INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation WM-110 WM-120 WM-130 Single Stud Short Throw Wall Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description WM110S-120S-130S
WM110S-120S-130S Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions WM110S-120S-130S LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro
WM110S-120S-130S Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1/2" (12.7mm) 3/8" (9.5mm) 7/32" (5.6mm) 5/32" (included) (security) #2 1/2" (12.
Installation Instructions WM110S-120S-130S Site Requirements WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation.
WM110S-120S-130S Installation Instructions ASSEMBLY AND INSTALLATION The WM1XXS single stud short throw wall mount can be mounted to concrete, concrete block, 2" x 4" wood studs or steel studs.
Installation Instructions 5. WM110S-120S-130S Install three 5/16 x 2-1/2" hex head lag screws (E) through three 5/16" washers (F), inner holes of mounting bracket and into drilled holes. (See Figure 4) (B) 3 x3 4 5 (E) x 3 (F) x 3 Steel stud Figure 5 5. Hold metal channel on anchor (J) flat alongside plastic straps and slide channel through hole.
WM110S-120S-130S 8. 9. Snap off plastic straps on anchor at wall by pushing side to side, snapping off straps level with flange of plastic cap. (See Figure 8) Repeat Steps 5 through 8 for each mounting hole. Installation Instructions (side view) Steel Stud Drywall (side view) (G) x 3 Steel Stud Drywall (H) x 3 11 8 Plastic Cap Plastic Straps Wall bracket Anchor Metal Channel Anchor Metal Channel Figure 8 10.
Installation Instructions WM110S-120S-130S 3 3 (S) x 2 4 (U) x 2 (T) x 2 (A) 2 (C) (Y) x 2 (B) Figure 11 Installing Mount Covers 1. Raise lower cover (D) up to WM1XXS.
WM110S-120S-130S Installation Instructions (bottom view) RPA RPM mounting plate RSA RSM RSM 2 (W) x 4 Figure 16 3. Figure 14 Install interface and projector to RSM according to RSM installation instructions. RPA Installation RPM Installation 1. Line up mounting holes on RPM mount with corresponding holes on projector mounting plate. (See Figure 14) 2. Install four 1/4-20 x 1-1/2" Phillips pan machine screws (V) through RPM holes and into projector mounting plate. (See Figure 15) 1.
Installation Instructions WM110S-120S-130S level. • • 4. Tighten two bolts (one bolt on either side of pitch adjustment screw). (See Figure 20) 5. Tighten two 5/16 x 1/2" hex head screws (S) (one on each side of mounting bracket). (See Figure 20) mounting plate RSA Pitch adjustment screw Lower (R) x 4 2 Raise Figure 18 3. Turn clockwise to raise mounting level. Turn counterclockwise to lower mounting level.
WM110S-120S-130S Installation Instructions 3. (projector not shown) (Optional) Cables may be tied to inside of WM1XXS front cover using cable ties (not included). Route cables near front cover and wrap cable tie through slots on front cover and around cables. (See Figure 23) cable tie (not included) 1 [Small cable cover] 1 [Large cable cover] Figure 21 2. 3 Route projector cable(s) under mount cover and through short throw projector arm tunnel.
Installation Instructions 5. WM110S-120S-130S Return outer covers to the mount following instructions in Installing Mount Covers section. 3. Remove two bolts holding stop bracket in place on underside of short throw projector mount. (See Figure 27) Extension Adjustment 1. Loosen two bolts holding stop bracket in place on underside of short throw projector mount. (See Figure 25) 2. Adjust mount to desired extension length. (See Figure 25) 3.
WM110S-120S-130S 5. Installation Instructions (Optional) Remove projector from WM1XXS according to projector interface instructions. NOTE: For most projectors, it will be necessary to remove Adapter plate projector prior to install four security screws to projector bracket. For ease of installation, it is recommended to remove projector prior to performing the following steps. 6. Plastic spacer Remove one of four bolts from adapter plate.
Installation Instructions WM110S-120S-130S 15
WM110S-120S-130S Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8802-002086 Rev01 2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 06/11 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No.
