INSTALLATION INSTRUCTIONS Projector Guard Security Cage PG1A, PG2A
PG1A, PG2A Installation Instructions DISCLAIMER CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions PG1A, PG2A PG1A PG2A [101.600] 4.00 [415.925] 16.38 OD 1.5” NPSM COUPLER WILL ALLOW FOR 2.50” OF FRONT TO BACK ADJUSTABLE SHIFT [89.687] 3.53 [50.800] 2.00 [404.503] 15.93 ID [406.400] ID 16.00 [258.589] OD 10.18 [199.996] 7.87 FROM BOTTOM OF RPA TO SURFACE OF RIVETS [410.195] OD 16.15 NOTES: 1. RPA AND SLB BRACKET SOLD SEPARATELY. 2. HEIGHT DIMENSION DOES NOT INCLUDE SLB/SLM INTERFACE. YOU MUST ALLOW FOR .25” TO .
PG1A, PG2A Installation Instructions LEGEND 4 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro B
Installation Instructions PG1A, PG2A TOOLS REQUIRED FOR INSTALLATION 1/2" (12.7mm) PARTS B (1) (PG2A only) A (1) (PG1A only) G (4) 10-24 X 3/8" [PG1A-black PG2A-stainless steel] E (1) D (2) C (1) H (4) 1/4-20 X 3/4" I (4) 1/4-20 X 1-1/2" J (2) 5/16" K (4) 1/4" L (2) 5/16" M (2) .68x.39x.625 F (1) N (4) .5x.26x.
PG1A, PG2A Installation Instructions Assembly And Installation 2. NOTE: The PG1A and PG2A should not be used in a flush Attach two interface brackets (D) to RPM using four 1/4-20 x 1-1/2" buttonhead cap screws (I) and four nylon spacers (N). (See Figure 3) ceiling mount. (D) x 2 NOTE: The projector must be removed from the mount before installing this accessory. RPM Removing Projector from Ceiling Mount 1. Power off the projector and disconnect the power cord. 2.
Installation Instructions PG1A, PG2A (PG2A shown) Thumbnuts Threaded Studs Removable filler bar Leave two screws in to make a hinged door SLB Filler Bar Security Screws RPA/RPM Mount Figure 6 Figure 5 2. Place projector inside the projector guard (See Figure 5) NOTE: The front fillers serve two different purposes, and the number of fillers varies between the PG-1A and PG-2A. The front filler(s) can be installed to accommodate the various projector lens positions. 3.
PG1A, PG2A Installation Instructions 2. Install the clamp and fasteners as follows: a. For 1-1/2" NPT install the clamp at the desired height and secure using the U-bolt, two flat washers, two lock washers, and two 5/16-18 hex nuts (provided with U-bolt). (See Figure 10) (H) x 4 (P) x 4 (K) x 4 (F) NPT Pipe (C) Projector Guard Slots x4 6 Provided with U-bolt (G) x 4 (L) x 2 Figure 8 5.
Installation Instructions PG1A, PG2A 9
PG1A, PG2A 10 Installation Instructions
Installation Instructions PG1A, PG2A 11
PG1A, PG2A Installation Instructions USA/International Europe Asia Pacific 8803-000059 RevD 2007 Chief Manufacturing www.chiefmfg.com 10/07 A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA.
