INSTALLATION INSTRUCTIONS Truss Tilt Adjustable Mount TPP Series
TPP Series Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions TPP Series DIMENSIONS DIMENSIONS: INCHES 3
TPP Series Installation Instructions LEGEND 4 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Measure Drill Hole Medir Perforar Messen Bohrloch Medir Fazer furo Misurare Praticare un foro Meten Gat boren Mesurer Percez un trou Phillips Screwdriver Adjust De
Installation Instructions TPP Series TOOLS REQUIRED FOR INSTALLATION 7/16" 9/16" #2 7/16" 9/16" 5/32" (included) REQUIRED PARTS (NOT INCLUDED) [TPK Truss/Pole Kit] (example) TPK-3 or TPK-4 or TPK-5 X4 X8 X8 PARTS Faceplate Backplate Tilt-adjustable plate A (1) [TPP mount assembly] B (1) [PSB Interface bracket kit] (example) C (1) (5/32") 5
TPP Series Installation Instructions INSTALLATION Horizontal Installation 1. WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.
Installation Instructions 3. TPP Series Re-attach backplate to tilt-adjustable plate/faceplate assembly using the four hex head cap screws (inserted from inside the tilt-adjustment plate). (See Figure 4) Vertical Installation The TPP assembly ships configured for vertical pole mounting. 1. Horizontal Configuration Securely anchor TPP backplate to vertical poles using Chief TPK accessory clamps (not included) following instructions included with TPK kit.
TPP Series Installation Instructions 1. Attach PSB interface bracket (B) to display using the instructions included with the PSB package. 2. Using two people, slide display with attached interface bracket (B) down over the four slots in the faceplate of the TPP (A). Make sure all four mounting buttons engage all four Q-Latch slots in the TPP (A). (See Figure 8) Latching flag (on other side) 2 4.
Installation Instructions TPP Series Removing the Display (Optional) Locking Angle Tilt Holes The TPP can be tilted up to 15 degrees, and features three holes used to set specific tilt (0°, 5° and 10°). 1. Loosen tilt adjustment screws, adjust to desired tilt, and tighten tilt adjustment screws. (See Figure 11) 2.
TPP Series Installation Instructions (Optional) Security Lock A hole is provided in the Q-Latch flag and faceplate to accommodate the insertion of a padlock (not included) or similar locking device. 1. Insert padlock through lower hole in Q-Latch flag and face plate.
Installation Instructions TPP Series 11
TPP Series Installation Instructions USA/International Chief, a products division of Milestone AV Technologies 8800-002566 Rev00 2014 Milestone AV Technologies www.chiefmfg.com 04/14 Europe Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
