Installation instructions

ManualsBrandsChief ManualsTVs & monitorsPXRUB

INSTALLATION INSTRUCTIONS

Automated Wall Mount

This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if

not installed and used in accordance with the instructions, may cause harmful interference to radio or television communications. However, there is no guarantee that

the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment to an outlet on a circuit other than that to which the receiver is connected

Consult the dealer or an experienced radio/TV technician for help.

PXR

Summary of content (32 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Automated Wall Mount This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules.
PAGE 2
PXR Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
PAGE 3
Installation Instructions PXR TABLE OF CONTENTS DISCLAIMER . . . . . . . . . . . . . . . . . . . . . . . . . 2 TABLE OF CONTENTS . . . . . . . . . . . . . . . . . 3 DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 4 LEGEND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 TOOLS REQUIRED FOR INSTALLATION . . 7 SET-UP AND CONFIGURATION WITH DISPLAY ATTACHED . . . . . . . . . . . . . . 21 Running LEARN MODE . . . . . . . . . . . . . 21 Saving a Preset . . . . . . . . . . . . . . . . .
PAGE 4
PXR Installation Instructions DIMENSIONS 20.45 519.5 6.36 BACK 5.47 17.44 442.9 8.06 9.19 233.4 CENTER OF INTERFACE TO MOUNTING HOLES 45° PAN LEFT 45° PAN RIGHT .739 18.8 4.75 120.6 16.00 406.4 26.96 684.7 MAX. DISTANCE FROM WALL 29.25 743.0 19.18 487.2 17.72 450.0 MAX. VERT. PATTERN 9.93 252.2 TO CENTER 27.56 700.0 MAX. HORIZ. PATTERN 4 .50 12.7 L/R SHIFT 4.50 114.3 MIN. DISTANCE FROM WALL 2.03 51.6 12° MAX. TILT 18.50 469.9 18.89 479.9 3.45 87.
PAGE 5
Installation Instructions PXR DIMENSIONS...continued PRE-INSTALL SETUP FOR WALL MOUNTING ARMS AND HEAD UNIT HIDDEN FOR CLARITY MECHANICAL MOUNTING PATTERNS: WEIGHT CAPACITY: EXTENSION: 29.50 749.3 PAN: TILT: 4.88 123.8 NOISE LEVEL* MAX SPEED* 5.10 129.5 MINIMUM (H x V) 200 X 100 MAXIMUM (H x V) 700 X 450 Varies dependent on depth of display--150 LB (68.0 KG) MAX UP TO 27" AWAY FROM THE WALL MINIMUM: 4.5" FLUSH MOUNTED, 1.
PAGE 6
PXR Installation Instructions LEGEND 6 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestig
PAGE 7
Installation Instructions PXR TOOLS REQUIRED FOR INSTALLATION M5 3/16" (included) 1/2" (12.7mm) 7/32" (5.5mm) - wood 5/16" (8.0mm) - concrete 9" Hex (included) #2 PARTS A (8) (M4 x 16mm) D (6) M5 x 16mm E (6) M5 x 20mm G (6) M6 x 16mm H (6) M6 x 25mm I (6) M8 x 20mm RA (4) 5/16" RB (4) 5/16" C (6) B (6) M4 x 20mm M4 x 25mm J (6) M8 x 30mm L (8) .750 x .323 x .250 RC (4) 5/16" x 2-1/2" F (6) M5 x 25mm Q (1) [PXR] K (4) M8 x 50mm M (8) .750 x .344 x .
PAGE 8
PXR Installation Instructions SITE PREPARATION IMPORTANT ! : Ensure that PXR location allows required clearance around display as outlined in documentation included with display. Locating and Preparing a Mounting Site The PXR was designed to be installed onto a 16" on center 2" x 4" wood stud or solid concrete wall; or into the PAC-502 in-wall box (not included). 2.
PAGE 9
Installation Instructions PXR PXR DIAGRAM I/O Dip Switches (1-->4) IR Repeater (cable not included) Output at 38kHz 3.5mm mono plug Interface bracket IR Receiver (included) Input 3.
PAGE 10
PXR Installation Instructions INSTALLING TO A WOOD STUD WALL 1. Using a stud finder, locate and mark the two 16" on center 2" x 4" wood studs to which the PXR will be mounted. 2. Determine point for lowest edge of PXR and mark studs. 3. Use a level to join the marked points and mark the lowest edge of PXR. (See Figure 4) 4. Place mounting bracket (X) along marked line on top of level, and mark location of pilot holes. (See Figure 4) 5. Drill two 7/32" x 2-3/4" (5.5mm x 69.
PAGE 11
Installation Instructions PXR 8. Mark the pilot holes through PXR upper bracket. (See Figure 7) 9. Carefully remove the PXR from the mounting bracket. 10. Drill two 7/32" x 2-3/4" (5.5mm x 69.9mm) pilot holes at locations marked in Step 9. 11. Return PXR to mounting bracket and fasten to wall using two 5/16 x 2-1/2" lag screws (RC) and two 5/16" flat washers (RB). (See Figure 7) (RB) x 2 8 10 x2 13 (Z) Figure 9 IMPORTANT ! : Do not power the PXR until it is ready to be tested.
PAGE 12
PXR Installation Instructions WARNING: EXPLOSION AND FIRE HAZARD! CUTTING INSTALLING TO A SOLID CONCRETE WALL OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.
PAGE 13
Installation Instructions 8. 9. 10. 11. 12. 13. PXR Mark the pilot holes through PXR upper bracket. (See Figure 13) Carefully remove the PXR from the mounting bracket. Drill two 5/16" x 3-1/4" (M8 x 82.5mm) pilot holes at locations marked in Step 8. (See Figure 13) Install two anchors (RA) into pilot holes. Tap with hammer until flush with concrete surface. (See Figure 11) and (See Figure 13) Return PXR to mounting bracket.
PAGE 14
PXR Installation Instructions 3 INSTALLING IN AN IN-WALL BOX Strap locations The following procedure assumes that a Chief Listed Model PAC502 In-Wall accessory (not included) has previously been installed following the installation instructions provided with the PAC502. If a PAC502 is not installed or there are any other questions regarding the installation of this accessory, immediately contact a Chief Customer Service representative.
PAGE 15
Installation Instructions PXR 7. Carefully lift up and out slightly on bottom of PXR. (See Figure 21) 8. Route power cord and cables through cable management areas as noted. (See Figure 21) 9. Tighten fasteners to secure top of PXR into PAC502. x2 11 8 Figure 23 12. OPTIONAL: Install PAC502 trim following the instructions included with the PAC502 kit. 7 Figure 21 10.
PAGE 16
PXR Installation Instructions ARM ENGAGEMENT 1. Carefully pull arms out from wall. (See Figure 24) 2. Open cable management covers on bottom of PXR arms. 3. Engage PXR arms by lining up pin with opening and using 9" hex head wrench (Y) in opening on bottom of each arm. (See Figure 25) NOTE: Engage arms by turning fastener to the LEFT. 4. Close cable management covers on bottom of PXR arms.
PAGE 17
Installation Instructions PXR Installing IR Sensor 1. Plug IR receiver (AA) into PXR. (See Figure 3) and (See Figure 26) 2. Route IR receiver to desired location. The IR receiver operates best in open, unobstructed areas. SAVE HOME PAN RIGHT NOTE: The final location of the sensor won’t be made until after installation of the display.
PAGE 18
PXR • Installation Instructions LEARN MODE Phase A 4. Phase A of the LEARN MODE helps the PXR "learn" the amount of resistance in the installation. Phase A will be automatically run by the PXR. The PXR pans to left limit, back to right limit, repeats, tilts up and returns to HOME position before stopping. 1. Press and hold [SAVE] for at least 5 seconds, followed by [STOP]-[RETRACT]-[PAN RIGHT]-[EXTEND]-[PAN LEFT][RETRACT]-[EXTEND] to begin LEARN MODE Phase A.
PAGE 19
Installation Instructions PXR CAUTION: THE INTERFACE BRACKETS ATTACHED TO THE DISPLAY MUST BE THE FURTHEST POINT OF PROTRUSION FROM THE DISPLAY BACK. If the display has any protrusions from the back it may be necessary to add spacers during attachment to the interface brackets, so that interface brackets are furthest protrusion from back of PXR.
PAGE 20
PXR 2. Installation Instructions Lock display with attached interface brackets to PXR using two bracket locks (W) and four 1/4-20 x 1/2" hex head cap screws (U). (See Figure 31) and (See Figure 33) IMPORTANT ! : If possible, place display’s power and signal cables in separate PXR arms. 1. (V) Open cable management covers on top of both PXR arms. (See Figure 34) and (See Figure 35) 1 (W) Figure 35 (U) (view from back of PXR) Figure 33 Cable Management 2.
PAGE 21
Installation Instructions PXR 5. Open cable management covers on bottom of both PXR arms and lay cables within arms. (See Figure 34) and (See Figure 37) 6. Close cable management covers, being careful to not pinch cables under covers. (See Figure 37) 8. If necessary, use cable management flap on PXR base to route cables from left arm to PXR right side. (See Figure 34) and (See Figure 39) 5 8 6 Figure 37 7. Figure 39 Continue to route cables through vertical cable management slots.
PAGE 22
PXR Installation Instructions CAUTION: ENSURE INTERFACE BRACKETS ARE LOCKED TO THE PXR RAILS BEFORE BEGINNING LEARNING MODE! The display must be centered on the PXR so that the learning mode can be completed successfully. Wall 2" MINIMUM NOTE: The LEARN MODE is used to calibrate the PXR for use with the specific display which has been attached to it. • • If the process is cancelled at any point during Phase A or B it will need to begin again from Phase A.
PAGE 23
Installation Instructions 3. PXR Add plastic covers (P) to PXR, fastening with two 8-32 x 1/4" Phillips flat head screws (S). (See Figure 41) ADVANCED SETTINGS NOTE: Normal operation is a green light slowly fading on/off (seen through main control board housing). (P) NOTE: If red light is on without blinking, the IR receiver cable may not be completely plugged in. IR Repeat Conditions NOTE: The PXR is equipped with a built-in IR repeater that works with most IR transmitters (38kHz).
PAGE 24
PXR Installation Instructions PROGRAMMING VIA RS485 Setting PXR Address NOTE: If multiple PXR’s or Chief automated products will be controlled in the same area AND need to have UNIQUE command codes, the PXR or other Chief automated product will need to have its address changed. ON 1. Determine what address is not used by another Chief automated product. 2. Using the DIP switches on the I/O interface (See Figure 44), set the PXR to one of the unused addresses.
PAGE 25
Installation Instructions PXR Common Commands In order to move the PXR incrementally, the remote control must be used. The only way to move the PXR with RS-485 is by commanding it to go to the Home position or a predefined preset. See Saving a Preset section for more information. The PXR ships with the default address of 00 (all I/O DIP switches set to "Off"). The PXR has a product ID code value of 06.
PAGE 26
PXR Installation Instructions Get System Status (0x2F) Command Message SOM Product ID Address Command Check Code EOM > 06 XX 2F XX Status Response with Position Data SOM System Status Check Code EOM < XXXX XX Example of how to get the blink code status of the PXR (assumes product address is 00) Send command >06002F93 response = <805022 This would indicate the unit has a status of 8050 (check digits 22), blinking 5 times and that the unit has not successfully been through LE
PAGE 27
Installation Instructions PXR Chief Part Number: 7000-002052 Carrier Frequency: 38KHz Protocol: NEC - Full Repeat System Code(s): 6E (Default) - Multiple codes selected via key-press (See Figure 46) Repeat Code: N/A Key Number Key Name 1 Hex Code HOME 02 2 SAVE 1A 3 RETRACT 07 4 SWIVEL LEFT 09 5 STOP 0A 6 SWIVEL RIGHT 0B 7 EXTEND 0D 8 TILT UP 08 9 TILT DOWN 0E 10 N/A N/A 11 N/A N/A 12 PRESET 1 12 13 PRESET 2 13 14 PRESET 3 14 15 PRESET 4 15 + + _
PAGE 28
PXR Installation Instructions RS-485 Terminal Block Wiring 6 5 4 3 2 1 Figure 48 Terminal Block Manufacturer: Molex (See Figure 48) • Terminal Block Manufacturer P/N: 39500-0006 • Terminal Block Pin Outs: 1. 2. 3. 4. 5. 6. • Blank TDA (-) TDB (+) Ground Blank Blank Wire terminal block using 16-30AWG wire. IR Receiver Pinout O 3.
PAGE 29
Installation Instructions PXR 29
PAGE 30
PXR 30 Installation Instructions
PAGE 31
Installation Instructions PXR 31
PAGE 32
PXR Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002079 Rev00 2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 04/11 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No.