INSTALLATION INSTRUCTIONS Large Flat Panel Dual Arm Wall Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description PNR Series
PNR Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions PNR Series DIMENSIONS NOTE: PSBU INTERFACE BRACKET NOT SHOWN. THE PSBU INTERFACE BRACKET WILL ADD 1” IN DEPTH AND MAY AFFECT THE LOCATION OF THE DISPLAY ON THE MOUNT. Mount ing Patter n 483 19.00 46 1.81 25 1.00 178 7.00 38 1.50 25 1.00 500 19.69 538 21.19 10 .40 406 16.00 4 .
PNR Series Installation Instructions DIMENSIONS -- cont’d Unit Depth Extended Tilt Adjustment * Retracted Tilted Up Tilted Down 5° 17° 83 3.25 635 25.00 687 27.06 *The range of adjustment will v ary with different size s creens 2° 66 2.61 Highest Height Setting 39 1.53 Lowest Height Setting Roll Adjustment 90.00° 18.21 161.09° MAX 76.17° MAX 22.65 MAX 76.17° MAX 10.
Installation Instructions PNR Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Beves
PNR Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 7/32" (5.5mm) 9/16" PARTS B (2) [Cover] A (1) [PNR assembly] C (2) [End cap] E (1) [Adjustment wrench] H (4) 5/16 x 2-1/2" F (1) [Adjustment insert] D (2) [End cap] G (4) .850x.385x.
Installation Instructions PNR Series 5. Installing Mount to Wall Drill four 7/32" pilot holes where the mounting holes were marked. (See Figure 2) WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the structure to which the mount is being installed is capable of supporting five times the combined weight of the mount and all attachments.
PNR Series Installation Instructions 6. Install two 5/16” x 2-1/2” lag bolts (H) and two .850x.385x.135” washers (G), through mounting holes in upper wall channel and into pilot holes. DO NOT tighten at this time. (See Figure 3) 7. Place mount against wall aligning mounting holes in upper wall channel with lag bolts, and hang mount on lag bolts making sure washers are located in front of mount. 8. Adjust mount lateral position left until lag bolts are seated in mounting slots in upper wall channel.
Installation Instructions PNR Series Mounting the Display WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Displays can weigh in excess of 40 lbs (18.1kg). ALWAYS use two people and proper lifting techniques when installing display. 1. Install PSBU interface bracket (K - included with PNRU only) to display using hardware and installation instructions included with PSBU bracket. 2.
PNR Series Installation Instructions Tension Adjustments Cable Management Vertical Tilt Tension Adjustment WARNING: IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Make sure cables do not run through pinch points. 1. Thread cable ties (J) under cable clamps in mount arms. (See Figure 1) 1. With display mounted, check for desired vertical tilt tension. 2. Adjust the Centris Select knob until desired vertical tilt tension is obtained. (See Figure 9) 3.
Installation Instructions PNR Series Swing Arm Adjustments Swivel Tension Adjustment CAUTION: DO NOT OVER TIGHTEN SWIVEL The dual swing arms are shipped installed in the center of the top and bottom mounting brackets, which is the standard mounting configuration. ADJUSTMENT NUT. Over tightening swivel adjustment nut will cause excessive wear and may distort adjustment components. The top and bottom mounting brackets have slotted holes, allowing for lateral adjustment of the dual swing arms. 1.
PNR Series Installation Instructions Reconfiguring the Swing Arms to Left or Right of Center 1. 3. Remove the display from the mount. WARNING: The next step will release the arm assembly from the mount. The arms and plate may fall if you are not careful. 2. Remove four bolts (two on the top and two on the bottom) securing the swing arm assembly to the top and bottom mounting brackets. (See Figure 13) Move the swing arm assembly left or right within slots to desired location.
Installation Instructions PNR Series Swing Arm Tension Adjustment Swing arm tension is pre-set at the factory and is adjusted to accommodate displays with weights near the top of the mount’s capacity. If smaller displays are used it may be difficult to reposition the display after mounting. Increase tension NOTE: The display must be mounted prior to adjusting swing arm tension. To adjust swing arm tension to compensate for smaller display: 1.
PNR Series Installation Instructions Removing Display from Mount 3. Carefully lift display from mount 1. 4. Lift up on pin and place flag back against faceplate to return it to "Closed" position. (See Figure 19) Remove bolt or padlock from faceplate (if used). NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes. 2. Pull back on flag on upper mounting hole and press pin down into "Open" position.
Installation Instructions PNR Series 15
PNR Series Installation Instructions USA/International Europe Chief, a products division of Milestone AV Technologies 8800-002618 Rev00 2014 Milestone AV Technologies www.chiefmfg.com 07/14 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
