INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation K2P110 K2P120 K2P22H K2P220 K2P Pole Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description K2P Series
K2P Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions K2P Series DIMENSIONS K2P110 1.50" - 1.90" [38.1 - 50.8] 0.78 19.8 INTERFACE ROTATION RANGE 90 TILT RANGE UP 15 DOWN MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 7.42 188.5 K2P120 1.50" - 1.90" [38.1 - 50.8] 0.78 19.8 INTERFACE ROTATION RANGE 90 TILT RANGE UP 15 DOWN MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 10.70 271.
K2P Series Installation Instructions K2P220 1.50" - 1.90" [38.1 - 50.8] 0.81 20.6 MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 INTERFACE ROTATION RANGE 90 K2P22H 0.78 19.8 INTERFACE ROTATION RANGE 90 MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 UP 10 DOWN 9.85 250.
Installation Instructions K2P Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Beves
K2P Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 3/16” (included) 1/8” (included) 5/32” (included) PARTS A (1) [Pole clamp arm] (K2P110 shown) B (4 or 8)* M4x14mm C (4 or 8)* M4x25mm D (4 or 8)* M10x5.
Installation Instructions K2P Series Assembly And Installation Connecting to Pole 1. Determine approximate location for mount keeping in mind display size, extension, height adjustment requirements. 2. Place mount (A) against pole with clamp (E) on opposite side of pole. (See Figure 1) 2 (J3) (J8) x 2 (J9) (E) (J5) (J1) 1 (J10) (J11) or 3 (F or G) x 4 (J4) (J12) (A) Figure 1 3. Using 5/32” hex key (K) and appropriate length screws, loosely attach assembly to pole clamp (E).
K2P Series Installation Instructions K2P110, K2P120 AND K2P220 Recessed Mounting Holes NOTE: K2P22H mount has K1 Series faceplates on array arm. 1. Ensure Centris bracket is able to swivel and tilt easily, yet still be tight enough to hold display in desired position. Adjust as required before proceeding. See “ADJUSTMENT” for detail. 2. Carefully place display face down on protective surface. 3. Place the four spacers (D) over each of the mount holes on the back of the display. (See Figure 4) 4.
Installation Instructions K2P Series WARNING: Only remove display from mount when the display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! See Display Removal section for details. 2. Carefully place display face down on protective surface. 3. Connect faceplate to display 4. Position display with faceplate attached above mount. (See Figure 8) 5. Slide faceplate onto mounting head until quick release tab clicks into place.
K2P Series 3. Installation Instructions Position handle (J2) at desired height and secure by tightening button head cap screws attaching handle brackets to array. (See Figure 10) 3 x4 Adjustments - K2P22H models only 1. Loosen knobs securing faceplates to array. (See Figure 12) 2. Slide displays laterally on array to adjust lateral shift. (See Figure 12) 3. Adjust pitch and pivot position as desired. (See Figure 12) 4. Tighten knobs to secure faceplates in position.
Installation Instructions K2P Series Swing Arm Pivot Adjustment Array Models 1. Adjust pivot position as desired. (See Figure 14) 1. Install cable clips (J7) to back of array. (See Figure 16) 2. Adjust pivot point tension screws to change pivot adjustment tension. (See Figure 14) 2. Route cables through cable clips (J7) as desired. (See Figure 16) 1 (J7) 2 pivot point tension Figure 14 Cable Management Non-Array Models 1. Route cables through cable management channels.
K2P Series Installation Instructions USA/International Europe Chief, a products division of Milestone AV Technologies 8800-002482 Rev00 2014 Milestone AV Technologies www.chiefmfg.com 03/14 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
