INSTALLATION INSTRUCTIONS MSA1U LSA1U MTA1U LTA1U FUSION MEDIUM AND LARGE FLAT PANEL MOUNTS MSA1U/MTA1U/LSA1U/LTA1U
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U DIMENSIONS MSA1U 6.00 152.4 RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET 1. 2. 3. MAXIMUM MOUNTING PATTERN IS 22.7" (576 mm) WITHOUT REVERSING UPRIGHTS MAXIMUM MOUNTING PATTERN IS 25.3" (642 mm) WITH REVERSING UPRIGHTS FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK ENGAGEMENT IS .75" (19 mm) DIMENSIONS: INCHES [MILLIMETERS] MTA1U 6.00 152.4 RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET 1. 2. 3. MAXIMUM MOUNTING PATTERN IS 22.
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions DIMENSIONS--continued LSA1U 1.45 36.9 6.00 152.4 15.00 381.0 DIMENSIONS: INCHES [MILLIMETERS] LTA1U 16.00 406.3 MINIMUM UPRIGHT SPACING 6.00 152.4 RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET 1. 2. 3. 4 MAXIMUM MOUNTING PATTERN IS 31.25" (794 mm) WITHOUT REVERSING UPRIGHTS MAXIMUM MOUNTING PATTERN IS 34.6" (879 mm) WITH REVERSING UPRIGHTS FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK ENGAGEMENT IS .
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare u
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" x 10" (included) 7/32" (5.5mm) Wood Stud 3/8" (9.
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U INSTALLATION The MSA1U/MTA1U/LSA1U/LTA1U mounts are designed to be mounted to a bare 8" concrete, 8"x8"x16" concrete block; or 2" x 4" wood studs (16" on center for MSA1U/MTA1U, and 16" or 24" on center for LSA1U/LTA1U) wall covered by drywall with 5/8" maximum thickness. The MTA1U and LTA1U have brackets which allow the TV to be tilted. The MSA1U and LSA1U have static brackets which keep the TV in an upright position. Locate Mounting Site 5.
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions Installing to a Concrete Wall 1. Determine the center of the TV screen, and where it should be located on the wall. 2. Line up the diamond shapes on mount (Z) with center of screen marking to determine vertical center. (See Figure 1) 3. Measure up 7" (177.8mm) from the center point to mark location of the upper mounting slots. 4. Using a level, mark the wall through both upper mounting slots. (See Figure 3) 6 10 13.
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U NOTE: The nesting spacers (MA) may be used separately, or put two together in different configurations to create different size spacers. (See Figure 5) (Stacked) (Nested) (Single) .563" .391" .750" Figure 5 3. If necessary, the tilt interface bracket knobs may be switched to allow the interface brackets (X and Y) to be reversed. (See Figure 7) a. Remove display from mount. b. Remove interface brackets from display. c.
MSA1U/MTA1U/LSA1U/LTA1U Attaching Screen to Wall Mount NOTE: NEVER place both interface brackets (V and W or X and Y) to one side of the wall mount center line! (See Figure 8) NOTE: Do NOT allow both interface brackets (V and W or X and Y) to be located on same side of wall bracket.
Installation Instructions 1. MSA1U/MTA1U/LSA1U/LTA1U Hang screen onto the top rail of the mount (CC). (See Figure 9) • MSA1U / LSA1U: Hang top hook of interface brackets (V and W) onto the top rail of the mount (Z). (See Figure 9) • MTA1U / LTA1U: Move latch on top of interface bracket to OPEN position and hang top hook of interface brackets (X and Y) onto the top rail of the mount (Z). (See Figure 9) NOTE: The screen initially installs into the "service mode" to allow easy cable access. 2.
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions Adjustments Horizontal Adjustment 1. 3 (U) The mount wall brackets may be adjusted side to side at the point of attachment. (See Figure 10) 1 1" (25.4mm) horizontal adjustment possible Latch in CLOSED position (T) 2 Figure 10 2. Interface bracket knob The screen may also be adjusted along rails side to side.
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U Locking Screen Interface Brackets (Optional) Locking Mount (Optional) 1. 1. Lock screen interface brackets onto mount rails using one 3/8-16 x 3/4" set screw (S) on each interface bracket. (See Figure 12) Add padlock (not included) to interface bracket to complete security. (See Figure 13) NOTE: The padlock maximum shackle diameter is 5/16" (7.9 mm).
MSA1U/MTA1U/LSA1U/LTA1U 14 Installation Instructions
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U 15
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions USA/International Europe Chief, a products division of Milestone AV Technologies 8800-002649 Rev02 2015 Milestone AV Technologies www.chiefmfg.com 01/15 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
