INSTALLATION INSTRUCTIONS Extended Interactive Whiteboard Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description WBM2E
WBM2E Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions WBM2E DIMENSIONS 13.56 344.
WBM2E Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestigin
Installation Instructions WBM2E TOOLS REQUIRED FOR INSTALLATION 7/16" 1/2" 1/2" 1/8" - wood stud 1/4" - concrete, brick 5/32" (included) 5/32" (included) PARTS B (4) [AF6 toggler] A (4) 1/4" F (2) 1/4-20 x 3/8" E (1) 5/32" C (4) 1/4-20 x 2-1/2" G (4) [Isolation washer] H (4) 1/4-20 x 1" D (2) [Upright assembly] J (4) .500x.320x.425 S (2) .4 x .255 x .
WBM2E Installation Instructions ASSEMBLY AND INSTALLATION The WBM2E will allow an interactive whiteboard to be installed over an existing chalkboard or whiteboard. The WBM2E may be installed in the default position which installs in front of preexisting chalk or marker trays, OR in the low profile position which installs on the top of preexisting chalk or marker trays. (D) Assembly 1. Remove and SAVE four Phillips screws from bottom of upright assembly (D). (See Figure 1) 2.
Installation Instructions WBM2E 1. Slide wall brackets along wall assembly (K). (See Figure 3) 2. Tighten button head cap screw on each wall bracket to secure wall brackets to wall assembly. (See Figure 3) 3 4 6 7 (A) x 4 1 2 Wall brackets x2 1 5 8 (C) x 4 (K) (K) Figure 4 (side view) Figure 3 NOTE: Proceed to the Installing to a Wood Stud Wall section, or the Installing to a Concrete, Concrete Block or Clay Brick Wall section, as appropriate. Installing to a Wood Stud Wall 1.
WBM2E Installation Instructions 3. Drill one 1/4" x 2-3/4" pilot hole at each marking. (See Figure 5) 4. Install a toggler (B) into each pilot hole using a hammer. (See Figure 5) 5. 3. Fasten upright in place using one 1/4-20 x 3/8" button head cap screw (F) and one .4"x.255"x.0625" nylon spacer (S). (See Figure 7) 4. Repeat for other side of wall extrusion. Use two 1/4-20 x 2-1/2" lag bolts (C) and two 1/4" flat washers (A) to attach wall assembly (K) to anchors in wall. (See Figure 5) 6.
Installation Instructions WBM2E 7. Vertical Adjustment 1. Loosen one button head cap screw with spacer at top of each upright assembly (D). (See Figure 9) 2. Unhook whiteboard from wall assembly (K). (See Figure 9) Tighten button head cap screw with spacer (loosened in Step 1) at top of each upright assembly to fasten upright assemblies (D) into place.
WBM2E Installation Instructions Concrete, Concrete Block or Clay Brick Wall 1. Mark the wall through the fixed wall leg (N) on each upright assembly (D). (See Figure 13) Drywall Plastic Straps 2 1 (N) 3 (PD) x 2 Figure 15 3 4. Holding plastic straps on anchor (PD), pull anchor away from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud. (See Figure 16) 5. Slide plastic cap on anchor (PD) towards wall until flange of cap is flush with wall.
Installation Instructions 7. Repeat Steps 3 through 6 for remaining mounting hole. 8. Place fixed wall legs (N) over anchors and align mounting slots with holes in anchors. (See Figure 18) 9. WBM2E (L) Place 1/4" flat washer (PC) onto 1/4-20 x 1-3/4" Phillips pan head screw (PA). 1 (K) 10. Insert Phillips pan head screw (PA) with flat washer (PC) through mounting slot in fixed wall leg and into anchor (PE) and tighten until flush against fixed wall leg.
WBM2E Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002275 Rev00 2012 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 11/12 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
