INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Medium Dual Swing Arm Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description TS218SU
TS218SU Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions TS218SU DIMENSIONS 2.65 67.3 PAN MOTION 90 LEFT/RIGHT 12° MAX TILT SCREEN 18.0 456.2 MAXIMUM EXTENSION 1.50 38.1 MINIMUM FROM WALL 1.00 25.4 SCREEN CENTER TO TOP LAG BOLT 2.58 65.5 CENTER 8.12 206.1 .265 6.73 - .50" [12.
TS218SU Installation Instructions LEGEND 4 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Beve
Installation Instructions TS218SU TOOLS REQUIRED FOR INSTALLATION concrete only 1/8" - wood studs 8mm - concrete 7/16" (11.
TS218SU Installation Instructions Assembly And Installation 8. Drill two 1/8" holes at locations marked in Step 6. (See Figure 2) Install to Wall 9. Hang main assembly (J) back onto wall. Install Main Assembly to Wall - Wood Studs 10. Install two 1/4 x 2 1/2" lag bolts (F) into holes drilled in Step 8 to secure mount to wall. (See Figure 2) WARNING: Failure to provide adequate structural strength 11. Tighten all three lag bolts (F) to fully secure mount to wall.
Installation Instructions TS218SU Install Main Assembly to Wall - Hollow Concrete Block, Poured Concrete or Clay Brick WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. 4.
TS218SU Installation Instructions Display Installation (configuration 2 shown) Install Interface Brackets to Faceplate (if necessary) IMPORTANT ! : If the displays hole pattern size is 100mm x 100mm, 200mm x 100mm or 200mm x 200mm, the display can be mounted directly to the faceplate and the interface brackets DO NOT need to be installed! Proceed to Attach Faceplate to Display Without Interface Brackets Section. 1.
Installation Instructions TS218SU Attach Faceplate to Display Using Interface Brackets 1. (configuration 2 shown) Lay display face down on protective surface. (A-C) x4 or 5 (D) x4 (E1) or (E3) x 4 CAUTION: Using screws of improper diameter may damage your display! Proper screws will easily thread into display mounting holes. 2. Select screw diameter by examining hardware (A-D) (4mm, 5mm, 6mm or 8mm) and comparing with mounting holes on display. (See Figure 8) 3.
TS218SU Installation Instructions Attach Faceplate to Display Without Interface Brackets (100x100 or 200x200 or 100x200 hole patterns) 1. Lay display face down on protective surface. 2. Determine hole configuration to be used on faceplate. (See Figure 10) 6. Use selected screws and spacers to connect interface brackets to back of display.
Installation Instructions TS218SU (N) (M) (H) 1 (M) x 2 pitch bracket 2 (N) x 2 Figure 12 Install Display to Main Assembly Wall Cover Installation WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached does not exceed 75 lbs (34 kg).
TS218SU Installation Instructions Cable Management Height Adjustment 1. Make all cable connections to display. 2. Open cable management covers on upper and lower swing arms by unhinging center tabs and lifting covers to the open position. (See Figure 14) The TS218SU may be adjusted 1/2" up or down after installation to the wall. 1. Remove display from main assembly. 2. Remove top and bottom covers (K and L) to expose height adjustment screws. 3.
Installation Instructions TS218SU Roll Adjustment Arm Tension Adjustment NOTE: If flange nuts (N) were not fully tightened when display 1. was installed, the roll may be adjusted manually without loosening the nuts further. 1. Loosen two flange nuts (N) to decrease roll tension. (See Figure 17) 2. Adjust roll position of display as desired. (See Figure 17) 3. Tighten two flange nuts (N) to increase roll tension, if desired.
TS218SU 14 Installation Instructions
Installation Instructions TS218SU 15
TS218SU Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8832-002074 REV 04 2012 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 04/12 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
