INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Large Swing Arm Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description TS525TU
TS525TU Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions TS525TU DIMENSIONS 39.1 1.5 DISTANCE FROM WALL WITH INTERFACE [35.6] 1.4 WITHOUT INTERFACE 550.28 21.664 821.19 32.330 MAX. WIDTH MAXIMUM WEIGHT CAPACITY = 125 lbs. (56.7 kg) 800 31.496 MAX. HORIZONTAL PATTERN 406.40 16.000 15 MAX TILT 17.46 .688 7.00" [177.8] LEFT/RIGHT ADJUSTMENT 12.50 .492 651.9 25.67 MAX EXTENSION FROM WALL COLLAPSED VIEW 235.64 9.277 SCREEN CENTER 100 X 100 200 X 200 PATTERNS INCLUDED 63.50 2.500 400 15.748 MAX. VERTICAL PATTERN 473.08 18.
TS525TU Installation Instructions LEGEND 4 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Beve
Installation Instructions TS525TU TOOLS REQUIRED FOR INSTALLATION concrete only 13/64" (5.1mm) - wood studs 3/8" (10mm) - concrete 1/2" (12.
TS525TU Installation Instructions Assembly And Installation Install Wall Plate to Wall - Wood Studs WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.
Installation Instructions TS525TU Install Wall Plate to Wall - Hollow Concrete Block or Poured Concrete (Important!- Read warnings below for drywall restrictions!) WARNING: Failure to provide adequate structural strength 10 for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment.
TS525TU Installation Instructions 4. Install two concrete anchors (G) into two drilled holes. (See Figure 7) 5. Loosely attach wall rail (N) to wall by installing two 5/16- 2 1/2 flange head lag screws (F) into concrete anchors (G). (See Figure 7) center of wall rail 11 IMPORTANT ! : Use a level to make sure wall rail (N) is level when mounted to the wall! 6. Place two installation spacers (H) over two 5/16 x 2 1/2" flange head lag screws (F). (See Figure 7) 7.
Installation Instructions TS525TU 15. Loosely install two 5/16 x 2 1/2" flange head lag screws (F) through lower wall rail on main assembly and into concrete anchors. (See Figure 10) 16. Place two installation spacers (H) over two flange head lag screws (F). (See Figure 10) 17. Tighten two screws (F) to secure main assembly (M) to wall.
TS525TU Installation Instructions Install Interface Bracket to Display IMPORTANT ! : If the displays hole pattern size is 100mm x100mm, 200mm x 200mm or 100mm x 200mm, the display can be mounted directly to the faceplate and the interface bracket DOES NOT need to be installed! Proceed to Install Display section. 1. (A-C) x4,x6,x8 or 6 2 (D) x4 (P) 4 Lay display face down on protective surface.
TS525TU Installation Instructions 8. 8 (W) x 4 Connect top interface support (R) to uprights (P and Q) using four #10-24 x 1/2" button head cap screws (W). (See Figure 14) NOTE: If possible install screws diagonally across from each (R) other in order to provide maximum support in Steps 8 and 9. 9. Connect bottom interface support (S) to uprights (P and Q) using four #10-24 x 1/2" button head cap screws (W). (See Figure 14) 10 10.
TS525TU Installation Instructions Installing Display Without Interface Bracket (100x100, 200x200 or 100x200) (200 x 200 shown) CAUTION: Using screws of improper diameter may damage your display! Proper screws will easily thread into display mounting holes. 1. (K) x 2 with (A) or (J) x 2 with (B) Select screw diameter by examining hardware (A-D) (4mm, 5mm, 6mm or 8mm) and comparing with mounting holes on display.
Installation Instructions TS525TU Cable Management 1. Make all cable connections to display. 2. Open cable management covers on upper and lower swing arms. (See Figure 19) 3. Route cables on top of upper arm. (See Figure 19) 4. (Optional) Use cable ties (not included) to secure cables to upper arms by threading ties around cable and through cable tie holes on arms. (See Figure 19) 5. Close upper cable management cover. (See Figure 19) 6. Route cables under lower portion of swing arm.
TS525TU Installation Instructions Leveling Friction Adjustment Lateral Shift Adjustment 1. 1. Remove wall rail covers (N) to expose lateral shift adjustment screws on wall rails. 2. Loosen four lateral shift adjustment screws. (See Figure 24) 3. Loosen two lower lag screws securing lower rail to the wall. (See Figure 24) 4. Slide mount laterally to desired mounting position. (See Figure 24) 5. Tighten two lower lag screws. (See Figure 24) 6. Tighten four lateral shift adjustment screws.
Installation Instructions Arm Tension Adjustment 1. Use 1/4" hex key (AA) to adjust arm tension at any of the four arm tension adjustment points. (See Figure 25) not adjustable with hex key TS525TU Install Interface Bracket Adhesive Covers (Optional) If the interface bracket was required to install display to mount, adhesive covers may be used to cover the holes on the interface bracket in order to improve the appearance. 1. Use two long adhesive strips (CC) to cover vertical uprights.
TS525TU Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8805-002008 REV 09 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 01/13 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
