INSTALLATION INSTRUCTIONS Medium Flat Panel In-Wall Swing Arm Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description MWRIW Series
MWRIW Series DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions MWRIW Series LEGEND Tighten Fastener Hex-Head Wrench Apretar elemento de fijación Llave de cabeza hexagonal Befestigungsteil festziehen Sechskantschlüssel Apertar fixador Chave de cabeça sextavada Serrare il fissaggio Chiave esagonale Bevestiging vastdraaien Zeskantsleutel Serrez les fixations Clé à tête hexagonale Loosen Fastener Phillips Screwdriver Aflojar elemento de fijación Destornillador Phillips Befestigungsteil lösen Kreuzschlitzschraubendreher Desape
MWRIW Series Installation Instructions DIMENSIONS DIMENSIONS: [MILLIMETERS] INCHES DIMENSIONS: [MILLIMETERS] INCHES 4
Installation Instructions MWRIW Series TOOLS REQUIRED FOR INSTALLATION AND PARTS 3/16" (provided) NOTE: Listed MSBU interface bracket provided with Listed Model MWRIWUB, but not shown.
MWRIW Series Installation Instructions Installation The following procedure assumes that a Chief Listed Model PAC501 In-Wall accessory has previously been installed following the installation instructions provided with the PAC501. If a PAC501 is not installed or there are any other questions regarding the installation of this accessory, immediately contact a Chief Customer Service representative.
Installation Instructions MWRIW Series Display Installation WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! DO NOT install display in a manner other than that specified by the manufacturer. Certain displays may require the use of an interface bracket for proper installation of the display.
MWRIW Series Installation Instructions Cable Management 1. 2. Attach all cables to display. If necessary, use cable tie mounts (G) and cable ties (M) to secure cables within PAC501. WARNING: IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Make sure cables do not run through pinch points. 3. 4. 5. 6. 7. Loosen front and rear cable clamps on top arm. (See Figure 6) Thread cable ties (E) under cable clamps and secure clamps to top arm.
Installation Instructions MWRIW Series ADJUSTMENTS 2 Pitch Tension Adjustment To adjust display pitch tension: 1. 2. 3. With display installed, tighten or loosen two screws, one on each side, using the 5/32” hex wrench. (See Figure 7) Check for desired tension. Repeat Steps 1 and 2 until desired tension is obtained.
MWRIW Series Installation Instructions Swing Arm Tension Adjustment Swing arm tension is pre-set at the factory and is adjusted to accommodate displays with weights near the top of the mounts capacity. 4 DECREASE If smaller displays are used it may be difficult to reposition the display after mounting. Swing arm tension can be adjusted to compensate for smaller display by: The display must be mounted prior to adjusting swing arm tension. 1. 2. Locate the adjustment bar (K) and adjustment wrench (L).
Installation Instructions MWRIW Series 11
MWRIW Series Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8805-000244 Rev03 2010 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 02/10 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No.
