INSTALLATION INSTRUCTIONS XCB1U (Shown installed to CPA Series extension column as example only) Back-to-Back Large Flat Panel Ceiling Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description XCB1U
XCB1U Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions XCB1U DIMENSIONS 15.75 400.0 MAX MOUNTING PATTERN HEIGHT 31.92 810.
XCB1U Installation Instructions LEGEND Tighten Fastener Adjust Apretar elemento de fijación Ajustar Befestigungsteil festziehen Einstellen Apertar fixador Ajustar Serrare il fissaggio Regolare Bevestiging vastdraaien Afstellen Serrez les fixations Ajuster Loosen Fastener Remove Aflojar elemento de fijación Quitar Befestigungsteil lösen Entfernen Desapertar fixador Remover Allentare il fissaggio Rimuovere Bevestiging losdraaien Verwijderen Desserrez les fixations Retirez Phillip
Installation Instructions XCB1U TOOLS REQUIRED FOR INSTALLATION 3/32" (included) 1/8" (included) 5/32" (included) M5 (included) #2 1/2" or 13mm PARTS [Interface Bracket Hardware Kit] (2 bags total - quantities listed per bag) A (8) M4x16mm E (6) M5x20mm I (6) M8x20mm B (6) M4x20mm F (6) M5x25mm J (6) M8x30mm L (8) .750x.323x.250 M (8) .750x.344x.
XCB1U Installation Instructions INSTALLATION WARNING: FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS COMPONENT CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.
Installation Instructions XCB1U Attaching Mount to CPA Extension Column CAUTION: WATCH FOR PINCH POINTS! Do not place fingers between moveable parts. 1. Check inside of mount housing for screws encroaching in extension column area. 2. Loosen two 5/16 x 3-1/2" button head cap screws on end of housing until they no longer extend into the extension column area inside housing, but do NOT remove the screws completely.
XCB1U 2. Installation Instructions Align the center of the interface bracket (DD) with center of screen. (See Figure 6) NOTE: The diamond-shape hole in the bracket corresponds to the center of the mount. (L or M) 2 (N) 3 2 Center of bracket (DD) 3 (A-K) 3 Figure 6 (Near mounting rail not shown for clarity) Latch mechanism WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display.
Installation Instructions XCB1U Adjustments CAUTION: Watch for pinch points! Do not place fingers between moveable parts. IMPORTANT ! : Always use two hands (one at bottom of display and one at top of display) to adjust ceiling mount. 3 Roll Tilt The ceiling mounts allow up to 3° roll each direction. 1. 5 friction bolt (X) Turn the roll adjustment bolt(s) in the direction necessary for the desired roll. (See Figure 9) 6 NOTE: Each roll adjustment bolt controls the roll on its side of the mount.
XCB1U Installation Instructions OPTIONAL: Security 1. OPTIONAL: Add padlock (not included) to each interface bracket to lock displays to ceiling mount.
Installation Instructions XCB1U 11
XCB1U Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002445 Rev00 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 11/13 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
