INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Large Flat Panel In-Wall Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description PIWRF SERIES
PIWRF SERIES DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
PIWRF SERIES Installation Instructions DIMENSIONS LEGEND Tighten Fastener Hex-Head Wrench Apretar elemento de fijación Llave de cabeza hexagonal Befestigungsteil festziehen Sechskantschlüssel Apertar fixador Chave de cabeça sextavada Serrare il fissaggio Chiave esagonale Bevestiging vastdraaien Zeskantsleutel Serrez les fixations Clé à tête hexagonale Loosen Fastener Open-Ended Wrench Aflojar elemento de fijación Llave de boca Befestigungsteil lösen Gabelschlüssel Desapertar fixador
Installation Instructions PIWRF SERIES TOOLS REQUIRED FOR INSTALLATION AND PARTS 1/2" 1/8" 7/16" 9/16" 1" NOTE: Listed PSBU interface bracket provided with Listed Model PIWRFUB, but not shown.
Installation Instructions PIWRF SERIES Installation WARNING: IMPROPER INSTALLATION CAN RESULT IN DEATH OR SERIOUS PERSONAL INJURY! This accessory should be installed by qualified personnel only. Cutout Area WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! DO NOT deviate from installation instructions provided. DO NOT substitute hardware.
PIWRF SERIES Installation Instructions WARNING: ELECTRICAL SHOCK HAZARD! CUTTING WARNING: IMPROPER INSTALLATION CAN LEAD TO OR DRILLING INTO ELECTRICAL WIRES OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surfaces is free of electrical wires and cables before cutting, drilling, or installing fasteners.
Installation Instructions PIWRF SERIES Cover and Trim Installation Cover Installation (F2) x 4 (F1) x 4 To install covers: 1. (A) x 1 2. 3. 9 Install upper and lower wall channel covers (E) by tipping cover top down and positioning as shown in end view of figure below. (See Figure 8) Tap firmly across bottom of channels to lock in place as shown in figure below. (See Figure 8) Install four R.H. and L.H.
PIWRF SERIES Installation Instructions 1. Trim Installation To install optional trim; 1. 2. 2. Orient two trim pieces (G) as shown in figure below. (See Figure 9) Slide slat in trim edge over lip in mount enclosure and press trim (G) onto enclosure. (See Figure 9) 3. 4. (G) x 2 Install Listed interface bracket following the installation instructions provided with the interface bracket. Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall.
Installation Instructions PIWRF SERIES ADJUSTMENTS CABLE MANAGEMENT Pitch Tension Adjustment WARNING: IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Make sure cables do not run through pinch points. 1. Locate and install cable tie clips (J) where desired for proper cable routing. (See Figure 12) To adjust display pitch tension: 1. 2. 3. With display installed, tighten or loosen two screws, one on each side. (See Figure 14) Check for desired tension.
PIWRF SERIES Installation Instructions Roll Adjustment 3. The mount allows for the horizontal alignment (Roll) of the display to be adjusted up to 2° right or left to level the display after installing. NOTE: If changing from a smaller display to a larger display it Repeat Steps 1 and 2 until desired tension is obtained. may be necessary to increase tension. To adjust Roll: 1. Loosen the roll tension adjustment nut located on the back side of the faceplate assembly. (See Figure 15) 2. Level display.
Installation Instructions PIWRF SERIES Display Height Adjustment The mount is designed to accommodate up to 1" of display height adjustment. 1 To adjust display height: 1. 2. 3. With display installed, loosen adjustment locking screw using hex wrench. (See Figure 17) Adjust display height by turning adjustment nut in desired direction. (See Figure 17) Tighten adjustment locking screw when display is at desired height.
PIWRF SERIES Installation Instructions USA/International Chief Manufacturing, a products division of Milestone AV Technologies 8805-000248 RevB 2009 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 12/09 Europe Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No.
