INSTALLATION INSTRUCTIONS Istruzioni di installazione Installatie-instructies Instructions d´installation Instrucciones de instalación Installationsanleitung Instruções de Instalação K2W100 K2P100 K2C100 K2W200 K2P200 K2C200 Monitor Arm Series Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description K2 Series
K2 Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions K2 Series DIMENSIONS K2C100 188.1 7.41 (8.85 [224.7] FOR LOWER PROFILE INSTALL) LOWER PROFILE INSTALL EXTENSION 100 3.94 75 2.95 MAX 19.2 [487.7] PITCH TENSION KNOB PITCH RANGE 15 90 INTERFACE ROTATION MANUAL HEIGHT ADJUSTMENT RANGE 244.5 9.63 289.7 11.41 MAX 21.04 [534.2] LOWER PROFILE CABLE MANAGEMENT HEIGHT ADJUSTMENT KNOB DESKTOP THICKNESS RANGE 12.7 .50 MAX 3.25 [82.6] 76.2 3.00 131.7 5.19 K2C200 MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 28.8" [731.
Installation Instructions K2 Series DIMENSIONS (CONTINUED) K2W100 100 3.94 75 2.95 90 INTERFACE ROTATION PITCH RANGE 15 EXTENSION MIN 2.98 [75.7] MAX 17.2 [436.9] PITCH TENSION KNOB 149.6 5.89 263.7 10.38 5.508 81.7 3.22 CABLE MANAGEMENT 61.6 2.43 K2W200 MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 28.25" [717.6] 100 3.94 75 2.95 90 INTERFACE ROTATION EXTENSION MIN 2.98 [75.7] MAX 17.2 [436.9] PITCH RANGE 15 PITCH TENSION KNOB 147.7 5.81 142.6 5.61 81.7 3.
K2 Series Installation Instructions DIMENSIONS (CONTINUED) K2P100 POLE CLAMP RANGE 1.50 [38.1] - 1.90 [48.3] 78.8 3.10 MAX EXTENSION 16.60 [421.6] 100 3.94 90 INTERFACE ROTATION 75 2.95 PITCH TENSION KNOB PITCH RANGE 15 10.484 CABLE MANAGEMENT K2P200 POLE CLAMP RANGE 1.50 [38.1] - 1.90 [48.3] MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 28.25" [717.6] EXTENSION RANGE 2.98 [75.7] 16.48 [418.5] 100 3.94 75 2.95 90 INTERFACE ROTATION PITCH RANGE 15 10.
K2 Series Installation Instructions LEGEND 6 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Be
K2 Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 3/16" (included) 5/32" (included with K1P Series only) PARTS A (1) [monitor arm] (K2W100 shown) B (4 or 8)* M4x14mm C (4 or 8)* M4x25mm *8 screws and washers included with dual arm mounts D (4 or 8)* M10x5.
K2 Series Installation Instructions Assembly And Installation IMPORTANT ! : IF you will be installing a SINGLE display with RECESSED mounting holes, then proceed to "DISPLAY INSTALLATION" before continuing with this mount installation procedure. 1 Connecting K2C Series (column mount) to Desk Standard Installation 1. Loosen clamp screw until enough space is created between clamp and mount to allow for desk mounting. (See Figure 1) NOTE: If space is limited behind desk (i.e. against wall, etc.
K2 Series Installation Instructions (E) set screw 6 3 3/16" x 2 1/2" side view 5 4 (F) x 2 (E) (G) x 2 Figure 5 Connecting K2W Series (wall mount) to Wall 1. Determine mounting location on wall. 2. Use a stud finder to locate stud. 3. Use wall bracket to mark and drill two 3/16" x 2 1/2" holes in wall at desired mounting location. (See Figure 5) 4. Use two 1/4-2 1/2" hex head lag screws (F) and two 1/4" washers (G) to install wall bracket onto wall.
K2 Series Installation Instructions Display Installation Recessed Mounting Holes The mounting holes on the back of the display will either be flush with the back surface or recessed into the back surface. Refer to the applicable installation procedure. 1. Ensure Centris bracket is able to swivel and tilt easily, yet still be tight enough to hold display in desired position. Adjust as required before proceeding. See "ADJUSTMENT" for detail. Flush Mounting Holes 2.
Installation Instructions K2 Series Pivot Adjustment Range Swing Arm Pivot Adjustment Single Arm Models (K2C100, K2W100 and K2P100) 1. Adjust pivot position as desired. (See Figure 12) 1. 2. Adjust pivot point tension screws to change pivot adjustment tension. (See Figure 12) Adjust arm angle as desired up to 90 degrees in either direction.
K2 Series Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002060 Rev 03 2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 12/11 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No.