V13.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .............................................................................................................................................................I EuP-Standby and Off Mode Power Consumption Statement: ..................................................................... II FCC Statement ............................................................................................................................................IV FCC RF Radiation Exposure Statement: .......
Preface System Map: LCD Panel Open - Model A Design I .................................................................................1-7 System Map: LCD Panel Open - Model A Design II ................................................................................1-8 System Map: LCD Panel Open - Model A Design III ...............................................................................1-9 System Map: LCD Panel Open - Model B ..........................................................................
Preface Features & Components Overview ....................................................................................................................................................2-1 Hard Disk Drive .........................................................................................................................................2-2 Optical (CD/DVD) Device ........................................................................................................................2-3 Loading Discs .
Preface Shut down ..................................................................................................................................................3-7 Configuring the Power Buttons .................................................................................................................3-8 Resuming Operation ..................................................................................................................................3-9 Power Conservation Modes ...................
Preface Video (VGA) .............................................................................................................................................4-6 LAN ...........................................................................................................................................................4-6 CardReader ................................................................................................................................................4-6 TouchPad ................
Preface Upgrading The Computer Overview ....................................................................................................................................................6-1 When Not to Upgrade ................................................................................................................................6-2 Removing the Battery ................................................................................................................................
Preface 3G Module ...............................................................................................................................................7-24 Wireless Manager ....................................................................................................................................7-28 Wireless Manager Installation .................................................................................................................7-28 Wireless Manager Application ...............
Preface Trusted Platform Module .........................................................................................................................7-64 Enabling & Activating TPM ....................................................................................................................7-65 Trusted Platform Module (TPM) Driver Installation ..............................................................................7-67 Initializing TPM .........................................................
Preface AMD Video Driver Controls Video Driver Installation ..........................................................................................................................C-1 Video (VGA) ............................................................................................................................................C-1 AMD Vision Engine Control Center ........................................................................................................
Preface Keyboard & Pointing Device ....................................................................................................................D-3 Communication .........................................................................................................................................D-3 Power Management ..................................................................................................................................D-4 Power .............................................
Preface Keyboard Shortcuts ................................................................................................................................ E-14 Function/Hot Key Indicators & Control Center ..................................................................................... E-15 Video Features ........................................................................................................................................ E-16 To Configure Displays from Devices (Charms Bar): .........
Preface Charms Bar ............................................................................................................................................. E-38 3G Module (Windows 8) ........................................................................................................................ E-42 3G Configuration in Windows 8 ............................................................................................................. E-43 Charms Bar ..........................................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • • • • Appendix B Appendix C Appendix D Appendix E A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 7 (with Service Pack 1 installed) and Windows 8 operating systems are supported. The majority of this menu covers information covers information related to the Windows 7 operating system, however for specific information on the Windows 8 operating system see Appendix E.
1 Quick Start Guide Model Differences This notebook series includes two different models that vary slightly in design style, color and general appearance (all models have distinct design styles some of which are pictured on the following pages). Not all the model variants, colors, configurations, buttons etc. are pictured in the manual.
Quick Start Guide System Map: LCD Panel Open - Model A Design I 1 Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
1 Quick Start Guide Figure 1 - 3 LCD Panel Open Model A Design II 1. 2. 3. 4. 5. 6. 7. System Map: LCD Panel Open - Model A Design II 1 Wireless Device Operation Aboard Aircraft Built-in PC Camera (Optional) LCD Power Button LED Status Indicators Keyboard Built-In Microphone Touchpad & Buttons The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide System Map: LCD Panel Open - Model A Design III 1 Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
1 Quick Start Guide Figure 1 - 5 LCD Panel Open Model B 1. 2. 3. 4. 5. 6. 7. 8. Built-in PC Camera (Optional) PC Camera LED LCD Power Button LED Status Indicators Keyboard Built-In Microphone Touchpad & Buttons System Map: LCD Panel Open - Model B 1 2 Wireless Device Operation Aboard Aircraft 3 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide LCD Panel Open - Model C 1 2 Wireless Device Operation Aboard Aircraft 3 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
1 Quick Start Guide LED Indicators Icon The LED indicators on the computer display helpful information about the current status of the computer. Icon Color Description Orange DC Power is Plugged In Green The Computer is On Blinking Green The Computer is in Sleep Mode Blinking Orange The PC Camera is In Use (for 14.0” / 35.
Quick Start Guide Hot Key Buttons - Model A Design I Only These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the Silent Mode on/off with one quick button press. Hot Key Function 3 2 1 1 Toggle *Silent Mode (for power saving) 2 Activate the Default Internet Program 3 Activate the Default E-Mail Browser (Note that in Windows 7 without Outlook/Outlook Express installed this button has no function.
1 Quick Start Guide Hot Key Buttons - Model A Design III Only These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the WLAN module on/off with one quick button press. Hot Key Function 3 2 1 1 Toggle WLAN Module On/Off 2 Activate the Default Internet Program 3 Activate the Default E-Mail Browser (Note that in Windows 7 without Outlook/Outlook Express installed this button has no function.
Quick Start Guide Keyboard - Model A Designs I & II The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly. See Table 1 - 6, on page 1 18 for function key details and Appendix E for Windows 8 keyboard information.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work. NumLk & ScrLk Keyboard - Model A Design III The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly.
Quick Start Guide Keyboard - Models B & C The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly. See Table 1 - 6, on page 1 18 for function key details and Appendix E for Windows 8 keyboard information. Function Keys NumLk & ScrLk Keys Play/Pause Key 3G Module Power Toggle Key Numerical Keypad Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard.
1 Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed.
Quick Start Guide Control Center Press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn modules on/off (see Appendix B for full details).
1 Quick Start Guide Figure 1 - 11 Front & Rear Views 1. 2. 3. System Map: Front & Rear Views Model A LED Power Indicators (see Table 1 - 2, on page 1 - 12) Battery Security Lock Slot 1 Model B 1 Model C 1 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 11 for full instructions.
Quick Start Guide System Map: Left Views Figure 1 - 12 Left Views Model A 1 5 4 3 2 1. 2. 5 7 6 3. 4. 5. 6. Model B 2 1 5 4 3 5 6 7 7. Model C 1 2 4 3 5 6 5 DC-In Jack External Monitor Port RJ-45 LAN Jack HDMI-Out Port USB 3.
1 Quick Start Guide Figure 1 - 13 Right Views 1. 2. 3. 4. 5. Microphone-In Jack Headphone-Out Jack USB 2.
Quick Start Guide Disk Eject Warning Changing DVD Regional Codes Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
1 Quick Start Guide Figure 1 - 14 Bottom View Model A 1. 2. 3. 4. 5. System Map: Bottom View - Model A 1 Battery Component Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover 3G USIM Card Cover (Optional) 3 2 3 3 4 5 CPU The CPU is not a user serviceable part. Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Quick Start Guide System Map: Bottom View - Model B Figure 1 - 15 Bottom View Model B 1 1. 2. 3 3 3. 2 4. 5. 3 6. 5 4 3 Battery Component Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover 3G USIM Card Cover (Optional) Speakers CPU 6 6 The CPU is not a user serviceable part. Overheating Bottom Covers To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
1 Quick Start Guide Figure 1 - 16 Bottom View Model C 1. 2. 3. 4. 5. Bottom View - Model C 1 Battery Component Bay Cover Fan Intake/Vent Hard Disk Bay Cover Speakers 3 3 3 2 4 3 3 CPU The CPU is not a user serviceable part. 5 5 Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use. Battery Information Always completely discharge, then fully charge, a new battery before using it.
Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 are accessed from the Start menu (see Appendix E for information on the Windows 8 OS). When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties to customize the appearance of the Start menu.
1 Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 7. For more detailed video information see “AMD Video Driver Controls” on page C - 1. To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. 4. 5. 6. Click Start and click Control Panel. Click Display (icon) - In the Appearances and Personalization category. Click Adjust Screen Resolution/Adjust resolution.
Quick Start Guide To access the AMD Vision Engine Control Center (See Appendix C for detailed information): 1. 2. 3. Right-click the desktop and select AMD VISION Engine Control Center 3 . OR 4 in the Windows taskbar notification area (or right-click the icon and select AMD Double-click the icon VISION Engine Control Center). OR Click Advanced settings 2 (Figure 1 - 18) in the Screen Resolution control panel, click the AMD VISION Engine Control Center 5 tab and then click the control center button 6 .
1 Quick Start Guide 4. 5. Click the Preferences button and select either Advanced View or Standard View. The menu headings allow you to select which items you wish to change.
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 26 or see Appendix E for information on the Windows 8 OS) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
1 Quick Start Guide 1 - 32
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • Hard Disk Drive Optical (CD/DVD) Device Multi-In-1 Card Reader Touchpad and Buttons/Mouse Audio Features For information on the Windows 8 operating system see Appendix E.
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page D - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 15).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes: 1. 2. 3. 4. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times.
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Multi-In-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components Touchpad and Buttons/Mouse The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse. Once you have installed the Touchpad driver (see “TouchPad” on page 4 - 6) you can configure the functions by double-clicking the Touchpad driver icon in the notification area.
Features & Components 2 Show Video You can get a clearer view of the gestures involved by clicking the Show Video option for each gesture item. Select the gesture (Pinch Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Settings left tree menu and click the Show Video button to see the demonstration video.
Features & Components Smart Sense The Smart Sense feature helps prevent operating the Touchpad by accident, by recognizing when your palm is resting on it or brushing its surface while you are typing. You can adjust the sensitivity of Smart Sense by moving the slider towards Max (to help remove undesired pointer movement or clicks) or Off (if it misses intended motions or taps).
Features & Components 2 Figure 2 - 8 Scrolling Gesture Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the Touchpad surface and slide both fingers in the direction required (in a straight continuous motion). Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions.
Features & Components Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the Touchpad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Features & Components 2 Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Deck control panel . The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Features & Components Expert Mode will allow you to access more advanced configuration menus for Speaker, Microphone and Stereo Mix. Syncing Left & Right Volume Balance If you wish to adjust the left and right channel volume levels separately, you will need to adjust this from the VIA HD Audio Deck in Expert Mode. Note that to adjust the Left & Right volume balance independently click the Sync Left and Right Volume icon (it should be faded) and adjust the slider as required.
Features & Components 2 2 - 14
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Silent Mode (Model A Design I Only) Use the key (for Model A computers only) or Control Center button to toggle Silent Mode to reduce fan noise and save power consumption. Note this may reduce computer performance. The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States 3 You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Power Conservation Modes The Energy Star setting will result in maximum power saving, but with the possible loss of some performance. Power Conservation Modes This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center: 1. 2. 3. Press the Fn + Esc key combination to toggle the Control Center on/off.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 2 on page 3 - 5).
Power Management 3 Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 4. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 15 for instructions on how to do this).
Power Management Proper handling of the Battery Pack 3 Caution • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. 4 1. 2. 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. Click to select the driver you wish to install, (you should note down the drivers as you install them).
Drivers & Utilities Win 7 SP1/Win 8 Driver Page # Win 7 SP1/Win 8 Driver Page # PC Camera Module Video (VGA) Page 4 - 6 (Only 14.0” / 35.
Drivers & Utilities Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. 4 Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 7 for instructions.
Drivers & Utilities User Account Control New Hardware Found If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 4 Video (VGA) 1. Click 1.Install VGA Driver > Yes. 2. Click Next > Install (button). 3. Click the Express (or Custom if you prefer to manually configure the driver installation settings) button and click Next. 4. Click Accept (button) and click Yes. 5. Click Finish > Yes to restart the computer.
Drivers & Utilities Audio 1. Click 6.Install Audio Driver > Yes. 2. Click Next. 3. Click the button to agree to the license agreement and click Next. 4. Click Next > Next > Next. 5. Click Finish to restart the computer. Note that after installing the audio driver the system will not return to the Drivers Installer screen.
Drivers & Utilities 4 Windows Experience Index Optional Drivers After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experience Index (make sure the AC/DC adapter is plugged in): See the pages indicated for the driver installation procedures for any modules included in your purchase option. 1. Click Start, and click Control Panel. 2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index). 3.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . UEFI Boot & POST When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities Setup Menus 5 The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC firmware Revision This item contains information on the BIOS version etc., and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu 5 Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting.
BIOS Utilities SATA Mode Selection 5 If you have installed the Windows operating system with either IDE or AHCI mode enabled, DO NOT disable the set mode (if you wish to disable the set mode you will need to reinstall the Windows OS). Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted.
BIOS Utilities Security Menu Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 10 Security Menu Set User Password (Security Menu) You can set a password for user mode access to the Aptio Setup Utility.
BIOS Utilities Secure Boot (Security Menu) Secure Boot prevents unauthorized operating systems and software from loading during the startup process. Secure Boot is available as a menu option if you have Windows 8 set as your operating system, and have enabled UEFI Boot (see “Boot Menu” on page 5 - 15).
BIOS Utilities TPM Configuration (Security Menu) This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support, and to configure the TPM State. Select TPM Configuration and press Enter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to display the full TPM configuration menu (see “Trusted Platform Module” on page 7 - 96 for details).
BIOS Utilities TPM State (Security Menu > TPM Support Enabled) Select TPM State, press Enter and select Enable to change the TPM state to enabled. You will then need to press F4 to save the changes and restart the computer. Figure 5 - 6 TPM State (Enabled) As the computer restarts press F2 to enter the BIOS again and go to the TPM Configuration menu.
BIOS Utilities Pending TPM operation (Security Menu > TPM Support & TPM State Enabled) Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership). You will then need to press F4 to save the changes and restart the computer.
BIOS Utilities Boot Menu Figure 5 - 8 Boot Menu BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot Option Priorities.
BIOS Utilities Boot Option Priorities (Boot Menu) Press Enter to select the Boot Option # and use the + and - keys to move any device’s boot priority up and down the list (the selected device will be highlighted in white). OS Select (Boot Menu) This item tells allows you to set the operating system you intend to use. This item should be set before you install an operating system. 5 UEFI Boot (Boot Menu > OS Select) Enable/disable UEFI Boot from this menu.
BIOS Utilities Exit Menu Figure 5 - 9 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
BIOS Utilities 5 5 - 18
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord). You must also remove your battery in order to prevent accidentally turning the machine on. Before removing the battery disconnect the AC/DC adapter from the computer.
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Upgrading The Computer Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty. Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place.
Upgrading The Computer Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h) (see “Storage” on page D - 3). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (see “Driver Installation” on page 4 - 2), when setting up a new hard disk. HDD System Warning New HDD’s are blank.
Upgrading The Computer 1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and loosen screws 1 & 2 . Remove the hard disk bay cover 3 .
Upgrading The Computer 4. 5. 6. 7. Grip the tab and slide the hard disk in the direction of arrow 4 . Lift the hard disk out of the bay 5 . Remove the screw(s) 6 - 9 and the adhesive cover 10 . Reverse the process to install a new hard disk drive (do not forget to replace all the screws and covers). 9 8 4 6 10 7 Hard Disk Screws & Cover The hard disks and covers pictured here may appear slightly different from your model design (these designs are subject to change and upgrade without notice).
Upgrading The Computer Upgrading the Optical (CD/DVD) Device The procedure for removing the optical device will depend upon your particular computer model: • See “Removing the Optical Device for Model A Computers” on page 6 - 9. • See “Removing the Optical Device for Model B/C Computers” on page 6 - 11.
Upgrading The Computer Removing the Optical Device for Model A Computers 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the component bay cover and remove screws 1 - 4 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover 6 . 1 2 Fan Cable & Cover Make sure you reconnect the fan cable 5 before screwing down the bay cover.
Upgrading The Computer 5. 6. Remove the screw at point 7 , and use a screwdriver to carefully push out the optical device at point 8 . Reverse the process to install the new device.
Upgrading The Computer Removing the Optical Device for Model B/C Computers 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Remove the hard disk (see page 6 - 5) Remove the screw at point 1 , and use a screwdriver to carefully push out the optical device at point 2 . Reverse the process to install the new device.
Upgrading The Computer Fan Cable & Cover 6 Make sure you reconnect the fan cable 5 before screwing down the bay cover. Note the information on replacing the RAM & CPU bay cover in “Cover Pins” on page 6 - 15. Upgrading the System Memory (RAM) This series of computers has two memory sockets, for 204 pin Small Outline Dual In-line (SO-DIMM) DDRIII (DDR3) type memory modules (see “Memory” on page D - 2 for details of supported module types). 1. 2.
Upgrading The Computer 3. 4. Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover 6 .
Upgrading The Computer 5. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 7 & 8 ) in Figure 6 - 8. Figure 6 - 9 RAM Module Release 7 9 6 8 6. 7. 8. The RAM module will 9 pop-up, and you can remove it. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 9. The module’s pin alignment will allow it to only fit one way.
Upgrading The Computer 11. Replace the bay cover by aligning the cover pins (see sidebar - make sure you reconnect the fan cable before screwing down the bay cover). 12. Restart the computer to allow the BIOS to register the new memory configuration as it starts up. Models B & D Models E & F Model A Model B Cover Pins Note that this computer model has four cover pins. These pins need to be aligned with slots in the case to insure a proper cover fit, before screwing down the bay cover.
Upgrading The Computer 6 6 - 16
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • PC Camera Module • Wireless LAN Module • Bluetooth & Wireless LAN Combo Module • 3G Module For information on the Windows 8 operating system see Appendix E.
Modules & Options Important Notice If your purchase option includes both Wireless LAN and 3G modules, then the appropriate antennas will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate in conjunction with any other antenna or transmitter.
Modules & Options PC Camera Module Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 18) to toggle power to the PC Camera module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Note that only 14.0" / 35.56cm Model A computers require a camera driver for Windows 8. When the 14"/35.
Modules & Options PC Camera Screen Refresh 7 The PC Camera module supports a frame rate of 12 fps. If you find that the screen refresh rate is subject to lag or stuttering, then reduce the window size, or adjust the Output Size and/or Color Space Compression. PC Camera Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install Webcam Driver > Yes. 4.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules & Options Figure 7 - 1 Audio Setup for PC Camera Right-click 7 7 - 6 PC Camera Module
Modules & Options Camera Application The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page 7 - 5) and select Start Capture.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Frequency (Anti Flicker).
Modules & Options Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. 7 Taking Still Pictures The camera application allows you to take still pictures. 1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and select Take Picture. The picture (in JPEG format) will be placed in the Snapshot folder desktop.
Modules & Options Wireless LAN Module If you have included a Wireless LAN (or WLAN & Bluetooth combo) module in your purchase option, make sure that the module is on before installing the driver. See “Wireless LAN Settings (Windows 8)” on page E - 30 for Windows 8 configuration information. Wireless Device Operation Aboard Aircraft Use the Fn + F11 key combination (see “Function/Hot Key Indicators” on page 1 - 18) to toggle power to the Wireless LAN module.
Modules & Options 802.11b/g/n Driver Installation (for WLAN Module Only) See over for information on installing the drivers for the WLAN & Bluetooth combo module. If you see the message “Found New Hardware” click Cancel to close the window. 7 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4. Choose the language you prefer and click Next. 5.
Modules & Options 802.11b/g/n Driver Installation (for Combo Modules) If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer (see sidebar for important information).
Modules & Options Network and Sharing Center You can also use the Network and Sharing Center control panel in Windows (Network and Internet) to connect to any available wireless networks. Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. 1.
Modules & Options 2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Modules & Options Security Enabled Networks 5. 6. Click the notification area icon to see any currently connected networks. To disconnect from the wireless network you can click the notification area wireless icon , click the active connection and then click Disconnect (button). You should try to make sure that any network you are connecting to is a secure network. 7 Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F12 key combination to toggle power to the Bluetooth module, and check the LED indicator to see if the module is powered on or not (see Table 1 - 6, on page 1 - 18/ Table 1 - 3, on page 1 - 12).
Modules & Options Bluetooth (V4.0) & WLAN Combo Driver Installation 1. Before installing the driver make sure the Bluetooth module is powered on (use Fn + F12 key combination), then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. If a Found New Hardware window appears, click Cancel in all windows that appear, and then proceed to install the driver as below. 2. Click Option Drivers (button). 3. Click 3.Install Combo BT Driver > Yes. 4. Click Next. 5.
Modules & Options Standard Bluetooth Configuration in Windows 7 Add a Device Click Start, and click Control Panel and then click Devices and Printers (Hardware and Sound). Click Add a device to search for any available Bluetooth devices. 7 Bluetooth Module & Resuming From Sleep Mode Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation).
Modules & Options To Add a Bluetooth Device 1. 2. Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections. You can choose to have the computer create a pairing code for you, use the device’s existing pairing code or you can pair certain devices without using a code. Figure 7 - 8 3.
Modules & Options 4. Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. Figure 7 - 9 Pairing Codes Pairing Code Example 7 The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing. 5. 6. 7.
Modules & Options To Change Settings for the Bluetooth Device 1. 2. • • Click the notification area icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Change the name of the device (click Bluetooth, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3.
Modules & Options 3G Module Options There are two optional 3.G modules available for this series of computer models. Each module is supplied with the appropriate application software. 7 The module type supplied may depend upon the computer model purchased. Check with your distributor/ supplier for details.
Modules & Options 1. 2. Turn off the computer, and turn it over and remove the battery (see page 6 - 4). Locate the 3G USIM card cover and loosen screw 1 , and then remove the USIM card cover 2 . Figure 7 - 12 USIM Card Cover Removal 1 2 3. 4. 5. Insert the USIM card as you would into your mobile phone. Slide the SIMLOCK towards the hinge in order to release the lock and lift it up. Insert the USIM card as illustrated in (Figure 7 - 13) and close the SIMLOCK.
Modules & Options 6. Figure 7 - 14 SIMLOCK Lock 3G Modules & System Wake Up 7 Note that the 3G modules DO NOT support system wake up on 3G modem activity. 7 - 26 3G Module Lock the SIMLOCK by pushing it in the direction of the arrow in Figure 7 - 14 until it clicks into the lock position.
Modules & Options Before installing the application, make sure that the 3G module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see Table 1 - 4, on page 1 - 12) or Control Center button to toggle power to the 3G module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Note that exiting the application does NOT turn off the 3G module.
Modules & Options Wireless Manager Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + key combination to toggle power to the 3G module, and check the indicator to see if the module is powered on or not (see Table 1 - 6, on page 1 - 18/ Table 1 - 3, on page 1 - 12).
Modules & Options Wireless Manager Application The connection information is stored on the USIM card supplied by the service provider (where this is not the case you may need to create a profile - see “Creating a Profile” on page 7 - 35). 1. 2. 3. 4. Power on the 3G module using the Fn + key combination. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . You may be required to enter you PIN number and click OK.
Modules & Options Wireless Manager Help To get help on Wireless Manager configuration and settings, click the Help icon or press F1. 7 Figure 7 - 16 Wireless Manager (Connected) 7 - 30 3G Module 5. 6. 7. The system will connect to your network. Connected will appear above the timer icon (the timer will indicate your connected time for the current session) . You can then access the internet, download e-mail etc. as per any internet connection.
Modules & Options 8. Click the Wireless Manager notification area icon to view the connection status, or wireless icon to view the Mobile Broadband Connection status. Figure 7 - 17 Notification Area Icons (Connected) 9. 10. 11. 12. 13. The indicator will display the signal strength and radio access technology.
Modules & Options Profiles 1. 2. 3. Figure 7 - 18 Advanced Settings Profiles 7 7 - 32 3G Module Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click the Settings > Advanced. Click the Profiles (tab).
Modules & Options 4. Multiple profiles may be available from the USIM card and the first time the application starts it may require you to select a profile (Set Profile) to use for your connection. Figure 7 - 19 Multiple Profiles Found 7 Automatic Profile Selection If Automatic selection is chosen, then the application will search the operator profile database for a profile that matches the details on your USIM card. If a correct profile is found it will be automatically selected as your profile.
Modules & Options Selecting a Profile 1. 2. 3. Figure 7 - 20 Profile - Manual Selection (Filter) 7 7 - 34 3G Module Click Manual selection (button). Click the Filter to view the drop-down list. Select the Profile you wish to use and click Apply to confirm the selection.
Modules & Options Creating a Profile 1. 2. 3. 4. 5. 6. 7. 8. Click Manual selection (button). Click the New. Enter a name you prefer for the profile. Enter the Access Point Name (APN). Enter the User Name and Password if required (some service providers may not require this information and the fields may then be left blank). If your service provider requires IP address, DNS and Protocols to be entered, click the appropriate tab and enter the supplied information (otherwise leave blank).
Modules & Options Settings The Settings tab allows you at adjust the application features. Click to put a tick in Launch Wireless Manager at Windows startup to launch the application at Windows Startup. Figure 7 - 22 Settings 7 The Advanced settings allows more detailed configuration. To access the Advanced settings: 1. 2. 3. 7 - 36 3G Module Access the Wireless Manager program from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut .
Modules & Options SIM Most USIM cards are protected by a Personal Identity Number (PIN). You may turn on or off the Request PIN at startup (click Apply to save any changes). You can also Change PIN (you will need to enter the new PIN in the two fields provided and click Apply to save any changes). Radio Radio needs to be turned on before you can make any connection (note this is not the same as powering the module off/on using the Fn + key combination), but you may turn it off when required.
Modules & Options Warning 7 Note that some applications automatically transmit data when connected, and you may be charged for the data transfer. Some auto connection/connection settings may lead to expensive roaming charges. Figure 7 - 24 Advanced Settings Networks & Connection 7 - 38 3G Module Networks The mobile network list lists available networks at your location, and allows you to select a network which to connect. You must disconnect before being able to select a network.
Modules & Options Text Messaging Service (SMS) In addition to standard internet services you may also send and receive SMS text messages using the Wireless Manager, if your service supports SMS. SMS Utility 1. 2. 3. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start.
Modules & Options Messages Click the Messages tab to access the tabs displaying text messages. The tabs at the top of the menu display the Inbox, Drafts, Outbox, Sent and Trash menus. Inbox Drafts Outbox Sent Trash 7 Figure 7 - 26 SMS Utility Messages Text messages are automatically saved to your computer and may be sorted in ascending or descending order by name or date.
Modules & Options Sending a Text Message 1. 2. 3. 4. 5. 6. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start. Click the New Message tab. Enter the phone number in the To field (multiple numbers may be entered to select a name from separated by a semicolon (;), or click the phonebook icon the phonebook.
Modules & Options 7. 8. 9. Click Send to send the message or Save to save the message in the Drafts folder. clears both the Message and To fields. Clicking the Clear icon If radio is on then the message will be sent, however if the radio is off the message will be stored in the Outbox. Note that you do not have to connect to the network to Send/Receive SMS messages. Inbox Any received text messages will be displayed in the Inbox.
Modules & Options Messages • Opening a text message: Double-click the message and the message will open in a new window (to close it click the close icon in the top right of the message). Figure 7 - 29 Click to close the message • Previewing a text message: Click the preview icon will open. Click the icon again to close the preview. Close Message and the message preview • Replying to a text message: Double-click the message and click Reply.
Modules & Options Phonebook The Phonebook allows you to view and edit all your frequently used contacts, and is divided into Contacts and Groups . To access the Phonebook: 1. 2. 3. 7 Figure 7 - 30 SMS Utility Phonebook (Contacts) 7 - 44 3G Module Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start. Click the Phonebook tab.
Modules & Options Contacts • New Contact: Click the New contact button to create a contact. Add the name and at least one phone number (Mobile, Work, Home and Other fields are available) for the contact. Click the icon to expand the number details. Select Synchronize with SIM to synchronize the contact information with your USIM card. Click the Save icon to save the information. Import/Export Contacts Import/Export Contacts: Click the Import/ Export buttons to import or export the list of contacts.
Modules & Options Groups You can organize existing contacts into groups from the Groups tab. • New Group: Click the New group button to create a group. Click the icon to expand the group details, and click a check box to add at least one phone number from the contacts for the group. Click the Save icon to save the information.
Modules & Options SMS Settings The SMS Utility Settings tab allows you at adjust the SMS features. Figure 7 - 33 SMS Utility Settings SMS Settings Message Length: You can set the number of blocks that can be sent (up to a length of 10 blocks). The Advanced settings allows more detailed configuration. To access the Advanced settings: 1. 2. 3. 4. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut .
Modules & Options Send Click Delivery Report to automatically request a reply from a recipient. If you click to Send messages in Outbox automatically upon connection then messages written when the radio is off, will then be sent automatically the next time radio is turned on. You can also choose to Include original message in reply. Notification This menu allows you to enable/disable Show animation on new message to get an animated notification of newly received messages.
Modules & Options Number You can choose to Use default service center number or you can uncheck the box and add your number manually if your service provider supplies a different number (click Apply to save the change or Default to return to the default number). Memory Phonebook memory status displays the number of contacts displayed on the USIM card.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + key combination to toggle power to the 3G module, and check the indicator to see if the module is powered on or not (see Table , on page 1 - 12/ Table 1 - 3, on page 1 - 9).
Modules & Options AirCard Watcher Application The connection information is stored on the USIM card supplied by the service provider (where this is not the case you may need to create a profile - see “Profiles” on page 7 - 57). 1. 2. 3. 4. Power on the 3G module using the Fn + key combination. Access the AirCard Watcher application from the Start menu (Start > All . Programs > Sierra Wireless > AirCard Watcher) or the desktop shortcut If you need to set up a network operator (see page 7 - 56).
Modules & Options AirCard Watcher Help Topics To get help on AirCard Watcher configuration and settings, click the Menu icon and select Help Topics. 7 Figure 7 - 37 AirCard Watcher (Connected) 7 - 52 3G Module 5. 6. 7. The system will connect to your network. The icon will turn green (and the upload/download speeds will be indicated). You can then access the internet, download e-mail etc. as per any internet connection.
Modules & Options 8. 9. When connected the uplink/downlink speeds will be indicated. to get a visual display of the uplink/ You can also click the Speed Graph icon downlink speeds. 10. While connected you can also click the icon in the notification area of the taskbar to display the Windows 7 Mobile Broadband connection status. Roaming Notification AirCard Watcher will provide notification when you connect to a network other than your service provider.
Modules & Options Online Help Click the Online Help icon to access the Sierra Wireless website for further help if required. 7 Figure 7 - 39 AirCard Watcher Disconnect & Taskbar Menu Disconnect 7 - 54 3G Module 11. To disconnect from the service provider, click the Disconnect button (note that if you click the close icon at the top right of the screen the application will close however the connection will still be maintained). 12.
Modules & Options Air Card Watcher Menu Right-click the menu button at the top of the AirCard Watcher screen to bring up the menu, and click to select any item required. Airplane Mode Click on the Airplane Mode icon to turn the radio power off (e.g. if you are aboard an aircraft). You can turn the radio on again by clicking the Turn Radio On button.
Modules & Options Network Operator If the network operator is not listed then choose Generic UTMS. Selecting a Network Operator/Service Provider In most cases all your network operator/service provider details will be stored on your USIM card, and will not need to be edited/modified. If you do need to set up a network operator/service provider follow these instructions. 1. 2. 3. 4. 5.
Modules & Options Profiles A profile contains information used to establish a data connection, and this information is usually stored on the USIM card supplied by your service provider. However you can create, edit or delete profiles if required. Creating a Profile 1. 2. 3. 4. Access the AirCard Watcher application from the Start menu (Start > All Programs > Sierra Wireless > AirCard Watcher) or the desktop shortcut . Make sure you are not connected to a network.
Modules & Options 5. Edit or Delete Profiles Select any existing profiles to edit or delete it, and then click OK to confirm any changes made. 7 You can also change the default profile from the dropdown menu and then click OK to confirm the changes. Figure 7 - 43 Profile - Advanced 7 - 58 3G Module 6. 7. You will need to complete the fields for Profile name, Username, Password and Access Point Name (you will need to get the username and password details from your service provider).
Modules & Options User Options You can configure User Options as follows. 1. 2. 3. Access the AirCard Watcher application from the Start menu (Start > All Programs > Sierra Wireless > AirCard Watcher) or the desktop shortcut . Either click the menu button and select Options, or click the Options button from the main program window.
Modules & Options • General - This item allows you to set options for Startup/Shutdown, Warning Messages, Display and Windows support. • Messaging - Set options here for SMS settings. • Network - Configure the network settings from this menu though your frequency band information is usually stored on the USIM card. • SIM Settings - You can set your SIM Security and PIN # options here. • Sounds - This allows you to set sounds applicable to certain application actions e.g. when a new SMS arrives.
Modules & Options Text Messaging Service (SMS) In addition to standard internet services you may also send and receive SMS text messages using AirCard Watcher, if your service supports SMS. SMS Express 1. 2. Access the AirCard Watcher application from the Start menu (Start > All Programs > Sierra Wireless > AirCard Watcher) or the desktop shortcut . Either click the menu button and select SMS Express, or click the SMS from the main program window.
Modules & Options Sent Messages Sent messages will be automatically saved to the Sent Items folder. Sending a Text Message 1. 2. 3. 4. 5. 6. Access the AirCard Watcher application from the Start menu (Start > All Programs > Sierra Wireless > AirCard Watcher) or the desktop shortcut . Either click the menu button and select SMS Express, or click the SMS from the main program window. Express button Select File > New Message or click the New button in the toolbar.
Modules & Options Inbox Any received text messages will be displayed in the Inbox. The number of total messages and unread messages will be displayed in the inbox folder title. Messages • Opening a text message: Click on any message in the Inbox to read it in the bottom panel of the window. • Replying to a text message: Click on any message in the Inbox and select Actions > Reply or click the Reply button in the toolbar.
Modules & Options Trusted Platform Module The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a system administrator before users can access security features. Individual users can use the TPM as an authentication with the fingerprint reader.
Modules & Options Enabling & Activating TPM 1. 2. 3. 4. 5. 6. Restart the computer. Enter the Aptio Setup Utility pressing F2 during the POST/startup. Use the arrow keys to select the Security menu Select TPM Configuration and press Enter. Select TPM Support and press Enter, select Enable and press Enter. Select TPM State, press Enter and select Enabled to change the TPM state to enabled. You will then need to press F4 to save the changes and restart the computer. 7 Figure 7 - 47 TPM State (Enabled) 7.
Modules & Options 8. Select Pending TPM operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership) and press Enter. You will then need to press F4 to save the changes and restart the computer. 9. You can now install the TPM driver (see “Trusted Platform Module (TPM) Driver Installation” on page 7 - 67) and then initialize the TPM.
Modules & Options Trusted Platform Module (TPM) Driver Installation 1. Make sure you have enabled and activated the TPM in the BIOS before installing the driver (if you do not do see the note below). 2. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 3. Click Option Drivers (button). 4. Click 7.Install TPM Driver > Yes. 5. Click Install > Next. 6. Click the button to accept the license and click Next. 7. Click Next > Next > Install. 8.
Modules & Options Initializing TPM 1. 2. 3. 4. 5. 7 Run the application from the Infineon Security Platform Solution > Manage Security Platform item in the Start > All Programs menu. Click User Settings (tab) and click Yes, or right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble).
Modules & Options 6. 7. Choose the Security Platform Features you want to use by clicking the appropriate tickbox. Enter a Basic User Password (and re-type to confirm it) and click Next. Figure 7 - 50 Settings Help Right-click the icon in the notification area of the taskbar to bring up the menu to select Help or How to use the Security Platform Features. 8. 9. 10. 11. 12. Click Next to confirm the settings. The computer will then initialize the settings. Click Finish.
Modules & Options Menus Note that not all the menus pictured here will be available for access. The menu items that appear will be dependent on your configuration settings etc. (see the Help file for full details). Infineon Security Platform Settings Tool The Infineon Security Platform Settings Tool allows you to manage and check the TPM state, manage your password information, and to backup and restore the TPM data.
Modules & Options User Settings This page allows the settings to be configured for the currently logged in Infineon Security Platform user including the ability to change the password, configure secure e-mail, file and folder encryption and Enhanced Authentication. You can also import or delete certificates protected by the security platform.
Modules & Options Backup Here you can configure backup and restore operations. Backup files contain the computer identification and user identification information which is used to match the machine name and user name with the current machine and user during restoration.
Modules & Options Migration The Migration tab is used to help securely transfer keys and certificates from one platform to another.
Modules & Options Password Reset Use Password Reset to reset basic user passwords when required.
Modules & Options BitLocker BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk and is done via the Microsoft BitLocker Control Panel Applet. Click Configure and select a drive to be encrypted and then follow the Wizard to begin the encryption process.
Modules & Options Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security).
Modules & Options Advanced Configure all the Security Platform owner and policy settings from the Advanced tab. The settings that can be changed are for the local computer only.
Modules & Options 7 7 - 78
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LCD Panel Open - Model C” on page 1 - 11) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 24). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution I am sliding my finger up and down on the right side of the Touchpad to scroll a Window and the Touchpad does not respond. There are different Touchpad versions available on this computer, and this version requires tapping/holding to scroll. Either tap repeatedly, or hold the finger down, at the top or bottom right of the Touchpad (depending on the scrolling direction required) to scroll the window.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/Bluetooth/3G modules cannot be detected. The modules are off. Check the LED indicator and/or function key indicator to see if the WLAN/Bluetooth/3G module is on or off (see “LCD Panel Open Model C” on page 1 - 11). If the LED indicator is off, then press the Fn + F11 (WLAN), Fn + F12 (Bluetooth) or Fn + (3G) key combination(s) in order to enable the modules (see Table 1 - 6, on page 1 - 18). The PC Camera module cannot be detected.
Troubleshooting Problem The Bluetooth module resuming from Sleep. Possible Cause - Solution is off after I cannot obtain high speed Bluetooth data transfer. 8 The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep.
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Windows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver. 1. 2. 3. 4. 5.
Troubleshooting 6. 7. 8. 8 Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... 9. Select Bluetooth Radios from the list.
Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list). 12. Select Windows Mobile-based device support from the Model list. 8 Make sure you select Microsoft Corporation Figure 8 - 4 - Select Device Driver 13.
Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Description Microphone-In Jack Plug an external microphone in to this jack to record on your computer. RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.
Interface (Ports & Jacks) A A - 4
Control Center Appendix B: Control Center Overview The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the slider where applicable. Certain functions will automatically be adjusted when a power mode is selected.
Control Center Power Modes You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect the power status of modules (e.g. WLAN, Bluetooth, 3G or Camera), screen brightness, TouchPad power and Silent Mode. You can click a Control Center icon to set an overall power mode and then click individual icons in the Control Center to power on/off any modules etc. The table overleaf illustrates the basic settings for each power mode.
Control Center Power Saving Flight (Win 7 Only) Entertainment Quiet Performance Power Plan Power Saver Balanced Power Saving Power Saving High Performance Power Conservation Mode Energy Star BIOS Default Energy Star Energy Star Performance Brightness 14 42 100 42 100 WLAN (Win 7 Only) OFF OFF ON ON ON Modes User Defined Icon BIOS Default 3G (Win 7 Only) OFF OFF OFF OFF OFF PC Camera OFF OFF OFF ON ON TouchPad ON ON ON ON ON User Defined Bluetooth (Win 7 O
Control Center Power Status The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight (press any key to turn it on again).
Control Center Sleep Click the Sleep button to bring up the Hibernate or Sleep buttons, and click either button to have the computer enter the appropriate power-saving mode (see “Power-Saving States” on page 3 - 6). Display Switch Click the Display Switch button to access the menu (or use the priate attached display mode (see page C - 15). + P key combination) and select the appro- Time Zone Clicking the Time Zone button will access the Date and Time Windows control panel.
Control Center Silent Mode Click the Silent Mode button toggles silent mode on/off. You can use Silent Mode to reduce power consumption and fan noise. Note that the Silent Mode effected by the Power Mode selected. • Silent Mode is OFF • Silent Mode is On Note Silent Mode may reduce computer performance. Caps Lock/Scroll Lock/ Number Lock Click the button to toggle the appropriate lock mode.
Appendix C: AMD Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 28. For information on the Windows 8 operating system see Appendix E. Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Video (VGA) 1. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 2. Click 1.Install VGA Driver > Yes. 3. Click Next > Install (button). 4.
AMD Vision Engine Control Center Adjust the video settings from the AMD Control Center. Taskbar Icon 1. The Control Center can also be accessed by double-clicking the icon in the taskbar notification area (or by right-clicking the icon and selecting the control center). If you don’t see the icon in the taskbar, click Preferences in the control center, and select Enable System Tray Menu (see over). 2. Right-click the desktop and select AMD Vision Engine Control Center.
AMD Vision Engine Control Center Preferences The Preferences button in the control center menu allows you to configure the control panel settings. You can view the control panel in either Standard View or Advanced View. To display Standard View or Advanced View: 1. 2. Open the control center. Click the Preferences button and select either Advanced View or Standard View. Advanced View Standard View Preferences & Views You can switch between Advanced and Standard views from the Preferences menu.
Standard View The Standard View menus feature a series of menu headings with clickable submenus which allow you to adjust Desktops and Displays, Power, Video, Gaming and Information. Click the Start button to access the top level menu from any submenu heading.
Advanced View The Advanced View menus display all the menu headings as a series of buttons on the left. Click the arrows in any button to display the sub-menus (note all the figures in the remainder of this chapter are in Advanced View). Sub-Menus Click a menu button to expand any sub-menus, and then click the appropriate sub-menu heading to configure the item. Click a menu button to expand the sub-menus.
Help Menus The control center provides additional video configuration controls and tools which allow quick access to features such as display options, 3D Settings, color, power and Information menus etc. Adjust settings from the options in the sub-menus. Press F1 to bring up Help menu. Click the question mark icon in the top right to bring up help on a specific page.
Display Devices & Options Besides the built-in LCD you can also use an external monitor/flat panel display/TV connected to the external monitor port or to the HDMI-Out port (High-Definition Multimedia Interface) as your display device. The table below outlines the display options.
Detect Displays Click Detect Displays (button) to automatically update the attached display information. Configuring an External Display You can use the control center to configure any attached displays. 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Open the control center. Select Desktop Management from the menu on the left (click the arrow to expand the menu) and click Creating and Arranging Desktops.
5. 6. Click the triangle icon (or right-click the display icon) on the attached display icon at the bottom to bring up the options (e.g Duplicate or Extend). Select an option from the menu (click Continue if required), and click Yes to accept the settings. Disable Displays If you want to disable any of the displays, right-click the display icon at the bottom of the screen and click Disable. Figure C - 7 Attached displays will appear here. 7.
Desktop Properties Use Desktop Properites (Desktop Management) to configure the desktop area resolution, color quality, refresh rate and rotation. If the displays are configured in Extend mode then they may be configured independently.
My VGA Displays/My Digital Flat-Panels An additional menu button entitled My VGA Displays/My Digital Flat-Panels will appear (depending on the type of display attached) when an external display is attached. This menu allows you to configure the properties of the external display. After making any adjustments you may need to click the Apply button to confirm the changes.
HDTV Support If your flat panel supports HDTV functions then this can be configured from My Digital Flat-Panels > HDTV Support (Digital Flat-Panel).
Configuring an External Display In Windows 7 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see “Video Features” on page 1 - 28). Click the Detect button. The computer will then detect any attached displays.
5. You can configure the displays from the Multiple Displays menu. Figure C - 12 Screen Resolution Multiple Display Options (Win 7) C • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7. 1. 2. 3. 4. Attach your external display to the external monitor port and turn it on. + P key combination. Press the An on-screen menu will pop up. + P) to select the appropriate configuration from the Use the cursor keys (or menu, and press Enter to confirm the selection.
PowerPlay™ When enabled, PowerPlay™ can be used to automatically set to adjust the graphics processor settings for higher performance or longer battery life when the system is either Plugged In or on Battery.
HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. Configure the audio output as per the instructions below. 1. 2. 3. 4. Connect a device with HDMI support to the HDMI-Out port. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound), and click Playback (tab).
5. 6. Double-click the connected HDMI device (or right-click and select Properties) to adjust the HDMI settings from the control panel tabs. Click OK to close the control panel (see notes overleaf).
HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. • To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual). HDMI Video Configuration 1. 2. 3. 4. Connect an HDMI cable from the HDMI-Out port to your external display.
C C - 20
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications Processor Options Memory Video AMD-E Series (Dual-Core) Accelerated Processing Unit - E2-1800 (1.7GHz) 1MB L2 Cache, 40nm (40 Nanometer), TDP 18W, DDR3 - 1333MHz Dual Channel DDRIII (DDR3) AMD Radeon™ HD 7340 Graphics (Integrated with E2-1800 & E2-2000 APUs) AMD-E Series (Dual-Core) Accelerated Processing Unit - E2-2000 (1.75GHz) 1MB L2 Cache, 40nm (40 Nanometer), TDP 18W, DDR3 - 1333MHz AMD-E Series (Dual-Core) Accelerated Processing Unit - E1-1200 (1.
Specifications Storage Card Reader Keyboard & Pointing Device One Changeable 12.7mm(h) Super Multi Optical Device Drive with SATA Interface (Factory Option) Embedded Multi-In-1 Card Reader - MMC/ RS MMC - SD/ Mini SD / SDHC/ SDXC - MS/ MS Pro/ MS Duo Note: Some of these cards require PC adapters that are usually supplied with the cards.
Specifications For Models A & B Only: UMTS/HSPDA-based 3G Module with Full Size Mini-Card Interface (Factory Option) Quad-band GSM/GPRS (850 MHz, 900 MHz, 1800 MHz, 1900 MHz) MTS WCDMA FDD (2100 MHz) Note that UMTS modes CAN NOT be used in North America Design Feature (Factory Option) 6 Cell Smart LithiumIon Battery Pack, 48.84WH (Factory Option) 6 Cell Smart LithiumIon Battery Pack, 62.
Specifications Dimensions & Weight Model A: 341mm (w) * 238.5mm (d) * 16 - 34mm (h) 2.05 kg (with 48.84WH Battery and ODD) OR 340mm (w) * 238mm (d) * 25.05 - 33.05mm (h) 2.0 kg (with 48.84WH Battery and ODD) OR 341mm (w) * 238.5mm (d) * 16 - 34mm (h) 2.2 kg (with 48.84WH Battery and ODD) OR 340mm (w) * 238mm (d) * 25.05 - 33.05mm (h) 2.15 kg (with 48.84WH Battery and ODD) Model B: 374mm (w) * 250mm (d) * 14.3 - 34.1mm (h) 2.25 kg (with 48.84WH Battery and ODD) OR 374mm (w) * 250mm (d) * 20 - 37.2mm (h) 2.
Specifications D D - 6
Windows 8 Appendix E: Windows 8 Overview This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows 8 OS. You can refer to the main manual for details of drivers required, audio & video information, BIOS, modules etc. However any information specific to Windows 8 will be included in this Appendix, as well as details on how to navigate the Windows 8 Metro User Interface to access the applications, control panels, taskbar etc.
Windows 8 Windows 8 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows 8 are accessed from the Metro user interface’s Start screen and/or Windows Desktop. The Desktop (which runs as an app within the Start screen) can be accessed from the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination).
Windows 8 Apps & Tiles The Windows 8 Start screen will contain a number of Apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary apps. Accessing Pining/Unpinning All Apps You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Metro UI Start screen and you will see the All Apps icon.
Windows 8 Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop. To do so move your mouse to hover over the bottom left corner of the screen and click the pop-up. When you move to the lower left hot corner in the Start screen itself it will take you back to your most recently used app.
Windows 8 When the Desktop app is running you can right-click the lower left hot corner (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, Windows Explorer, Command Prompt, Device Manager and Network Connections etc.
Windows 8 Windows 8 Charms Bar The right side of the screen displays the Windows 8 Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
Windows 8 Charms Bar Items • Search results. • Share : You can search for any file, application, apps and control panel settings with instantaneous : This button is used to share information with people via mail or social networks. • Start : Click to bring up the Start Menu (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen). • Devices : Click this button to change connected peripheral device settings e.g. an external display.
Windows 8 Windows 8 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel is much the same as that in Windows 7, however it can be accessed in a number of ways in Windows 8. • Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left.
Windows 8 • When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu. Figure E - 9 - Settings Charms Bar (Desktop App Only) • Right-click on a blank area of the Metro UI Start screen, click the All Apps icon and click Control Panel.
Windows 8 • Right-click the lower left hot corner to bring up the menu and select Control Panel (see Figure E - 4 on page E - 5). Keyboard Shortcut to Control Panel You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.
Windows 8 Windows 8 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the taskbar. In Windows 8 the taskbar is accessed from the Desktop application. If you are in the Start screen you will need to click the Desktop app to switch to the Desktop. The taskbar is displayed in much the same way as it was in Windows 7, and you can see the notification area of the taskbar in the bottom right of the screen.
Windows 8 LED Indicators Icon The LED indicators on the computer display helpful information about the current status of the computer. Icon Windows 8 Color Description Orange DC Power is Plugged In Green The Computer is On Blinking Green The Computer is in Sleep Mode Blinking Orange The PC Camera is In Use (for 14.0” / 35.
Windows 8 Keyboard - Windows 8 The main difference between the Windows 7 & Windows 8 keyboards is in the function of the Windows Logo Key & Menu/Application Key (in the Start screen), otherwise the keyboard functions are identical (see “Keyboard - Model A Designs I & II” on page 1 - 15/“Keyboard - Model A Design III” on page 1 - 16/“Keyboard Models B & C” on page 1 - 17).
Windows 8 Keyboard Shortcuts The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows 8.
Windows 8 Function/Hot Key Indicators & Control Center The function/hot key indicators and Control Center function in the same manner as outlined for Windows 7 (except for the Mute, Volume and Brightness indicators which use the standard Windows 8 indicators) in “Function/Hot Key Indicators” on page 1 - 18 and “Control Center” on page 1 - 19.
Windows 8 Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 8 in the same manner as Windows 7 running the Desktop app (see “Desktop Application” on page E - 4 and Appendix C). In Windows 8 it is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “Windows 8 Charms Bar” on page E - 6). To Configure Displays from Devices (Charms Bar): 1. 2. 3. 4.
Windows 8 Power Options Power Options can be accessed from the Control Panel in the same manner as Windows 7. The Power Menu item in Settings in the Charms Bar in Windows 8 may be used to Shut down, Restart or send the computer to Sleep. Shut Down, Restart or Sleep 1. 2. 3. Go to the Charms Bar and click Settings. Click Power . Select Sleep, Shut Down or Restart.
Windows 8 Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Windows 8 interfaces/apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Windows 8 Wake On LAN Settings If you require your computer to wake up from network activity in Windows 8 then make sure that the computer is either in Sleep or Hibernate. The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a powersaving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. Wake On LAN Support (Windows 8) Wake-On-LAN is only supported from Sleep or Hibernate states in Windows 8.
Windows 8 Screen Resolution for Metro Style Apps (Windows 8) The minimum resolution in which Metro style apps will run is 1024x768. The minimum resolution required to support all the features of Windows 8 (including multitasking with snap) is 1366x768. Running Metro UI Apps To run Apps in the Metro UI in Windows 8 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements: Screen Resolution Settings 1.
Windows 8 User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run Metro Apps, then that you have to check the status of User Account Control (UAC). Metro Apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below. 1. 2. 3. 4. Open the Control Panel (see “Windows 8 Control Panel” on page E - 8).
Windows 8 Drivers & Utilities Make sure you install all the drivers and uti lites for your system. Follow the instructions in Chapter 4 “Drivers & Utilities” on page 4 - 1/“Modules & Options” on page 7 - 1 for installing all the basic system drivers and module drivers for Windows 7 & 8. However note that the USB 3.0 driver is not required for Windows 8, and that the PC Camera driver is only required for 14.0” / 35.56cm Model A computers.
Windows 8 Driver Installation (Windows 8) 1. 2. 3. Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Driver Installation If you miss the message above you can eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it. Alternatively double-click the disc icon in Computer (use the Windows logo key + E key combination to go to Computer in Windows Explorer). 4.
Windows 8 Win 7 SP1/Win 8 Driver Page # Win 7 SP1/Win 8 Driver Page # Video (VGA) Page 4 - 6 PC Camera Module (see page E - 25) (Only 14.0” / 35.
Windows 8 PC Camera (Windows 8) Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 18) or Control Center button to toggle power to the PC Camera module. A PC Camera driver is only required if you have a Model A computer with a 14"/35.56cm screen (see “PC Camera Driver Installation” on page 7 - 4). Model B computers do not require any driver installation. When the 14"/35.
Windows 8 Metro UI Camera App 1. 2. 3. Make sure the PC Camera is turned on by using the Fn + F10 key combination (or Control Center button). Run the Camera App from the Metro UI by clicking on the Camera App icon . The camera interface is a translucent app bar with three buttons. Figure E - 21 - Camera App Bar • Camera options:.
Windows 8 You can also click on More to adjust Brightness, Contrast and Flicker (if you find that the video screen in the camera program is flickering, you can try to adjust the setting here), Figure E - 23 -More Camera Options • Video Mode: This button toggles between still photo mode (transparent button mode (highlighted white button ).
Windows 8 Taking Pictures/Capturing Video 1. 2. 3. 4. 5. 6. 7. Make sure the PC Camera is turned on by using the Fn + F10 key combination (or Control Center button). Run the Camera App from the Metro UI by clicking on the Camera App icon . Click to select the timer if you require a countdown before capture. Click to select either photo or video modes. Click in the main window to take a picture or start video capture (if video capture begins a timer will appear in the bottom right corner of the screen).
Windows 8 8. 9. A scroll arrow will appear on the left side of the screen after any pictures/videos have been captured. Click the arrows (on either side of the screen) to browse through the captured photos/video, and back to the Camera App. 10. Clicking on a captured photo will bring up an App bar with Crop and Delete buttons. Figure E - 25 - Crop & Delete Buttons (for Still Photos) 11. Use the handles to Crop any captured picture, and click OK to save the changes made. 12.
Windows 8 Wireless LAN Settings (Windows 8) If you have included a Wireless LAN (or WLAN & Bluetooth combo) module in your purchase option, make sure that the WLAN module is on before installing the driver. Use the Fn + F11 key combination (see “Function/Hot Key Indicators” on page 1 - 18) or Control Center button to toggle power to the Wireless LAN module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. See “802.
Windows 8 WLAN Configuration in Windows 8 You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Windows 8 4. 5. 6. 7. 8. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. When you are connected to the network access point it will display the Connected icon . Select any connected network and click Disconnect to disconnect from a connected access point. Windows 8 Figure E - 28 - Networks Connected / Disconnect 9.
Windows 8 11. You need to either use Airplane Mode, or to turn the WLAN module off aboard aircraft. Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module is either OFF or in Airplane Mode (for Windows 8 only) if you are using the computer aboard aircraft.
Windows 8 Desktop Mode 1. 2. 3. 4. 5. 6. 7. Switch to the Windows Desktop (click the App or use the Windows logo key + D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not.
Windows 8 Control Panel If you are in Category View do the following (see over for Icon View): 1. 2. 3. Open the Control Panel (see “Windows 8 Control Panel” on page E - 8). Click the Network and Internet control panel. Click Connect to a network. 4. 5. 6. 7. 8. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next.
Windows 8 If you are in Icon View do the following: Windows 8 1. 2. 3. 4. Open the Control Panel (see “Windows 8 Control Panel” on page E - 8). Click Network and Sharing Center. Click Change Adapter Settings. Double-click Wi-Fi. 5. 6. 7. 8. 9. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not.
Windows 8 Bluetooth Settings (Windows 8) If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed in Chapter 7 (see links below). Use the Fn + F12 key combination or Control Center button to toggle power to the Bluetooth module. Bluetooth Data Transfer Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Windows 8 Bluetooth Configuration in Windows 8 You can configure a Bluetooth connection as below, however make sure the Bluetooth module is turned on (and not in Airplane Mode) before configuration begins. Desktop Mode 1. 2. 3. Switch to the Windows Desktop (click the App or use the Windows logo key + D key combination). Click the notification area of the taskbar and double-click the Bluetooth icon (or click and select Show Bluetooth Devices). The Devices item in PC Settings will appear. OR Charms Bar 1.
Windows 8 4. 5. Click Add a Device. Double-click the device you want to pair with the computer. Figure E - 34 - PC Settings (Devices) - Add A Device 6. On first connection the computer will provide you with a pairing code to be entered onto the device. 7. Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing.
Windows 8 8. You need to either use Airplane Mode, or to turn the Bluetooth module off aboard aircraft. Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module is either OFF or in Airplane Mode (for Windows 8 only) if you are using the computer aboard aircraft.
Windows 8 To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. 4. Switch to the Windows Desktop (click the App or use the Windows logo key + D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a tick inside it.
Windows 8 3G Module (Windows 8) (For Models A & B Only) If you have included an optional UMTS/HSPDA OR UMTS/HSPDA+ based 3G Module (Universal Mobile Telecommunications System or High Speed Packet Access) module (see “Communication” on page D - 3 for specification details) in your purchase option, you do not require a driver/application installation for Windows 8.
Windows 8 3G Configuration in Windows 8 You can configure a 3G connection as below, however make sure the 3G module is turned on by pressing the Fn + key combination (give the module about 10 seconds to power on) or Control Center button (and not in Airplane Mode) before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Windows 8 4. 5. Any 3G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband. Double-click any connection icon under Mobile Broadband (or click and click Connect). Figure E - 39 - Mobile Broadband (Connect) 6. 7. The system will connect to your network. A Connected will appear alongside the 3G connection (click the connection to view the timer which indicates your connected time for the current session).
Windows 8 8. You can then access the internet, download e-mail etc. as per any internet connection. 9. To disconnect you can select the connection and click Disconnect . 10. You need to either use Airplane Mode, or to turn the Mobile Broadband module off aboard aircraft. Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Windows 8 Windows 8 E - 46
