Portable Sound System OPERATION MANUAL GREEN PRODUCT It has been RoHS Compliant Chiayo Electronics Co., Ltd. Office：No.30, Lane 27, Sec.4, Jen-Ai Rd, Taipei 10685, Taiwan Tel：+886-2-2741-5741 Fax：+886-2-2752-5242 Factory：No.88, Chung-Hsiao St.2, Chiayi 60085, Taiwan Tel：+886-5-271-1000 Fax：+886-5-276-7611 Email：sales@chiayo.com.tw Web：www.chiayo.com.
SMART 300 Operation Manual Accessories Congratulation and thank you for the purchase of this all-in-one ultra compact portable sound system. To ensure a trouble-free operation, please read this manual thoroughly to fully understand its controls and functions. There are various versions of the SMART 300 as follow : 1. SMART 300 Passive Speaker. (Fig.1) 2. SMART 300 portable sound system only ( VHF / UHF ) ( Fig.2 ) 3. SMART 300 with Digital USB player. ( VHF / UHF ) ( Fig.
Federal Communication Commission Interference Statement SMART 300 ( Amplifier version configuration ) SMART 300 Passive Speaker This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules .These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Operating procedures Caution and tips on how to obtain the best results. After unpacking the unit for the first time, please charge the unit for about 4~5 hours before any operation. This is absolutely necessary as the built-in rechargeable battery might have been discharged naturally due to long shipment and storage time, even though it has been fully charged in the factory prior to shipment.
Operating the dynamic wired microphone There is a MIC IN jack with dedicated volume control for this portable sound unit. To use a cable microphone ( dynamic only ), just plug the end with a phone jack plug into MIC IN . Switch on the Power / volume control knob MIC ( H ) and rotate it clockwise, amplified sound could be heard when voice is spoken into the cable microphone. Operating the Digital USB Player To use the USB 2.0 Player for playing MP3 files, simply plug your USB 2.
Handheld Transmitter Q-1002(VHF) Making changes to various settings in SM-5016 Par ts an d fun ct ion s 1.Making changes to CHANNEL / FREQUENCY: Use UP or DOWN button to go to the CHANNEL /FREQUENCY page. Battery compartment cover Battery status LED indicator Color cap Metal Grille ( Capsule module inside ) The cursor will flash to allow changes to be made. Pressing UP or DOWN button will increase or decrease the channel number. The corresponding frequency will change accordingly.
Hand-held microphones SQ-916(UHF) Belt-pack Transmitter SM-5016 (UHF) Antenna Battery weak / audio mute indicator Audio mute switch Mini-XLR connector Power ON / OFF switch LCD display Mini USB port Cover release button Charging contacts 10 Lavalier microphone 11 Mic clip 8 SQ-916 1. Capsule with metal grille 2. Battery indicator 3. Sensitivity switch 4. Power on/off switch 5. Battery cover 7.
Changing capsule Installation of cable restraint This microphone has a module design. To change or replace a capsule, Open the grill to pull out and plug in the capsule as shown in the following figure. To prevent contact noise caused by constant tension applied to the connector, a cable restraint is designed such that tension is totally reduced when it is properly used.
Handheld Transmitter SQ-5016(UHF) Beltpack Transmitter SM-916 (UHF) Battery installa tio n Antenna Parts and functions SM-916 uses a 9V batte ry. To insert the batte ry, first open the batte ry compartm ent cover by pressing the cover downward till the door flips open by itself (see below picture). When installing Battery status Indic ator the batte ry, please beware of correct polarity .
Making changes to various settings in SQ-5016 Beltpack Transmitter M-1002 (VHF) 1.Making changes to Channel: Use UP or DOWN button to go to the CHANNEL/ FREQUENCY page. The cursor will flash to allow changes to be made. Pressing UP or DOWN button will increase or decrease the channel number. The corresponding frequency will change accordingly. When a desired channel is selected, it will be automatically saved and stored in the memory. Par ts an d fun ct ion s Power Switch Battery status indicator.
