9.2V 1/2” Cordless impact wrench Model 65817 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual.
Contents Important SAFETY Information............................. 3 General Safety Rules.................................................. 4 Work Area....................................................................................4 Electrical Safety..........................................................................4 Personal Safety...........................................................................4 Tool Use and Care.......................................................................
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
General Safety Rules WARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1. Work area safety a. Keep work area clean and well lit. Cluttered or dark areas invite accidents. b.
d. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. e. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. 4. Power tool use and care a. Do not force the power tool. Use the correct power tool for your application.
3. Do not lay the tool down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your control. 4. When using a handheld power tool, maintain a firm grip on the tool with both hands to resist starting torque. 5. Do not leave the tool unattended when it is plugged into an electrical outlet. Turn off the tool, and unplug it from its electrical outlet before leaving. 6.
11. Only use the included battery to power the Inpact Wrench. Never attempt to use a battery from any other powered tool in place of the battery for this tool. 12. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these instructions.
3-Prong Plug and Outlet Outlets for 2-Prong Plug Double Insulated Tools: Tools with Two Prong Plugs 1. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Outlets for 2-Prong Plug.) 2.
7. Make sure the extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOLT) NAMEPLATE AMPERES EXTENSION CORD LENGTH (at full load) 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.
Specifications Charger Input 120 V~, 60 Hz, 1.8 A Charger Output 7.2 - 24 V, 1.5 A Charge Time 5 hours (Initial) 3-5 hours (Recharging) Speed 0-2300 RPM Maximum Torque 220 ft-lb Battery Cell Type NiCd, 1700 mAh, 1.2 V, Item 96756 Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
Trigger (36): Squeeze the Trigger to turn the Impact Wrench on and release pressure on the Trigger to turn the Impact Wrench off. Forward/Reverse Switch (32): The Forward/Reverse Switch allows you to change the rotational direction of the Impact Wrench. For a clockwise rotation, move the Forward/Reverse Button to the right. For a counterclockwise rotation, move the Forward/Reverse Button to the left.
3. When the Battery requires recharging, a 3-5 hour charge allows the tool to operate at full power. 4. Slide the Battery off the handle of the Impact Wrench. Insert the Battery into the socket of the Charger (39). Then plug the Charger into the nearest 120 volt, grounded, electrical outlet. 5. Verify that the RED Charging Indicator Light comes on. If it does not illuminate, check the power connection or try a different electrical outlet. Charge the Battery for 1-3/4 hours.
7. When finished, release the Trigger to stop the Impact Wrench. Then, remove the Battery and socket from the tool. 8. Make sure to store the Impact Wrench in a dry, clean location out of reach of children and other unauthorized people. Maintenance And Servicing WARNING Risk of serious personal injury from accidental starting or electric shock.
4. When installing the Carbon Brushes, make sure the carbon portion of the Carbon Brushes contact the Motor’s Rotor and that the springs face away from the Motor. Also, make sure the springs operate freely. 5. After replacement or cleaning, replace the two Brush Holder Caps. NOTE: New Carbon Brushes tend to arc or spark until they wear and conform to the Motor’s Rotor. Troubleshooting Problem Possible Causes Possible Solutions Trigger Switch locked in place. 1.
PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product.
ASSEMBLY DIAGRAM 38 Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 65817 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
