INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação K1D120 Istruzioni di installazione Installatie-instructies Instructions d´installation K1D120XXDL K1D220 K1D22H K1D220XXDL K1 Desk Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description K1D Series
K1D Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions K1D Series DIMENSIONS K1D120 1.83 46.4 90 TILT RANGE UP 10 DOWN DYNAMIC HEIGHT ADJUST RANGE 23.20 10.20 589.3 259.1 1.81 46.0 MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 DESKTOP THICKNESS RANGE 2.50 0.50 63.5 12.7 K1D120XXDL FULL UP/DOWN = MIN 5.17 131.3 90 TILT RANGE UP 10 DOWN QUICK RELEASE DELL INTERFACE DYNAMIC HEIGHT ADJUST RANGE 1.81 46.0 DESKTOP THICKNESS RANGE 2.50 0.50 63.5 12.
K1D Series Installation Instructions K1D220 DYNAMIC LIFT ARM LENGTH RANGE STRAIGHT = MAX FULL UP/DOWN = MIN 10.21 7.12 259.3 180.9 6.75 171.5 2.31 58.7 INTERFACE ROTATION RANGE 90 MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 UP 10 DOWN DYNAMIC HEIGHT ADJUST RANGE 24.89 11.89 632.2 302.0 DESKTOP THICKNESS RANGE 2.50 0.50 63.5 12.7 K1D220XXDL 0.81 20.6 INTERFACE ROTATION RANGE 90 QUICK RELEASE DELL INTERFACE TILT RANGE UP 10 DOWN DYNAMIC HEIGHT ADJUST RANGE DESKTOP THICKNESS RANGE 2.50 0.
Installation Instructions K1D Series K1D22H 6.75 171.5 INTERFACE ROTATION RANGE 90 DYNAMIC LIFT ARM LENGTH RANGE STRAIGHT ARM = MAX FULL UP/DOWN = MIN 10.21 7.12 259.3 180.9 MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 UP 10 DOWN 1.81 46.0 DYNAMIC HEIGHT ADJUST RANGE DESKTOP THICKNESS RANGE 2.50 0.50 63.5 12.
K1D Series Installation Instructions LEGEND 6 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro B
Installation Instructions K1D Series TOOLS REQUIRED FOR INSTALLATION #2 3/16” (included) 1/8” (included) PARTS or A (1) [Desk clamp arm] (K1D120 shown) A (1) [Arm with Interface] (K1D120BXDL shown) * - (single display models/dual display models) B (4/8)* M4x14mm E (1) [Clamp bracket] C (4/8)* M4x25mm F (1) 5/16-18” D (4/8)* M10x5.
K1D Series Installation Instructions Assembly And Installation Grommet Hole Option Connecting Desk Clamp Arms to Desk Standard Installation NOTE: K1D clamp mounts may be installed directly to 1. grommet holes between 1 1/4” and 2 1/2” in diameter. If grommet hardware (E-G) is used, they can be installed to grommet holes between 3/8” and 2 1/2” in diameter. Loosen clamp screw until enough space is created between clamp and mount to allow for desk mounting.
Installation Instructions K1D Series Using Grommet Hardware Array Installation (K1D22H ONLY) 1. Remove desk clamp from mount by loosening button head cap screw until clamp is completely disengaged from the bolt. (See Figure 5) 1. Slide rotational spacer (J10) into opening on array attachment bracket. (See Figure 7) 2. Maneuver clamp so that it is totally removed from desk mount. (See Figure 5) 2.
K1D Series Installation Instructions Display Installation - Standard Faceplate NOTE: If installing mount that includes custom faceplate (for flush mounting holes) (K1D120XXDL or K1D220XXDL), proceed to Display Installation - Custom Faceplate Section. 1. quick release faceplate Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount.
Installation Instructions K1D Series 4. Position display with faceplate attached above mount. (See Figure 11) 5. Slide faceplate onto mounting head until quick release tab clicks into place. (See Figure 11) 3. Slide base of monitor towards mount until lower tabs secure display to mount. An audible “click” should be heard.
K1D Series 3. Installation Instructions Position handle (J2) at desired height and secure by tightening button head cap screws attaching handle brackets to array. (See Figure 15) 3 NOTE: Tension may also be adjusted with upper tension adjustment screw inside cable management cover and 1/8” hex key (L). (See Figure 17) x4 Reduce tension (lighter display) Increase tension (heavier display) 3 3 Do NOT over-tension adjustment tension screw.
Installation Instructions K1D Series 5. The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor. (See Figure 19) 6. Use 3/16” hex key (K) to adjust rotational adjustment screw to adjust rotational tension. (See Figure 19) 7. The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor. (See Figure 19) 8.
K1D Series Installation Instructions Display Removal - Standard Faceplate WARNING: Only remove display from mount when the display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! (See Figure 22) 1. Make sure display is in the upright position. 2. Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount.
Installation Instructions K1D Series Dual Arm Models 1. Adjust arm angles as desired within a 90 degree range from the pivot point of the arm and a perpendicular centerline of mount. (See Figure 26) 3 WARNING: Swinging the arm beyond this range may result in the mount slipping of the desk causing serious injury! 2 pivot point of the arm (top view) cable (typical) 4 3 2 4 perpendicular centerline 90 degrees range of motion per arm Figure 28 Figure 26 Cable Management 1.
K1D Series Installation Instructions USA/International Europe Chief, a products division of Milestone AV Technologies 8800-002478 Rev02 2014 Milestone AV Technologies www.chiefmfg.com 06/14 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
