User Manual

ManualsBrandsChicony Electronics ManualsElectronicsRF Remote Controller

A. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to

Part 15 the FCC rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

WARNING:

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or

modifications not expressly approved by the party responsible for compliance could void your authority to

operate the equipment.

CAUTION: AVOID PROLONGED USE OF THE REMOTE WITHOUT BREAKS.

Take regular breaks and keep a good posture. Consult your physician promptly if you notice any lost of motion

or pain in your wrist when using the remote.

B. PRODUCT SPECIFICATION

1 Frequency band : 2402MHz-2479 MHz

2 Frequency modulation : GFSK mode

3 Transmitter power : 0dBm

4 Power Requirement: 2V~3.2V

5 Battery: Remote Control : 2 pieces of AAA Batteries

6 Operation distance :Remote Control: 10 M without signal disturbance and no direction limit.

7 Operating temperature : -10

C~ +40

8 Storage temperature : -40

C ~ +90

Summary of content (8 pages)

PAGE 1
A. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to Part 15 the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 2
Contents Getting Started.............................................................................. .................................... 1 Features............................................................................. ............................................... 1 Preparing Remote and Receiver..................................................................... 1 Hardware Installation......................................................................... ...............................
PAGE 3
properly ……........................................................................ ......... 3 Cleaning the remote .. ........................................................................... .............................4 Troubleshooting and Tips................................................................................... ............... …5 English Getting Started Thank you for choosing this Wireless Remote set.
PAGE 4
other electrical devices may influence your receiver sensitivity. 4 Put two batteries into your remote battery chamber Setp 2: Insert batteries 1= Cover 2= Battery compartment 3 3= Channel setting button Setp 3: Connect Remote to your receiver ٛ Push the connect button on the top of receiver. The indicator on the top of receiver will start blinking.
PAGE 5
Setting ID on remote ٛ (1) Push the connect button on the top of receiver. The indicator on the top of receiver will start blinking. ٛ (2) Hold down the connect button inside the battery compartment of the remote for 3 seconds. The ID will be changed after the button released.
PAGE 6
PAGE 7
How to use the remote properly The remote is ergonomically designed to ensure ease-of-use. Inconvenient positioning of your remote, awkward arm movements or posture, working with the remote for lengthy periods without a break can lead to, fatigue, and potential damage to nerves, muscles, and finger joints. You can considerably reduce the risk of injury if you follow the simple rules below. ٛ The distance between the remote and the edge of the desk should be 5 to 10 cm.
PAGE 8
The remote does not operate following installation or is not recognized. ٛ Make sure that the batteries have been inserted correctly according to the polarity and the receiver is well connected. ٛ Check that your USB port is configured properly. ٛ Check whether the respective channels and ID are set on the receiver remote. ٛ Make sure the batteries are not too weak. ٛ Remove the batteries from the device.