User Manual

ManualsBrandsCHIEF ManualsHardwarePAC200

INSTALLATION INSTRUCTIONS

CHIEF MANUFACTURING INC.

1-800-582-6480 952-894-6280 FAX 952-894-6918

8401 EAGLE CREEK PARKWAY, STE 700

SAVAGE, MINNESOTA 55378 USA

8809-000035 RevA

2007 Chief Manufacturing

www.chiefmfg.com

12/07

BEFORE YOU BEGIN

PPC TO PPD ADAPTER

Model: PAC-200

Specifications:

• Design ed for installation on Chief PPC Cart.

NOTE: The PAC-200 re -uses certain components and

hardwa re from the original single display PPC

configuration.

• Infinite tilt adjustment between 0° and 7.5°.

PAC-200

(Shown installed on PPC cart, purchased separately)

WARNING: It is the installer’s responsibility to make sure all components are properly assembled and installed

using the instructions provided. Failure to read, thoroughly understand, an d follow all instructions can result in

serious personal injur y, damage to equi pm ent, or void ing of factory warranty.

• If you have any questions about this these instructions or your specific installation, contact Chief Manufacturing

at 1-800-582-6480 or 95 2-894-6280.

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS PPC TO PPD ADAPTER Model: PAC-200 Specifications: • Designed for installation on Chief PPC Cart. NOTE: The PAC-200 re-uses certain components and hardware from the original single display PPC configuration. • Infinite tilt adjustment between 0° and 7.5°. PAC-200 (Shown installed on PPC cart, purchased separately) BEFORE YOU BEGIN WARNING: It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
PAGE 2
Model: PAC-200 Installation Instructions IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
PAGE 3
Installation Instructions Model: PAC-200 TOOLS REQUIRED FOR INSTALLATION • • 5/32" Hex Key (included) 3/16" Hex Key (included) 10 NOTE: Other tools may be required depending on your method of installation. PARTS After unpacking carton, inspect and verify contents (See Figure 1). If any listed parts are missing or damaged, contact Chief Customer Service at 1-800-582-6480.
PAGE 4
Model: PAC-200 Installation Instructions INSTALLATION REMOVE EXISTING PPC COMPONENTS WARNING: Display is very heavy! Ensure display can be safely lifted and maneuvered as required for removal. Failure to take adequate precaution can result in serious personal injury or damage to equipment! 3. Using hex key (60), remove four 1/4"-20 x 5/8" button head cap screws attaching single mount head to leg brackets (See Figure 3). Retain screws for later use.
PAGE 5
Installation Instructions Model: PAC-200 INSTALL PAC-200 COMPONENTS 1. Determine desired height for head (20) keeping in mind display size and viewing requirements. 2. Using hex key (60), install six retained 1/4"-20 x 5/8" button head cap screws through selected fastener holes in leg brackets, through head (20), into spreaders (40) (See Figure 4). Tighten securely. Ensure the following: • • 4. If not previously installed, install interface (not included) to each display.
PAGE 6
Model: PAC-200 Installation Instructions ADJUSTMENT Mounting Hole Set 12 34 12 Faceplate/ Side Bracket Assembly 34 TILT 1. Using hex key (60), slightly loosen six screws used to attach head (20) and spreaders (40) to leg brackets (See Figure 8). Do NOT remove screws. (left side shown; right side similar) 10 (4 places) NOTE: Right faceplate/side bracket assembly shown installed in Set 1; left side set opposite. 20 Figure 7: Install Faceplate/Side Bracket Assembly 8.