V10.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VIII • Only use a power adapter approved for use with this computer.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface XVI
Preface Contents Notice .................................................................................I FCC Statement ................................................................ III FCC RF Radiation Exposure Statement: ........................ IV Instructions for Care and Operation ............................... VI Power Safety ................................................................ VIII Polymer Battery Precautions .......................................... IX Battery Precautions ........
Preface Parallel Printer .............................................................2-14 Drivers & Utilities Power Management What to Install ................................................................4-1 Module Driver Installation .............................................4-1 Driver Installation ..........................................................4-2 Updating/Reinstalling Individual Drivers ......................4-4 User Account Control ...................................................
Preface Failing the POST ...........................................................5-3 Fatal Errors ....................................................................5-3 Non-Fatal Errors ............................................................5-3 The Setup Utility ............................................................5-4 Entering Setup ...............................................................5-4 Setup Screens .................................................................5-5 Main Menu .
Preface Bluetooth & WLAN Combo Settings ..........................7-29 Bluetooth Networking Setup .......................................7-32 Bluetooth & WLAN Combo Module Configuration ...7-33 Standard Bluetooth Configuration in Windows 7 .......7-36 Troubleshooting Overview ........................................................................8-1 Basic Hints and Tips ......................................................8-2 Backup and General Maintenance .................................8-3 Viruses ...
Preface Operating System .......................................................... C-4 Environmental Spec ...................................................... C-4 Dimensions & Weight ..................................................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, card reader), TouchPad & Mouse, Audio & Printer. • Chapter 3 The computer’s power saving options.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find that this manual refers to the Windows 7 operating system.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide System Map: LCD Panel Open 1 Figure 1 - 2 LCD Panel Open Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 3 4 5 6 Use the key combinations to toggle power to the 3.
1 Quick Start Guide LED Indicators Icon Color Description The LED indicators on the computer display helpful information about the current status of the computer.
Quick Start Guide Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 3, on page 1 - 8 for full function key combination details. Function Keys NumLk & ScrLk Keys Play/Pause Key 3.75G/HSPA Module Power Toggle Key Numerical Keypad Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard.
1 Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed. Keys Function Keys Function Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle 3.
Quick Start Guide System Map: Front & Left Views Figure 1 - 4 Front & Left Views 1. 1 2. 3. 2 3 4 5 6 7 6 4. 5. 6. 7. 8 8. Multi-In-1 Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / RSMMC SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible MS (Memory Stick) / MS Pro / MS Duo LED Power Indicators DC-In Jack External Monitor Port RJ-45 LAN Jack HDMI-Out Port* 2 * USB 2.
1 Quick Start Guide Figure 1 - 5 Right & Rear Views 1. 2. 3. 4. 5. 6. Microphone-In Jack Headphone-Out Jack USB 2.0 Port Optical Device Drive Bay (see page 2 - 3 for CD/ DVD Device information) Security Lock Slot Battery System Map: Right & Rear Views 1 2 3 4 6 5 CD/DVD Emergency Eject Battery Information If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole.
Quick Start Guide System Map: Bottom View Figure 1 - 6 Bottom View 1. 2. 1 3. 3 3 4. 2 3 5 5. 6. 3 4 Battery Component Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover 3.75G USIM Card Cover (Optional) Speakers CPU 6 The CPU is not a user serviceable part. 6 Overheating Bottom Covers If your model includes the 3.75G option then a small cover 5 to enable you to access the module’s USIM card will be included (see “3.75G/HSPA Module” on page 7 - 15).
1 Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
Quick Start Guide Video Features You can configure display options from the Display control panel in Windows, and from the ATI Catalyst Control Center as long as the appropriate video driver is installed. For more detailed video information see “ATI Video Driver Controls” on page B - 1. To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. Click Start and click Control Panel. Click Display (icon) - In the Appearances and Personalization category.
1 Quick Start Guide Screen Resolution & ATI Catalyst Control Center - Win 7 1 2 3 4 5 Figure 1 - 8 - Screen Resolution & ATI Controls 1 - 14 Video Features 6
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 12) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
1 Quick Start Guide 1 - 16
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • Hard Disk Drive Optical (CD/DVD) Device Multi-in-1 Card Reader TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 12).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes: 1. 2. 3. 4. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times.
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Figure 2 - 4 Multi-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components TouchPad and Buttons/Mouse 2 The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. There are two TouchPad types available with the computer model series, and this is dependent upon your model’s design style. Operational Area Note that the TouchPad and buttons valid operational area is that indicated within the red dotted lines below.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you can configure the functions by double-clicking the touchpad driver icon on the taskbar.
Features & Components Gestures and Device Settings The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the TouchPad to perform specific actions to manipulate documents, objects and applications. You can configure the settings from the Device Settings tab in Mouse Properties: 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Mouse (Hardware and Sound). Click Device Settings (tab) and click Settings.
Features & Components Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion). 2 Figure 2 - 8 Scrolling Gesture Zooming The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality.
Features & Components Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Features & Components 2 Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Deck control panel . The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Features & Components Expert Mode will allow you to access more advanced configuration menus. 2 Figure 2 - 13 VIA HD Audio Deck (Expert Mode) See “HDMI Audio Configuration” on page B - 14 for more information on the audio settings for HDMI.
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Features & Components 2 Adding a Printer 2 - 15
Features & Components 2 2 - 16 Adding a Printer
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. Wake On LAN If you need your system setup to Wake ON LAN, then see the instructions in “Wake On LAN Setup” on page 8 - 18. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States 3 You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Taskbar Icon If the taskbar icon does not appear then click the taskbar arrow and select Customize. Energy Star Power Saving This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. If you want to enable Energy Star power saving then follow these instructions: 1. 2. 3. Right-click the taskbar icon (see sidebar). Select Power Conservation Modes.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 2 on page 3 - 5).
Power Management Conserving Battery Power 3 Wireless Hot Keys The computer’s wireless function keys will not function properly if Wireless is turned OFF in the Windows Mobility Center control panel. The wireless indicators may show that the WLAN module is powered on, however if wireless is OFF in the Mobility Center, the module will not be powered on. • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 3.
Power Management Proper handling of the Battery Pack 3 Caution • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive and click Install Drivers/Option Drivers (button). 4 Follow the instructions to install the driver. Alternatively click Start, navigate (Browse..) to the executable file and then follow the manual setup instructions. 1. 2. 3.
Drivers & Utilities Driver for Windows 7 Page # Video Page 4 - 5 LAN Page 4 - 6 TouchPad Page 4 - 6 CardReader Page 4 - 6 Hot Key Page 4 - 6 Audio Page 4 - 6 AMD AHCI Driver Page 4 - 7 Wireless LAN Module Page 7 - 2 PC Camera Module Page 7 - 8 3.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities New Hardware Found Driver Installation Procedure If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive and click Install Drivers (button).
Drivers & Utilities 4 LAN 1. Click 2.Install LAN Driver > Yes. 2. Click Install. 3. Click Finish. Hot Key 1. Click 5.Install Hotkey Utility > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart the computer. TouchPad 1. Click 3.Install Touchpad Driver > Yes. 2. Click Next. 3. Click the button to accept the license agreement and click Next. 4. Click Finish > Restart Now to restart the computer. Audio 1. Click 6.Install Audio Driver > Yes. 2. Click Next. 3.
Drivers & Utilities AMD AHCI Driver If you have enabled AHCI mode in the BIOS (see “SATA Mode Selection (Advanced Menu)” on page 5 - 9), and have not installed the AHCI driver at system installation, then you should do so now as per the instructions below: 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 4.Install AMD AHCI Driver > Yes. 4. Click Next > Install. 5. Click Finish > Finish to restart the computer. 6.
Drivers & Utilities 4 Windows Experience Index Optional Drivers After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experience Index: See the pages indicated for the driver installation procedures for any modules included in your purchase option. 1. Click Start, and click Control Panel. 2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index). 3. Click “Rate this computer”. 4.
Drivers & Utilities Wireless LAN Module 3.75G/HSPA Module See the introduction in “Wireless LAN Module” on page 7 - 2, and check the installation procedure. See the introduction in “3.75G/HSPA Module” on page 7 - 15, and check the installation procedure for the appropriate module. PC Camera Module See the introduction in “PC Camera Module” on page 7 - 7, and check the installation procedure. 4 Bluetooth Module A driver is only required for the Combination Wireless LAN & V3.0 Bluetooth.
Drivers & Utilities 4 4 - 10
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Utility The Phoenix Setup utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu 5 System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port 1/2 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Port 1/2. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu 5 Figure 5 - 3 Advanced Menu Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to enable/disable the WLAN Power Setting control. If enabled then the system will remember the last power status of the Wireless LAN module e.g. before a restart or shut down.
BIOS Utilities SATA Mode Selection (Advanced Menu) You can configure SATA (Serial ATA) control to operate in either IDE (native/ compatible) or AHCI (Advanced Host Controller Interface) modes from this menu. The SATA mode should be set to AHCI mode for this system (unless you are sure your hard disk can only operate in IDE mode). If you are unsure of the mode your hard disk supports contact your service center.
BIOS Utilities Security Menu Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu 5 - 10 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the PhoenixBIOS Setup Utility.
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the PhoenixBIOS Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the PhoenixBIOS Setup Utility cannot be modified in user mode. You can only set the user password after you have set the supervisor password.
BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu 5 When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot priority order. Item specific help on the right is available to help you move devices up and down the order.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu 5 Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
BIOS Utilities 5 5 - 14
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. 5. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 . Reverse the process to install the battery.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the discs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium. Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.
Upgrading The Computer 1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and loosen screws 1 & 2 . Remove the hard disk bay cover 3 .
Upgrading The Computer Hard Disk Screws & Cover 6 4. 5. 6. 7. Grip the tab and slide the hard disk in the direction of arrow 4 . Lift the hard disk out of the bay 5 . Remove the screw(s) 6 & 9 and the cover 10 . Reverse the process to install a new hard disk drive (do not forget to replace all the screws and covers). The hard disks and covers pictured here may appear slightly different from your model design (these designs are subject to change and upgrade without notice).
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Remove the hard disk (see page 6 - 4) Remove the screw at point 1 , and use a screwdriver to carefully push out the optical device at point 2 . Reverse the process to install the new device.
Upgrading The Computer Fan Cable & Cover 6 Make sure you reconnect the fan cable 5 before screwing down the bay cover. Note the information on replacing the RAM & CPU bay cover in “Cover Pins” on page 6 - 10. Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 3 for details of supported module types).
Upgrading The Computer 5. 6. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 7 & 8 ) in Figure 6 - 6. The RAM module will 9 pop-up, and you can remove it. 7 8 Figure 6 - 6 9 7. 8. 9. RAM Module Removal Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. The module’s pin alignment will allow it to only fit one way.
Upgrading The Computer Cover Pins 6 Note that this computer model has four cover pins. These pins need to be aligned with slots in the case to insure a proper cover fit, before screwing down the bay cover. 10. Press the module in and down towards the mainboard until the slot levers click into place to secure the module. 11. Replace the bay cover (see sidebar) and screws (make sure you reconnect the fan cable before screwing down the bay cover).
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • Wireless LAN Module • PC Camera Module • 3.75G/HSPA Module • AMD AHCI Driver • Bluetooth Module Important Notice If your purchase option includes both Wireless LAN and 3.75G/HSPA modules, then the appropriate antennas will be installed.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 3, on page 1 - 8/ Table 1 - 1, on page 1 - 6). Wireless LAN Module If you have included a 802.
Modules & Options Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then double-click an access point to connect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the taskbar menu (a list of options will appear allowing setting changes, and creating a new network).
Modules & Options 2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Modules & Options 5. 6. Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). , Security Enabled Networks You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center Wireless Hot Keys The computer’s wireless function keys will not function properly if Wireless is turned OFF in the Windows Mobility Center control panel. The 7 wireless indicators may show that the WLAN module is powered on, however if wireless is OFF in the Mobility Center, the module will not be powered on.
Modules & Options PC Camera Module Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 8) to toggle power to the PC Camera module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. There are a number of different camera modules available with this computer model series. You will have the appropriate application installed for your camera.
Modules & Options PC Camera Screen Refresh 7 The PC Camera module supports a frame rate of 12 fps. If you find that the screen refresh rate is subject to lag or stuttering, then reduce the window size, or adjust the Output Size and/or Color Space Compression. To reduce Output Size and/or Color Space Compression run the camera application, click Options and select Video Capture Pin. Adjust the settings from the appropriate pull-down menu. PC Camera Driver Installation 1.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (VIA High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules & Options Figure 7 - 5 Audio Setup for PC Camera Right-click 7 7 - 10 PC Camera Module
Modules & Options Camera Application The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page 7 - 9) and select Start Capture.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Frequency/Anti Flicker in Property Page (tab).
Modules & Options Zoom (not applicable to all camera modules) The camera program allows you to zoom the camera in and out (note the zoom function is not available in all camera model applications). Figure 7 - 7 1. 2. Run the camera application from the desktop shortcut. Go to Zoom and select Zoom Out/Zoom In. Zoom/Setting 7 Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture.
Modules & Options 3.75G/HSPA Module If you have included an optional 3.75G/HSPA (High Speed Packet Access) module (see “Communication” on page C - 3 for specification details) in your purchase option, you will have the appropriate application (Mobile Partner or BandLuxe HSDPA Utility) provided for your particular module. Follow the instructions on page 7 - 16 to install the USIM card (which will be provided by your service provider), and then install the application. Important Notice - 3.
Modules & Options Figure 7 - 8 1. 2. Turn off the computer, and turn it over and remove the battery (see page 6 - 3). Locate the 3.75G USIM card cover and loosen screw 1 , and then remove the USIM card cover 2 . USIM Card Cover Removal 1 Power Safety Warning 7 Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines).
Modules & Options 6. Lock the SIMLOCK by pushing it in the direction of the arrow in Figure 7 - 10 until it clicks into the lock position. Figure 7 - 10 SIMLOCK Lock 3.75G/HSPA Modules & System Wake Up Note that the 3.75G modules DO NOT support system wake up on 3.75G/HSPA modem activity. 3.
Modules & Options Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see Table 1 - 3, on page 1 - 8) to toggle power to the 3.75G/HSPA module. When the 3.75G/HSPA module is powered on, the indicator will briefly be displayed. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
Modules & Options Mobile Partner With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the Mobile Partner application. The Mobile Partner application allows you to directly access your HSPA internet service from the computer. Mobile Partner Application Installation 1. Enable power to the module by pressing the Fn + key combination (give the module about 10 seconds to power on - the on screen icon will indicate the module’s power status). 2.
Modules & Options Mobile Partner Application Mobile Partner Help To get help on Mobile Partner configuration and settings, click the Help menu and select Online Help or press F1. You will need to contact your service provider to obtain the exact details of how exactly to configure the settings on this page. Profile Management 1. 2. 3. 4. 7 5. Power on the 3.75G/HSPA module using the Fn + key combination.
Modules & Options Connecting to the Service Provider 1. 2. 3. 4. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Mobile Partner application from the Start menu (Start > Programs/ All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop . The software will run and you can select the Profile Name from the menu. Click Connect to begin the connection process. Figure 7 - 12 Connect 7 5.
Modules & Options 6. When the connection is successful you can move the cursor over the network icon in the taskbar to display the connection information. 7. You can then access the internet, download e-mail etc. as per any internet connection. While you are connected the indicators in the Mobile Partner window will display uploading and downloading icons and a network icon in the taskbar . Figure 7 - 14 Connected Taskbar Notification 7 8. 7 - 22 3.
Modules & Options 9. To disconnect click the Disconnect and select Disconnect. icon, or right click the taskbar icon Figure 7 - 15 Disconnect 7 10. The program will disconnect from the service provider. 11. The module will still be on, and you will need to press the Fn + to turn it off. key combination 3.
Modules & Options 12. If you click the Mobile Partner close icon a message will be displayed asking you to click OK to confirm the program exit and to terminate the connection. Figure 7 - 16 Exit Prompt 7 13. Exiting the program terminates the connection, but DOES NOT turn off the 3.75G/ key combination to turn off HSPA module, and you will need to press the Fn + the module (pay careful attention to this aboard aircraft - see “Wireless Device Operation Aboard Aircraft” on page 7 - 19). 14.
Modules & Options Text Messaging Service In addition to standard internet services you may also send and receive SMS text messages using the Mobile Partner program, if your service supports SMS. Reading SMS Messages 1. 2. 3. 4. An icon will blink at the bottom of the Mobile Partner interface to notify you of any new messages received. Click the Text icon in the Mobile Partner Interface. Select the Local > Inbox or SIM/USIM Card folder and select any message to read it.
Modules & Options AMD AHCI Driver If you have enabled AHCI mode in the BIOS (see “SATA Mode Selection (Advanced Menu)” on page 5 - 9), and have not installed the AHCI driver at system installation, then you should do so now as per the instructions below: 7 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 4.Install AMD AHCI Driver > Yes. 4. Click Next > Install. 5. Click Finish > Finish to restart the computer. 6.
Modules & Options Bluetooth Module There are two Bluetooth module options available for this computer. If your purchase option includes the Combination Wireless LAN & V3.0 Bluetooth module then install the driver as instructed overleaf (see “Bluetooth & WLAN Combo Settings” on page 7 - 29 for configuration instructions). If your purchase option includes a standard V2.
Modules & Options Bluetooth Combo Driver Installation High Speed Bluetooth Data Transfer 7 The Combination Wireless LAN & V3.0 Bluetooth module supports high speed (V3.0) data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer. Note this driver is required only for the combo Bluetooth and WLAN module only. 1.
Modules & Options Bluetooth & WLAN Combo Settings This information applies to the combo Bluetooth and WLAN module only. 1. 2. 3. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (menu heading). Bluetooth Module & Resuming From Sleep Mode The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state.
Modules & Options 4. 5. 7 Figure 7 - 18 General Settings 7 - 30 Bluetooth Module Click General Settings to change the computer name that other Bluetooth devices will see, and click the tickbox to Allow Bluetooth devices to find this computer Click OK to confirm the settings.
Modules & Options 6. 7. Click File Transfer Settings to Enable sharing of my files with other Bluetooth devices. Click OK to confirm the settings.
Modules & Options Bluetooth Networking Setup This information applies to the combo Bluetooth and WLAN module only. 1. 2. 3. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (see Figure 7 - 17 on page 7 - 29). 7 Figure 7 - 20 Network Settings 4. 5. 6. 7 - 32 Bluetooth Module Click Network Settings (make sure the Bluetooth module is powered on.
Modules & Options Bluetooth & WLAN Combo Module Configuration This information applies to the combo Bluetooth and WLAN module only. Bluetooth Module & Resuming From Sleep Mode Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. Press the Fn + F12 key combination to power on the Bluetooth module.
Modules & Options 3. You will then be presented with a menu of options to select from. 4. Click the appropriate button to connect to the device.
Modules & Options 5. 6. You may need to allow the connection from your device, and you will then need to provide a passcode from the device. You can then enter the passcode on the computer and click OK to establish the connection.
Modules & Options Add a Device Click Start, and click Control Panel and then click Devices and Printers (Hardware and Sound). Click Add a device to search for any available Bluetooth devices. 7 Bluetooth Module & Resuming From Sleep Mode Standard Bluetooth Configuration in Windows 7 Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation).
Modules & Options To Add a Bluetooth Device 1. 2. Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections. You can choose to have the computer create a pairing code for you, use the device’s existing pairing code or you can pair certain devices without using a code. Figure 7 - 25 3.
Modules & Options 4. Figure 7 - 26 Pairing Codes Pairing Code Example 7 Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing. 5. 6. 7.
Modules & Options To Change Settings for the Bluetooth Device 1. 2. • • Click the taskbar icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Bluetooth Help Change the name of the device (click Bluetooth, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3.
Modules & Options 7 7 - 40
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 6) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 11). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark. The system’s power saving features have timed-out.
Troubleshooting Problem Possible Cause - Solution The PC Camera module cannot be detected. The module is off. Press the Fn + F10 key combination in order to enable the module (see “Function/Hot Key Indicators” on page 1 - 8). Run the BisonCap program to view the camera picture. The Wireless LAN/Bluetooth/ PC Camera/3.75G/HSPA modules cannot be configured. The driver(s) for the module(s) have not been installed.
Troubleshooting Uninstalling the AMD AHCI Driver Uninstalling the AMD AHCI driver is a two part process. Follow the instructions below if you need to uninstall the diver for any reason. 1. 2. 3. 4. 5. 6. Go to the Windows control panel. Click Device Manager (Hardware and Sound > Devices and Printers). Click the arrow next to IDE ATA/ATAPI controllers to open the sub-menu. Double-click AMD SATA controller. Click Driver (tab) and click Uninstall. Click to select “Delete the driver software for this device.
Troubleshooting 7. 8. 9. 10. 11. 12. Click Yes to restart the computer. Click Restart Now to restart the computer again. After the computer has restarted return to the Windows control panel. Click Programs and Features (Programs). Click AMDSata and click Uninstall > Yes. Click Finish and close the control panel.
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Windows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver. 1. 2. 3. 4. 5.
Troubleshooting 6. 7. 8. Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 4 - Browse my computer.../Let me pick from... 9. Select Bluetooth Radios from the list.
Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list). 12. Select Windows Mobile-based device support from the Model list. 8 Make sure you select Microsoft Corporation Figure 8 - 6 - Select Device Driver 13.
Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.
Troubleshooting Wake On LAN Setup Wake On LAN is an Ethernet computer networking standard that allows a computer to be turned on or woken up by a network message. If you need to have your computer Wake On LAN you will need to enable Computer Management settings as follows. 1. 2. 3. 4. 5. Go the Windows control panel and double-click Administrative Tools (System and Security). Double-click Computer Management. Click Device Manager under System Tools, and click the arrow to the left of Network adapters.
Troubleshooting 6. 7. 8. 9. 10. Click Advanced (tab). Scroll down to the bottom of the Property menu and select “Wakeup from Shutdown”. Click to select Enabled from the drop-down Value menu. Click OK to close the menu. Close the Computer Management control panel.
Troubleshooting 8 8 - 20
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item RJ-45 LAN Jack Description This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.
Interface (Ports & Jacks) A A - 4
Appendix B: ATI Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 13. Video Card Options ATI Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 1. Click 1.Install Video Driver > Yes. 2. Click Next > Install (button). 3.
ATI Taskbar Icon The ATI Catalyst Control Center can be accessed as above or by double-clicking the icon in the taskbar (or by right-clicking the icon and selecting Catalyst Control Center). ATI Catalyst® Control Center Adjust the video settings from the ATI Catalyst® Control Center. 1. 2. 3. 4. Open the ATI Catalyst Control Center (see page 1 - 13). Click Advanced (button).
The ATI Catalyst® Control Center provides additional video configuration controls and tools which allow quick access to features such as display options, 3D Settings, color and Help menus etc. Adjust settings from the Graphics and Options menus at the top of the control panel. Help Menus Click the Help icon and select an option from the drop down menu. Press F1 to bring up Help for any currently selected page.
Function Keys You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Give the displays enough time to refresh. Other Applications B If you are using a third party application to play DVDs etc. you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation).
Display Modes Single Only one of your displays is used. Duplicate Duplicate simply shows an exact copy of the Main display desktop on the other display(s). This mode will drive multiple displays with exactly the same content, resolution, refresh rates and color quality etc. Extend Extend treats both connected displays as separate devices, and they act as a virtual desktop resulting in a large workspace. When a display is Extended, you can drag any icons or windows across to the other display desktop.
Detect Displays Click Detect Displays (button) to automatically update the attached display information. Configuring an External Display using the ATI CCC You can use the ATI Catalyst Control Center to configure any attached displays. 1. 2. 3. 4. 5. 6. 7. Attach your external display to the external monitor port/HDMI-Out port and turn it on. Open the ATI Catalyst Control Center. Select Desktops & Displays from the Graphics menu in the top left of the screen.
ATI CCC - Switching Display Modes 1. 2. 3. 4. 5. 6. 7. Attach your external display to the external monitor port/HDMI-Out port and turn it on. Open the ATI Catalyst Control Center. Select Desktops & Displays from the Graphics menu in the top left of the screen. Attached displays will appear in the lower part of the screen (click Detect Displays to find any attached displays that do not automatically appear). Right-click the attached external display icon and select Disable.
8. Select Duplicate or Extend from the menu. 9. Click Yes to accept the settings. 10. If you need to change the display mode then disable the external display and configure as outlined here. Figure B - 5 Desktops & Displays (Extend Mode) Right-click and select either Duplicate or Extend.
Configuring an External Display in Win 7 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port and turn it on. Go to the Screen resolution control panel (see “Video Features” on page 1 13). Click the Detect button. The computer will then detect any attached displays. Figure B - 6 Screen Resolution Multiple Displays (Win 7) B 5. You can configure the displays from the Multiple Displays menu.
6. Click Apply to save any setting changes. Figure B - 7 Screen Resolution Multiple Display Options (Win 7) B • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7. 1. 2. 3. 4. Attach your external display to the external monitor port and turn it on. + P key combination. Press the An on-screen menu will pop up. + P) to select the appropriate configuration from the Use the cursor keys (or menu, and press Enter to confirm the selection.
Theater Mode Theater Mode enables you to display video playback in full screen on a secondary monitor. Theater Mode can be configured from the Avivo™ Video > Theater Mode tab in the Graphics Settings Tree View pane.
PowerPlay™ PowerPlay™ in the ATI CCC allows you to set your graphics processor settings for higher performance or longer battery life.
HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. Configure the audio output as per the instructions below. 1. 2. 3. 4. Connect a device with HDMI support to the HDMI-Out port. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound), and click Playback (tab). Click to select the connected HDMI device and click Set Default (or right-click the icon and select Set as Default Device).
5. 6. Double-click the connected HDMI device (or right-click and select Properties) to adjust the HDMI settings from the control panel tabs. Click OK to close the control panel (see notes overleaf).
HDMI Notes Other Applications If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation). • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processor Display Storage AMD® Athlon™ x2 Dual Core Processor: QL62 (2.0GHz) 65nm (65 Nanometer) Process Technology, 1MB L2 Cache & 667MHz FSB - TDP 35W - (638-pin) Micro--PGA 15.6” (39.62cm) 16:9 HD (1366 * 768) TFT LCD One Changeable 12.7mm(h) Super Multi Optical Device Drive (CD/DVD) with SATA Memory Interface One Changeable 2.5" 9.5 mm (h) HDD with SATA (Serial) Interface Package - Socket-S1G2 AMD® Athlon™ Single Core Processor: QI46 (2.
Specifications Interface Slots Communication Three USB 2.0 Ports One External Monitor Port One HDMI-Out Port One Headphone-Out Jack One Microphone-In Jack One RJ-45 LAN Jack One DC-In Jack Two Mini-Card Slots with PCIe (Slot 1) & USB (Slot 2) interface: 3.75G Module: UMTS/HSPDA-based 3.
Specifications Security Security (Kensington® Type) Lock Slot BIOS Password Operating System Windows® 7 Design Feature Options IMR (Injected Molded Resin) LCD Back Covers Texture LCD Back Covers Environmental Spec Temperature Operating: Non-Operating: Relative Humidity Operating: Non-Operating: 5°C - 35°C -20°C - 60°C 20% - 80% 10% - 90% Dimensions & Weight C 374mm (w) * 250mm (d) * 14.3 - 34.1mm (h) 2.5 kg with 48.
