INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation K4W210 K4W310 K4W120 Kontour™ Articulating Array Arm Wall Series Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description K4W120-210-310
K4W120-210-310 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions K4W120-210-310 DIMENSIONS K4W210 37.14 943.3 K4W310 24.13 612.
K4W120-210-310 Installation Instructions DIMENSIONS (CONTINUED) K4W120 19.90 505.5 VESA 100 X 100 & 75 X 75 COMPATIBLE 3.70 94.0 11.59 294.3 20.24 514.1 16.00 MAX [406.4] 12.00 MIN [304.8] 2.58 65.5 5.43 138.0 2.63 66.7 4.69 119.1 4 1.60 40.5 9.01 228.7 3X 0.27 6.
Installation Instructions K4W120-210-310 LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro B
K4W120-210-310 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1/8” (wood stud) 5/16” (concrete) (concrete only) #2 5/16” (included) 3/16” (included) 1/8” (included) PARTS Hardware bag (parts numbered on bag as shown) A1 (2) 3/8-16 x 2 3/4” A2 (2) 3/8” D1 (2) #10-32 x 1/2” *8 for K4W210 or K4W120 and 12 for K4W310 E1 (4) [tie mount] E2 (4) #10-24 x 3/8” J (2) (K4W310 only) [channel attachment] M (8/12)* M4x30mm N (8/12)* M4x20mm B (3) 1/4 x 2 1/2” D2 (2) #10-32 x 3/8” F2 (1) 3/16”
Installation Instructions K4W120-210-310 Assembly And Installation 8. Drill two 1/8” holes at locations marked in Step 6. (See Figure 2) Install to Wall 9. Hang arm assembly (Z) back onto wall. Install Arm Assembly to Wall - Wood Studs 10. Install two 1/4 x 2 1/2” lag bolts (B) into holes drilled in Step 8 to secure mount to wall. (See Figure 2) WARNING: Failure to provide adequate structural strength 11. Tighten all three lag bolts (B) to fully secure mount to wall.
K4W120-210-310 Installation Instructions Install Arm Assembly to Wall - Hollow Concrete Block or Poured Concrete WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.
Installation Instructions K4W120-210-310 K4W210/310 Installation to Arm 1. (K4W210 shown) Use two 3/8-16 x 2 3/4” socket head carriage screws (A1) and two 3/8” lock nuts (A2) to secure left array arm (X) and right array arm (Y) to array center (AA or BB). (See Figure 5) (AA) (K4W210 shown) (A1) x 2 1 (Z) (D2) x 2 3 Figure 7 (A2) x 2 4. Figure 5 2. Hang array center (AA or BB) onto mounting tab on arm assembly (Z) faceplate.
K4W120-210-310 7. Installation Instructions Use two #10-32 x 1/2” Phillips pan machine screws (D1) and two handle clamps (G) to secure handle (H) to array center (AA or BB). (See Figure 10) Display Installation Faceplate Positioning (K4W120 only) IMPORTANT ! : Faceplates should be positioned prior to attaching displays for the K4W120 as the height cannot be adjusted with the displays attached to the faceplates. (K4W310 shown) 1. Loosen height adjustment screws for each faceplate to adjust height.
Installation Instructions K4W120-210-310 WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located on the K4W Series mount up to (and including) the display does not exceed 15 lbs (6.8 kg) per display. CAUTION: Using screws of improper size may damage your display! Proper screws will easily thread into display mounting holes.
K4W120-210-310 4. Installation Instructions Pick up and align display so that screws (N or M) (installed on the back of the display in the previous step) fit into the mounting holes on the faceplate. Lower the display firmly into place. (See Figure 16) Wall Cover Installation CAUTION: Wall covers are fragile and may be damaged or broken if installed with excessive force! Use caution when installing and removing wall covers. (N or M) x 2 3 (Q or R) x 2 1.
Installation Instructions K4W120-210-310 Pivot Adjustment (Column Arm) Display Height Adjustment (K4W120 only) 1. Use handle to extend or collapse column arm (Z) as desired. (See Figure 20) NOTE: Remove display from faceplate in order to expose (Optional) Loosen or tighten column arm pivot tension screws as desired to increase or decrease pivot tension. (See Figure 20) 1. Loosen height adjustment screws for specific display that will be adjusted. (See Figure 22) 2.
K4W120-210-310 Installation Instructions To Reattach Faceplate Assembly K4W120 Faceplate(s) 4. Place faceplate assembly on array arm at desired mounting position. (See Figure 24) Pitch 5. Slide removable plate back into slot at bottom of faceplate assembly. (See Figure 24) 6. Reinstall hex head bolt removed in Step 1 to secure faceplate assembly to array arm. (See Figure 24) 1. Loosen knob on side of center faceplate assembly. (See Figure 26) 2. Adjust pitch as desired. (See Figure 26) 3.
Installation Instructions K4W120-210-310 Cable Management - Covers (K4W210/310 only) 3. Route cables along mounting arms. (See Figure 30) 1. Route cables from display through cable management covers (V) as desired. (See Figure 28) 4. Use cable ties (not included) to secure cables to tie clips (E1). (See Figure 30) 2. Install cable management covers (V) onto array arms (X and Y). (See Figure 28) NOTE: Leave enough slack in the cables so that arm may still swing without resistance from the cables.
K4W120-210-310 Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002326 Rev02 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 06/13 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
