INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Single Stud Wall Mount Accessory Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description WMA1S
WMA1S Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions WMA1S LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestigin
WMA1S Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 1/2" (12.7mm) 5/32" (included) (security) 1/2" (12.7mm) steel stud 3/8" (10mm) concrete and concrete block 7/32" (5.
Installation Instructions WMA1S Site Requirements WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation.
WMA1S Installation Instructions ASSEMBLY AND INSTALLATION The WMA1S single stud wall mount accessory can be mounted to concrete, concrete block, 2" x 4" wood studs or steel studs. (B) Installing Mounting Bracket WARNING: ELECTRICAL SHOCK HAZARD! CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of electrical wires and cables before cutting, drilling, or installing fasteners.
Installation Instructions 5. WMA1S Install three 5/16 x 2-1/2" hex head lag screws (C) through three 5/16" washers (D), inner holes of wall bracket (B) and into drilled holes. (See Figure 4) 5. Hold metal channel on anchor (G) flat alongside plastic straps and slide channel through hole. (See Figure 6) Drywall Plastic Straps 5 5 (C) x 3 (D) x 3 (G) x 3 Figure 6 (B) 6.
WMA1S 8. 9. Installation Instructions Snap off plastic straps on anchor at wall by pushing side to side, snapping off straps level with flange of plastic cap. (See Figure 8) Repeat Steps 5 through 8 for each mounting hole. Installation to Wall Bracket 1. Lift WMA1S assembly (A) up to wall bracket (B) and hook upper plate over upper notches on bracket. (See Figure 10) 2. Slide lower plate into lower notches on bracket.
Installation Instructions WMA1S PROJECTOR INSTALLATION Installing Mount Covers 1. Raise lower cover (X) up to WMA1S. (See Figure 12) WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight attached to the wall mount accessory up to (and including) the attached component(s) does not exceed: • • • Installed in steel stud: 50 lbs (22.7 kg) Installed in 2" x 4" wood stud: 150 lbs (68.
WMA1S Installation Instructions Removing Mount Covers 1. Remove two #8 x 1/2" Phillips pan tapping screws (U) and two #10 x 1" Phillips pan tapping screws (V) to free top cover (W) and expose pitch adjustment screw. (See Figure 15) 2. 4 Remove lower cover (X) from WMA1S. (See Figure 15) Raise (V) x 2 1 Pitch adjustment screw Lower 5 (U) x 2 1 or 6 (W) 1 3 7 (N) x 2 (X) Figure 16 2 Cable Management (Optional) 1.
Installation Instructions 3. WMA1S Route projector cable(s) under mount cover and through WMA1S arm. (See Figure 18) 5 Figure 18 4. (Optional) Cables may be tied to inside of WMA1S front cover using cable ties (not included). Route cables near front cover and wrap cable tie through slots on front cover and around cables. (See Figure 19) 4 Cable tie (not included) (bottom view) Figure 20 Extension Adjustment 1. Loosen two bolts holding stop bracket in place on underside of WMA1S.
WMA1S Installation Instructions Security Screw Installation (Optional) 1. Remove two #8 x 1/2" Phillips screws (U) and two #10 x 1" Phillips screws (V) from top and lower covers. (See Figure 22) 2. Install two 8-32 x 1/2" buttonhead security screws (H) and two 10-24 x 1" buttonhead security screws (L) into top and lower covers. (See Figure 22) 1 1 Sliding nuts location (V) x 2 (U) x 2 Stop bracket 2 (L) x 2 4 2 (J) x 2 (H) x 2 Figure 24 5. Figure 22 3.
Installation Instructions WMA1S 7. Install one 1/4-20 x 3/4" button head security screw (K) into hole vacated by removing bolt in Step 6 and into plastic spacer. (See Figure 26) 8. Repeat Steps 6-7 for remaining three bolts one bolt at a time. WARNING: It is important to replace adapter plate bolts ONE AT A TIME or adapter plate could fall from mount during installation! Plastic spacer Adapter plate 7 (K) x 4 (one at a time) Figure 26 9.
WMA1S 14 Installation Instructions
Installation Instructions WMA1S 15
WMA1S Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8802-002083 Rev01 2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 06/11 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No.
