INSTALLATION INSTRUCTIONS Interactive Short-Throw Upgrade Kit Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description WM2I
WM2I Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions WM2I LEGEND Tighten Fastener Phillips Screwdriver Apretar elemento de fijación Destornillador Phillips Befestigungsteil festziehen Kreuzschlitzschraubendreher Apertar fixador Chave de fendas Phillips Serrare il fissaggio Cacciavite a stella Bevestiging vastdraaien Kruiskopschroevendraaier Serrez les fixations Tournevis à pointe cruciforme Loosen Fastener By Hand Aflojar elemento de fijación A mano Befestigungsteil lösen Von Hand Desapertar fixador Com a mão
WM2I Installation Instructions REQUIRED TOOLS FOR INSTALLATION 5/32" (security) #2 PARTS B (1) [Interactive cover] A (1) [Cover - top] D (4) [Stylus replacement tips] G (1) [AAA battery] C (1) [Stylus] E (1) [Stylus wrist strap kit] K (1) 5/32" (security) H (1) [Interactive USB cable -15 ft.
Installation Instructions WM2I ASSEMBLY AND INSTALLATION The WM2I is designed to replace the existing cover(s) on the WM210, WM220, WM230 and WM240, and to convert the existing short throw mount to a Chief Interactive Mount (WM2XXSI). The WM2XXSI works with standard projectors and Windows® and Macintosh® computers.
WM2I • 1. 2. Installation Instructions Split Mount Covers Remove two Phillips pan head screws from upper cover. (See Figure 4) Raise upper cover away from the mount. (See Figure 4) 1 2 Route cables 2 Cartridge Cartridge (B) Figure 6 3. 1 x2 Raise the interactive cover (B) containing cartridge and attach to wall mount using two 8-32 x 3/8" Phillips pan head screws (M) [or using two 8-32 x 3/8" security button head screws (L)]. (See Figure 7) Figure 4 3. 3 Remove lower cover from mount.
Installation Instructions 4. WM2I Lower the upper cover (A) onto the wall mount and interactive cover (B), and fasten with two 8-32 x 3/8" Phillips pan head screws (M) [or use two 8-32 x 3/8" security button head screws (L)]. (See Figure 8) NOTE: Be sure cables and cords are not pinched between upper and lower covers. Connecting Chief Interactive Mount NOTE: Follow instructions in the Quick Start Guide (J).
Installation Instructions WM2I Environmental Interference Guide Ultrasound Reflections General proximity guideline: A distance of 12 feet (approximately 4 meters) between the motion sensor and the eBeam receiver will normally allow good performance with the maximum board size. (See Figure 10) Interference can be reduced by reducing the size of the projection area.
Installation Instructions WM2I WM2XXSI Placement and Projection Area Constraints (See Figure 11) • • • • There should be a minimum distance of 12 inches between the base of the dual mount and the top of the projection image. The distance between the base of the dual mount and the bottom corner of the projection image (both right and left) should be less than or equal to 110 inches. The projection image should start a minimum of 1 inch from the base of the top frame of the whiteboard.
WM2I 10 Installation Instructions
Installation Instructions WM2I 11
WM2I Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002063 Rev02 2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 12/11 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
