INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Medium Flat Panel In-Wall Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description MIWRF SERIES
MIWRF SERIES DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
MIWRF SERIES Installation Instructions DIMENSIONS LEGEND Tighten Fastener Hex-Head Wrench Apretar elemento de fijación Llave de cabeza hexagonal Befestigungsteil festziehen Sechskantschlüssel Apertar fixador Chave de cabeça sextavada Serrare il fissaggio Chiave esagonale Bevestiging vastdraaien Zeskantsleutel Serrez les fixations Clé à tête hexagonale Loosen Fastener Open-Ended Wrench Aflojar elemento de fijación Llave de boca Befestigungsteil lösen Gabelschlüssel Desapertar fixador
Installation Instructions MIWRF SERIES TOOLS REQUIRED FOR INSTALLATION AND PARTS 1/2" 1/8" 7/16" 9/16" 1" NOTE: Listed MSBU interface bracket provided with Listed Model MIWRFUB, but not shown. Listed MSBV interface bracket provided with Listed Model MIWRFVB, but not shown.
MIWRF SERIES Installation Instructions INSTALLATION WARNING: IMPROPER INSTALLATION CAN RESULT IN DEATH OR SERIOUS PERSONAL INJURY! This accessory should be installed by qualified personnel only. Cutout Area WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! DO NOT deviate from installation instructions provided. DO NOT substitute hardware.
MIWRF SERIES Installation Instructions WARNING: ELECTRICAL SHOCK HAZARD! CUTTING WARNING: IMPROPER INSTALLATION CAN LEAD TO OR DRILLING INTO ELECTRICAL WIRES OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surfaces is free of electrical wires and cables before cutting, drilling, or installing fasteners.
MIWRF SERIES Installation Instructions Cover and Trim Installation Cover Installation To install covers: (F1) x 4 (F2) x 4 1. 2. 3. 9 (A) x 1 Install upper and lower wall channel covers (E) by tipping cover top down and positioning as shown in end view of figure below. (See Figure 8) Tap firmly across bottom of channels to lock in place as shown in figure below. (See Figure 8) Install four R.H. and L.H.
MIWRF SERIES Installation Instructions 1. Trim Installation To install optional trim; 1. 2. 2. Orient two trim pieces (G). (See Figure 9) Slide slat in trim edge over lip in mount enclosure and press trim (G) onto enclosure. (See Figure 9) (G) x 2 3. 4. Install Listed interface bracket following the installation instructions provided with the interface bracket. Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall.
Installation Instructions MIWRF SERIES ADJUSTMENTS CABLE MANAGEMENT Pitch Tension Adjustment WARNING: IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Make sure cables do not run through pinch points. 1. Locate and install cable tie clips (J) where desired for proper cable routing. (See Figure 12) To adjust display pitch tension: 1. 2. 3. With display installed, tighten or loosen two screws, one on each side. (See Figure 14) Check for desired tension.
MIWRF SERIES Installation Instructions 2 1 1 (on back side in this view) 3 2 Figure 16 Display Height Adjustment The mount is designed to accommodate up to 1" of display height adjustment. To adjust display height: 1. Figure 15 Extend/Retract Tension Adjustment Arm Extend and Retract tension is pre-set at the factory and is adjusted to accommodate displays with weights near the top of the mounts capacity. 2. 3. With display installed, loosen adjustment locking screw using hex wrench.
Installation Instructions MIWRF SERIES YAW Tension Adjustment The mount is designed to accommodate up to 37.5° of travel to left and right of center. To adjust YAW tension: 1. With display installed, loosen adjustment screw using hex wrench. (See Figure 18) 2. Check for desired tension. 3. Repeat Steps 1 and 2 until desired tension is obtained. NOTE: If changing from a smaller display to a larger display it may be necessary to increase tension.
MIWRF SERIES Installation Instructions USA/International Chief Manufacturing, a products division of Milestone AV Technologies Europe Asia Pacific 8805-000249 RevB 2009 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 11/09 A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No.
