using SSID. Channel Width: Default is 20/40MHz. The channel bandwidth is to improve the wireless performance. 40MHz can be selected for 11b/g and 11n client. 20/40Mhz is recommended for 11n network to improve the throughput. Channel Number: Default is Auto. The effective channel from 1 to 13/Auto of the wireless network. 3.
ChipSiP CWFC10x Serial Fragment Threshold: Default is 2346. The fragmentation threshold defines the maximum transmission packet size in bytes. The packet will be fragmented if the arrival is bigger than the threshold setting. RTS Threshold: Default is 2347. RTS stands for “Request to Send”. This parameter controls what size data packet the frequency protocol issues RTS packet. Beacon Interval: Default is 100. Set the beacon interval of wireless radio.
ChipSiP CWFC10x Serial IAPP: Default is Enabled Protection: Default is Disable Aggregation: Default is Enabled Short GI: Default is Enabled WLAN Partition: Default is Disabled STBC: Default is Disabled 20/40MHz Coexist: Default is Disabled RF Output Power: Default is 100% 3.3 Security Setting This page shows setting up the security of the CWFC103. Turning on the CWFC103 security will prevent any unauthorized access to the wireless network.
ChipSiP CWFC10x Serial 3.3.1 WEP (Wireless Equivalent Privacy) Encryption: WEP. WEP is a basic encryption method using a series of digital either 64 or 128 bits keys. By using the same key on each of the wireless network devices, unauthorized clients can be prevented to access the network. Authentication: Default Auto Key Length: Default 64-bit. User can select either 64/128 bit Key Format: Default is ASCII.
ChipSiP CWFC10x Serial 3.3.2 WPA-PSK Encryption: WPA (WiFi Protected Access) is security protocol for wireless networks that builds on the basic foundations of WEP. It designed to improved the security of WEP. Authentication Mode: Default is Personal. Options: Enterprise (RADIUS) require a Radius server to run this option. WPA Cipher Suite: Default AES. Pre-Shared Key Format: Passphrase Pre-Shared Key: Enter user preferable sentence from 8-63 ASCII characters.
ChipSiP CWFC10x Serial 3.3.3 WPA+802.1X Encryption: WPA (WiFi Protected Access) is security protocol for wireless networks that builds on the basic foundations of WEP. designed to improved the security of WEP. Authentication Mode: Enterprise (RADIUS) require a Radius server to run this option. RADIUS Servers IP Address: Require RADIUS Static IP Address RADIUS Server Port: RADIUS Server Port number. RADIUS Server Password: RADIUS Server Password.
ChipSiP CWFC10x Serial 3.3.4 WPA2-PSK Encryption: WPA2 (WiFi Protected Access) is security protocol for wireless networks that builds on the basic foundations of WEP. It designed to improved the security of WEP. WPA2 is an enhanced version for WPA for stronger encryption. Authentication Mode: Default is Personal. Options: Enterprise (RADIUS) require a Radius server to run this option. WPA Cipher Suite: Default AES.
ChipSiP CWFC10x Serial 3.3.5 WPA2+802.1x Encryption: WPA2 (WiFi Protected Access) is security protocol for wireless networks that builds on the basic foundations of WEP. It designed to improved the security of WEP. WPA2 is an enhanced version for WPA for stronger encryption. Authentication Mode: Enterprise (RADIUS) require a Radius server to run this option. RADIUS Servers IP Address: Require RADIUS Static IP Address RADIUS Server Port: RADIUS Server Port number.
ChipSiP 3.3.6 WPA-Mixed-PSK 3.3.7 WPA-Mixed+802.
ChipSiP CWFC10x Serial 3.3 Access Control This page shows setting up CWFC103 access control using MAC address. There are 2 options: Allowed Listed and Deny Listed. Allowed Listed is any MAC addresses in the list will be able to connect to the CWFC103 and access the internet. Deny Listed is any MAC addresses in the list will not be able to connect to the CWFC103 nor access the internet. Either Allowed Listed or Deny Listed can be used.
ChipSiP CWFC10x Serial 3.4 WDS Settings WDS, Wireless Distribution System, uses wireless media to communicate with other APs, like the Ethernet does. To do this, CWFC103 must be set to the same channel and set MAC address of others Pas which you want to communicate with in the table and enable the WDS. Enable WDS: Default is unchecked, Disable. If Enable WDS, than the communicated wireless device MAC address must be enter.
ChipSiP CWFC10x Serial 3.5 Site Survey This page provides a tool to scan any accessible wireless network. If there is an Access Point or IBSS , than you can connect manually using CWFC103 as a client mode.
ChipSiP CWFC10x Serial 3.6 WPS This page to show setup the WPS (WiFi Protected Setup) mode. This feature will allow a client with WPS feature on automatically synchronize with CWFC103 setting and connect to the CWFC103. A Self-PIN is required or press the button on the back CWFC103 panel. Disable WPS: Default is uncheck. Enable WPS function Client PIN Number: Must be entered a PIN. A wireless client must enter the same PIN in order to to synchronous with CWFC103. 3.
ChipSiP CWFC10x Serial DO NOT FORGET TO CONFIGURE SYSTEM TIME BEFORE ENABLE THIS FEATURE. Enable Wireless Schedule: Default is Disable.
ChipSiP CWFC10x Serial Chapter 4 TCP/IP Settings This Chapter is to present how to configure the LAN and Wireless TCP/IP setup. 4.1 LAN Interface The section is to show how to configure the parameters for local area network connected to the LAN port of the CWFC103. You can configure the IP addresses, subnet mask, DHCP,…etc.
ChipSiP CWFC10x Serial IP Address: Default is 10.10.1.1. It can be changed to any preferable IP address Subnet Mask: Default is 255.255.255.0. This field is related to the IP address Default Gateway: Default is 0.0.0.0. If there is no input in this field, than it will use the default IP address for the default gateway address DHCP: Default is Server. If select DHCP is server, than it will generate the IP address within the DHCP Client Range for the clients DHCP Client Range: Default is 10.10.1.
ChipSiP CWFC10x Serial value of the WAN access type. 4.2.1 Static IP WAN Access Type: Select Static IP as WAN access type.
ChipSiP CWFC10x Serial interface. There are IP address, subnet mask and default gateway settings need to be done. IP Address: If you select the Static IP support on WAN interface, fill in the IP address for it. Subnet Mask: If you select the Static IP support on WAN interface, fill in the subnet mask for it. Default Gateway: If you select the Static IP support on WAN interface, fill in the default gateway for WAN interface out going data packets. MTU Size Fill in the mtu size of MTU Size.
ChipSiP CWFC10x Serial Enable PPTP pass through on VPN connection: Click the checkbox to enable PPTP packet pass through Enable L2TP pass through on VPN connection: Click the checkbox to enable L2TP packet pass through Apply Changes: Click the Apply Changes button to complete the new configuration setting. Reset: Click the Reset button to abort change and recover the previous configuration setting.
ChipSiP CWFC10x Serial 4.2.2 DHCP DHCP Client: Click to select DHCP support on WAN interface for IP address assigned automatically from a DHCP server. Host Name: Fill in the host name of Host Name. The default value is empty MTU Size Fill in the mtu size of MTU Size.
ChipSiP CWFC10x Serial DNS address automatically. Set DNS Manually: Click to select getting DNS address for Static IP support. DNS 1: Fill in the IP address of Domain Name Server 1. DNS 2: Fill in the IP address of Domain Name Server 2. DNS 3: Fill in the IP address of Domain Name Server 3. Clone MAC Address: Fill in the MAC address that is the MAC address to be cloned. Enable uPNP: Click the checkbox to enable uPNP function. Enable IGMP Proxy: Click the checkbox to enable IGMP Proxy.
ChipSiP CWFC10x Serial 4.2.3 PPPoE PPPoE: Click to select PPPoE support on WAN interface. There are user name, password, connection type and idle time settings need to be done.
ChipSiP CWFC10x Serial interface, fill in the user name and password to login the PPPoE server. Password: If you select the PPPoE support on WAN interface, fill in the user name and password to login the PPPoE server. Service Name: Fill in the service name of Service Name. The default value is empty. Connection Type: Select the connection type from pull-down menu. There are Continuous, Connect on Demand and Manual three types to select.
ChipSiP CWFC10x Serial IGMP Proxy. Enable Ping Access on WAN: Click the checkbox to enable WAN ICMP response. Enable Web Server Access on WAN: Click the checkbox to enable web configuration from WAN side.
ChipSiP 4.2.
ChipSiP CWFC10x Serial PPTP: PPTP Allow user to make a tunnel with remote site directly to secure the data transmission among the connection. User can use embedded PPTP client supported by this router to make a VPN connection. Enable Dynamic Mode: Click to select PPTP Dynamic support on WAN interface for IP address assigned automatically from a PPTP server. IP Address: If you select the PPTP support on WAN interface, fill in the IP address for it.
ChipSiP CWFC10x Serial 2. DNS 3: Fill in the IP address of Domain Name Server 3. Clone MAC Address: Fill in the MAC address that is the MAC address to be cloned. Enable uPNP: Click the checkbox to enable uPNP function. Enable IGMP Proxy: Click the checkbox to enable IGMP Proxy. Enable Ping Access on WAN: Click the checkbox to enable WAN ICMP response. Enable Web Server Access on WAN: Click the checkbox to enable web configuration from WAN side.
ChipSiP CWFC10x Serial L2TP: L2TP Allow user to make a tunnel with remote site directly to secure the data transmission among the connection. User can use embedded L2TP client supported by this router to make a VPN connection.
ChipSiP CWFC10x Serial IP Address: If you select the L2TP support on WAN interface, fill in the IP address for it. Subnet Mask: If you select the L2TP support on WAN interface, fill in the subnet mask for it. Gateway: If you select the Static L2TP support on WAN interface, fill in the gateway for WAN interface out going data packets. Server IP Address: Enter the IP address of the L2TP Server.
ChipSiP CWFC10x Serial Enable Ping Access on WAN: Click the checkbox to enable WAN ICMP response. Enable Web Server Access on WAN: Click the checkbox to enable web configuration from WAN side.
ChipSiP CWFC10x Serial Chapter 5 Firewall This Chapter is guided you how to setup the Firewall for CWFC103 to secure and prevent unauthorized access of your local network. 5.1. Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the CWFC103. Use such filters can be helpful in securing or restricting your local network. Enable Port Filtering: Default is uncheck, Disable.
ChipSiP CWFC10x Serial local network on certain ports, fill in the range of start-port and end-port, and the protocol, also put your comments on it. Protocol: The Protocol can be TCP, UDP or Both. Comments: Comments let you know about whys to restrict data from the ports. Apply Changes: Click the Apply Changes button to register the client to new configuration setting. Reset: Click the Reset button to abort change and recover the previous configuration setting.
ChipSiP CWFC10x Serial Enable IP Filtering: Default is uncheck, Disable. If the option is enabled, than the IP Entries in the table will be restricted to access the network. Local IP Address: To restrict data transmission from the local network on certain IP addresses, fill in the IP address, and the protocol, also put your comments on it. Protocol: The Protocol can be TCP, UDP or Both.
ChipSiP CWFC10x Serial 5.3 MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the CWFC103. Use such filters can be helpful in securing or restricting your local network. Enable MAC Filtering: Default is uncheck, Disable. If the option is enabled, than the MAC Entries in the table will be restricted to access the network.
ChipSiP CWFC10x Serial Apply Changes: Click the Apply Changes button to register the client to new configuration setting. Reset: Click the Reset button to abort change and recover the previous configuration setting. Delete Selected: Click to delete the selected clients that will be access right removed from CWFC103. Delete All: Click to delete all the registered clients from the access allowed list. Reset: Click the Reset button to abort change and recover the previous configuration setting. 5.
ChipSiP CWFC10x Serial Enable Port Forwarding: Default is Unchecked, Disable. If enable, IP Address: Enter the IP address of the PC where the applications are being set. Protocol: Select the protocol (TCP/UDP/Both) for the application Port Range: Enter the start and end port number which ranges of the external port used to set the server or internet application. Apply Changes: Click the Apply Changes button to register the client to new configuration setting.
ChipSiP CWFC10x Serial Reset: Click the Reset button to abort change and recover the previous configuration setting. 5.5 URL Filtering URL filter is used to deny LAN users from accessing the internet. Block those URLs which contain keywords listed below. Enable URL Filtering: Default is uncheck, Disable. If the option is enabled, than the URL Entries in the table will be restricted to access the network. URL Address: Add one URL address.
ChipSiP CWFC10x Serial that will be access right removed from CWFC103. Delete All: Click to delete all the registered clients from the access allowed list. Reset: Click the Reset button to abort change and recover the previous configuration setting. 5.6 DMZ DMZ, Demilitarized Zone, is used to provide Internet services without sacrificing unauthorized access to its local private network.
ChipSiP CWFC10x Serial Apply Changes: Click the Apply Changes button to register the client to new configuration setting. Reset: Click the Reset button to abort change and recover the previous configuration setting. Delete Selected: Click to delete the selected clients that will be access right removed from CWFC103. Delete All: Click to delete all the registered clients from the access allowed list. Reset: Click the Reset button to abort change and recover the previous configuration setting.
ChipSiP CWFC10x Serial Enable VLAN: Default is unchecked, Disable. Apply Changes: Click the Apply Changes button to register the client to new configuration setting. Reset: Click the Reset button to abort change and recover the previous configuration setting. Delete Selected: Click to delete the selected clients that will be access right removed from CWFC103. Delete All: Click to delete all the registered clients from the access allowed list.
ChipSiP CWFC10x Serial Chapter 6 Routing Setup This chapter is to guide how to setup the best path for the data frame. 6.1 QoS QoS, Quality of Service, is the ability to provide different priority to different applications: multimedia, VoIP services, online games or IP-TV, users, or data flows, or to guarantee a certain level of performance to a data flow.
ChipSiP CWFC10x Serial Enable QoS: Default is Unchecked, Disable. If select enable, than continue with the following Select Automatic Uplink Speed or Manual Uplink Speed (Kbps). The speed must be entered if Manual Uplink Speed is selected.
ChipSiP CWFC10x Serial Downlink Speed (Kbps). The speed must be entered if Manual Uplink Speed is selected. Address Type: Default is IP.
ChipSiP CWFC10x Serial Enable Dynamic Route: Default is Unchecked, Disabled. If enable dynamic route, than CWFC103 will select the best routing route. Apply Changes: Click on after option is selected Enable Static Route: Default is Unchecked, Disable. If a static route is known, than a static route can be selected.
ChipSiP CWFC10x Serial Chapter 8 System Maintenances This chapter is to show how to maintenance CWFC103. 8.1 Status This page shows the status and basic settings of the CWFC103.
ChipSiP CWFC10x Serial 8.2 Statistics This page shows the packet counters for transmission and reception on the wireless and Ethernet networks.
ChipSiP CWFC10x Serial 8.3 DDNS DDNS, Dynamic DNS, is a service that provides a valid, unchanging, internet domain name (an URL) to go with that related IP address. It assign a fixed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server.
ChipSiP CWFC10x Serial Enable DDNS: Default is Unchecked, Disable. Service Provider: Select from the drop-down menu. Domain Name: It is an optional User Name/Email: Enter user registration name Password/Key: Enter user registration password 8.4 Time Zone Setting The system time can be synchronized with a public time server over the Internet.
ChipSiP CWFC10x Serial Copy Computer Time: Get the time and date from the connected system Enable NTP client update: Default is unchecked, Disable. If enable, than CWFC103 will synchronize the time from the Internet time server. Automatically Adjust Daylight Saving: Default is unchecked, Disable. 8.5 DoS A DoS (Denial Of Service) attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service.
ChipSiP CWFC10x Serial Enable DoS Prevention: Default is UnChecked, Disable 8.
ChipSiP CWFC10x Serial show system log. Enable Log: Default is Unchecked, Disable. Select the options to show on the log. 8.6 Upgrade Firmware The feature allows CWFC103 firmware to be upgraded to a new version. NOTE: DON’T TURN OFF THE POWER DURING THE UPLOAD FIRMWARE. FAILURE TO DO WILL DAMAGE THE CWFC103.
ChipSiP CWFC10x Serial It shows the current Firmware version. Select the firmware file from the local system and select Upload. NOTE: DON’T TURN OFF THE POWER DURING THE UPLOAD FIRMWARE. FAILURE TO DO WILL DAMAGE THE CWFC103. After it successful load the new firmware, select Reset to reset the device to activate the new firmware 8.7 Save/Reload Settings This feature allows the current settings to be saved to a file and/or reload the settings from the file.
ChipSiP CWFC10x Serial Save Settings to File: Save the current setting to a file. Load Settings from file: Load the settings filefrom the local computer/notebook. Select Upload to apply the new setting from the file. Reset Settings to Default: Reset to the setting to original manufacturing setting. 8.8 Password This feature allows user to change or set a new password of the account to access CWFC103. Empty user name and password will disable the protection.
ChipSiP CWFC10x Serial FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ChipSiP CWFC10x Serial FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
