INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Medium Flat Panel Wall Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description MWH
MWH Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions MWH TOOLS REQUIRED FOR INSTALLATION AND PARTS 7/32" (Ø 6mm) I/M A (1) x1 B (2) F (4) C (1) E (4) D (1) G (4) 5/16 x 2-1/2" H (4) 5/16" 3
MWH Installation Instructions DIMENSIONS NOTE: CUSTOM INTERFACE BRACKET NOT SHOWN. THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR DISPLAY WILL ADD BETWEEN 1/2" AND 2" IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY ON THE MOUNT. Mounting Pattern HEIGHT ADJUSTMENT 100 LBS B ,-15 / 2.5 / 0 114 4.50 87 3.43 19 .75 C SEE MSB-XXXX DRAWING ALSO. PRODUCT FEATURES WEIGHT CAPACITY 10 .39 58 2.30 457 18.00 397 15.65 64 2.
Installation Instructions MWH Mount Installation and into pilot hole. (See Figure 3) Tighten all hardware. DO NOT overtighten! 9. WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the structure to which the MWH is being installed is capable of supporting five times the combined weight of the mount and all attachments. 7/32" (Ø 6mm) x2 1.
MWH Installation Instructions Cover Installation To install channel covers: 1. 2. 3. Install upper and lower wall channel covers (B) by tipping cover top down and positioning as shown in end view of figure below. (See Figure 4) Tap firmly across bottom of channels to lock in place as shown in figure below. (See Figure 4) Install four R.H. and L.H.
Installation Instructions MWH Display Installation If the mounting pattern of the display being installed is a VESA standard 200 x 200 pattern the mounting buttons can be installed directly to the back of the display. If the display has any other mounting pattern an interface bracket must be obtained before proceeding. Consult a Chief Customer Service representative if an interface bracket is required by calling 1-800-582-6480 or visit www.chiefmfg.com. Remove pin 4 and nuts and move to lower holes.
MWH Installation Instructions (A) x 4 (E) x 4 x4 From Display Figure 7 ADJUSTMENTS Pitch Tension Adjustment 1 X2 To adjust display pitch tension: 1. 2. 3. With display installed, tighten or loosen two screws, one on each side, using the 5/32” hex wrench. (See Figure 8) Check for desired tension. Repeat Steps 1 and 2 until desired tension is obtained.
Installation Instructions MWH Roll Adjustment The MWH allows for the horizontal alignment (Roll)of the display to be adjusted up to 2 deg. right or left to level the display after installing. (D) x 1 (C) x 1 To adjust Roll: 1. 2. 3. Loosen the roll tensions adjustment nut located on the back side of the faceplate assembly. (See Figure 9) Level display. Tighten roll tension adjustment nut. (See Figure 9) 2 Socket Head Capscrew 1 Figure 10 4.
MWH 10 Installation Instructions
Installation Instructions MWH 11
MWH Installation Instructions USA/International Chief Manufacturing, a division of Milestone AV Technologies Europe Asia Pacific 8831-000009 RevI ©2008 Milestone AV Technologies www.chiefmfg.com 07/08 A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA.
