INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Large Flat Panel Dual Arm Wall Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description PDR Series
PDR Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions PDR Series DIMENSIONS -- cont’d Tilt Adjustment * Unit Depth Extended Retracted [86] 3.40 940 37.00 1003 39.50 *The range of adjustment will vary with different weight and depth screens Highest Height Setting 71 2.81 43 1.68 Lowest Height Setting 90° 84° 825 32.47 79° MAX 284 11.19 689 27.12 23° 450 17.
PDR Series Installation Instructions LEGEND 4 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro B
Installation Instructions PDR Series TOOLS REQUIRED FOR INSTALLATION #2 7/32" (5.5mm) 9/16" PARTS NOTE: Listed PSBU interface bracket provided with Listed Model PDRUS/B, but not shown.
PDR Series Installation Instructions MOUNT INSTALLATION 9. Installing Mount to Wall 10. Install two 5/16" x 3-1/2" lag bolts (H) through mounting holes in lower wall channel and into pilot holes.
Installation Instructions PDR Series WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Make sure mounting buttons on display are properly seated in mounting holes in faceplate. 1. Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall. 2. While supporting both sides of display, align four mounting buttons on display or interface bracket with four mounting holes in faceplate. (See Figure 5) 3.
PDR Series Installation Instructions (J) cable clamps 1 x4 2 Figure 7 Cable Management Centris Select Adjustment Knob WARNING: IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Make sure cables do not run through pinch points. 1. Loosen front and rear cable clamps on top arm. (See Figure 7) 2. Thread cable ties (J) under cable clamps and secure clamps to top arm. (See Figure 7) 3.
Installation Instructions PDR Series Lateral Tilt Tension Adjustment CAUTION: DO NOT OVERTIGHTEN LATERAL TILT ADJUSTMENT NUT. Overtightening lateral tilt adjustment will cause excessive wear and may distort adjustment components. 1. Using a 9/16” wrench (not provided), slightly tighten or loosen lateral tilt tension adjustment nut. (See Figure 10) 2. Attach the display and check for desired tilt tension. 3. Repeat Steps 1 and 2 until desired tilt tension is obtained.
PDR Series Installation Instructions WARNING: The next step will release the arm assembly from the mount. The arms and plate may fall if you are not careful. 3. Move the swing arm assembly to desired location. • Left of Center (See Figure 12). • Right of Center (See Figure 13). 1. Locate the adjustment insert (F) and wrench (E) provided with the mount. 2. Place adjustment insert into socket head cap screw located at swing arm pivot point.
Installation Instructions PDR Series Removing Display from Mount 1. Remove bolt or padlock from faceplate (if used). NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes. 2. 1 Remove bolt or padlock if used 2 Pull back on flag on upper mounting hole and press pin down into "Open" position.
PDR Series Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002473 Rev00 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 10/13 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
