INSTALLATION INSTRUCTIONS Small Swivel Table Stand Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description STS1
STS1 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions STS1 LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging
STS1 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/32" (included) 5/32" (included) 5/16" (7.9mm) PARTS B (1) [Wire cover] A (1) [Table stand] C (1) [Top cap] F (4) 1/4" D (1) [Base cable plug] G (4) 1/4" E (4) 1/4-20 x 3-1/4" J (1) [Array hardware] K (1) 3/32" JA (4) M4 x 12mm L (1) 5/32" 4 JB (4) M4 x 20mm JD (4) .500 x .194 x .750 JE (4) .500 x .194 x .
Installation Instructions STS1 INSTALLATION Site Preparation WARNING: EXCEEDING WEIGHT CAPACITY CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the combined weight of all components attached to the STS1 up to (and including) the display does not exceed 30 lbs (13.6 kg). 270° 270° 180° 180° WARNING: TURNING DISPLAY CAN CAUSE DAMAGE TO SURROUNDING OBJECTS.
STS1 5. Installation Instructions Attach STS1 to mounting surface using 5/32" hex key (L) and four 1/4-20 x 3-1/4" button head cap screws (E), four flat 1/4" flat washers (G), four 1/4" fender washer (H), and four 1/4" Nylock nuts (F). (See Figure 4) 6. Lower STS1 base cover. (E) x 4 5 Cable Management 1. Run power cables from display to the back of the STS1. 2. Lay power cables down back and through bottom of STS1, and through mounting surface. 3.
Installation Instructions STS1 Adjustments • Rotating Display 1. The display may be rotated up to 90° on the STS1 head by using the 5/32" hex key (L) to loosen the fastener, rotating the head in either direction, and tightening the fastener. (See Figure 7) Head Assembly Hex Fastener 4. Loosen the head assembly hex fastener using the 5/32" hex key (L) to decrease tension. (See Figure 8) 5. Adjust STS1 head as required. 6. Tighten head assembly hex fastener to increase tension.
STS1 Installation Instructions USA/International Europe Chief, a products division of Milestone AV Technologies 8804-002015 Rev02 2014 Milestone AV Technologies www.chiefmfg.com 04/14 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
