Prefacio ADVICE Este manual de usuario se define claramente el acuerdo entre Chery Automobile Co., Ltd. y su clientes sobre la garantía de calidad del producto, y el establecimiento y la terminación de los derechos y obligaciones en el servicio post-venta. Por favor, lea atentamente este manual del usuario antes de utilizar las partes fabricado por la empresa Chery. Manual del CHERY QQ3 del usuario Se le felicitó sinceramente ser un dueño de Chery QQ3! Gracias por su creencia de Chery Automobile Co.
Prefacio Declaración Importante Este Manualis elaborada de conformidad Antes de utilizar los productos, por favor con las características estructurales de Lea atentamente el manual, que su QQ3 fabricados por Chery Automobile derechos para disfrutar de los servicios Co., Ltd .. Este manual se aplica a la de garantía a partir de nuestra corporación QQ3. se pierden debido a la violación de las Este manual incluye la información más disposiciones operativas. reciente hasta que se imprime.
Breve Introducción Capitulo 1 Breve Introducción 3
Breve Introducción Antes de la lectura de este manual de instrucciones, usted deberían aprender sobre lo siguiente: Gracias por su compra de un Vehículo Chery. Para ayudarle a utilizar el coche correctamente y asegurar su beneficio, por favor tome tiempo para leer este manual cuidadosamente. Este manual contiene algunos información importante para todos los días operación y mantenimiento normal. Está diseñado para ayudarle a serfamiliarizarse con el funcionamiento de su coche.
Breve Introdución de modelos, o sólo en cierta suministrado mercado. la información se ha mencionado anteriormente. completar la compra. Rodaje de un Nuevo Vehículo Si ve este símbolo en su vehículo, antes de cualquier operación, usted debe leer los capítulos relativos a este manual. Seguridad y protección del medio ambiente Nosotros necesario hombro nuestro responsabilidades obligatorias y obligaciones en el esfuerzo de protección del medio ambiente.
Breve Introducción In general, it shall not exceed 100km the red indication area, it must switch into necessary. Under such circumstance, when / h; the adjacent high gear. driving during the first 100 km, it ought to Each gear shall avoid running at full Unnecessary high speed of engine should throttle. be avoided. Change up as soon as possible Specification of Running in within the Range of 1,000 - 1,500 KM: be relatively slow, and the driver should be extraordinarily cautious.
Brief Introduction wheel is replaced or a wheel nut has ever been loosened, after 800 km of cruise, the wheel nut should be again screwed down according to specified torque value. One-to-One Service To provide better vehicle services as well as app lication, a Chery vehicle dealer will appoint one service consultant for you when you purchase a car. If you have any problems during the process of driving, please contact your consultant, who will provide you with high quality services.
Brief Introduction Vehicle Delivery and Inspection Record: This vehicle's delivery inspection has been finished in accordance with the provision specified by Chery Company Limited, and the quality conforms to the technical specification of Chery Company. And the certification is presented herein.
Brief Introduction Date of Vehicle Delivery: Seal of dealer Vehicle Model Body VIN number Engine No.
Brief Introduction Vehicle Sales and Devlivery Card of CHERY Performance of Complete Vehicle Category S/N Item Whether inspected and clarified or not No □ □ No □ □ No □ No □ □ No □ Yes □ No □ Speedometer, tachometer, and odometer. Yes □ No □ 8 Wheel house, spare tyre in luggage boot, tool box and User’s M anual for complete vehicle. Yes □ No □ 9 Seat belt, seat, cigarette lighter, A/C switch and duct, glove box and sun visor.
Common Sense of Application Brief Introduction 1 93# gasoline for fuel Yes □ No □ 2 Proper use in running-in period Yes □ No □ 3 Operation of complete set of vehicle lights Yes □ No □ 4 M eanings of warning light.
Brief Introduction “One-to-One” Consulting Service Card Date of Purchase: M odel: The following items shall be confirmed by the owner. II. Introduction of “one-to-one” consulting service mode (" √" for yes and"×" for no) □Always contact your service consultant if the owner has any problem or requirement, while not someone else □The service consultant is the only person who is designated by the service station to communicate with the owner III.
Brief Introduction “One-to-One” Consulting Service Card Date of Purchase: M odel: The following items shall be confirmed by the owner. II. Introduction of “one-to-one” consulting service mode (" √" for yes and"×" for no) □Always contact your service consultant if the owner has any problem or requirement, while not someone else □The service consultant is the only person who is designated by the service station to communicate with the owner III.
Notices Before Drive Description of Common Symbols on Vehicle S ymbol Definition CHECK ENGINE Glass Drive Switch Prohibitted Rear Fog Lamp S ymbol Definition Antilock S ymbol braking system Position light Engine oil pressure Safety warning Throttle Definition warning light fault indicator lamp Coolant temperature overhigh warning light (red) Coolant temperature Front Fog Lamp Cigarette Lighter normal indicator (green) A/C Air System Conditioning Brake warning light system Iden
Notices Before Drive S ymbol Definition Battery Hazard S ymbol warning brake Air bag Horn Vehicle maintenance Battery positive Headlamp switch Definition Windshield washing flasher Low beam indicator light Definition Seat belt ready High beam Parking S ymbol indicator fault Windshield indicator light defrosting/defogging Fuel level low Inner circulating air 6
Notices Before Drive S ymbol Definition S ymbol Rear Lockup indicator light windshield heating indicator S ymbol Definition Outer circulating air Indicator for interior Unlock indicator Warning Definition lamp switch for door and trunk lid Audible alarm op en Right turn lamp indicator signal Left turn signal lamp indicator 7
Notices Before Drive Notices Before Drive 8
Notices Before Drive 9
Notices Before Drive Operations in the phase of test-drive engine, but also increase fuel and oil consumption and even damage engine components. And especially try to avoid stepping down accelerator pedal to the end under bottom gear. Some simple protective measures should be followed during the initial running-in period which can improve drivability and economy of the vehicle and prolong its service life.
Notices Before Drive rack, or it will limit the back line of sight and Keys Equip two keys adapted to all lockholes on the car, and one of them is a spare key. Key code card of the key is pasted on the number cap. Do not leave code card in the car for car’s safety. Put it at a safe place an d remember key code. Do not record key code in the car to prevent anyone who got this code to copy the key without permission. ！Notice Do not leave the key in the car. 1. Lock the car. 2. Take the key with you.
Notices Before Drive can pull the inner handle. Unlock Lock When opening the door from outside, you can pull the outer handle. When opening the door from inside, you simultaneously. ！Notice Before leaving the car, lock the left-front door when there is no one to take charge. ！Notice Do not leave children or animals alone in the car. 1.To prevent asphyxiation especially in hot seasons. 2.They may move the car unexpectedly.
Notices Before Drive Children Security Lock On each of the back door there is a children security lock which can prevent the passengers at the back, especially the children to open the door from inside unexpectedly by pulling the inner h andle. has been locked so as to prevent any damage to the handle. Burglarproof Entering System Unlock No-Key No-Key Entering System can open the door in a distance of 6 meters through a sensor. The LBD on the sensor lights up to indicate the sensor in operation.
Notices Before Drive Activating door Lock and Burglarproof Mode Close all the windows; Turn ignition key to B, and pull out the key; Let all passengers get off the car. Relief of Door Lock and Burglarproof Mode Press UNLOCK button on the sensor to unlock all doors and hazard warning lamp glitters twice at the same time, burglarproof mode is exited. Close all doors and hoods and trunk lid. Press down the LOCK button on the sensor so as to lock all of the doors.
Notices Before Drive environment: Do not drop the waste battery as living garbage; Dispose the waste battery according to the local reclaim regulations.
Notices Before Drive The sun shading top can not open when there is sundries on it. Clean the top before open it. Eliminate the water drops, snow, ice and sands before opening the sun shading top. Do not place anything heave on the sun shading top or around. Please close the sun shading when leaving the car alone. Outer Rearview Mirror Adjust the outer rearview mirror to see both sides of the road clearly and confirm the position of the things you saw.
Notices Before Drive closer, so use inner rearview mirror to clear the rear line of sight. Do not block the rearview range from the driver seat. The outer rearview mirror at the passenger side is a convex, so things you see in it will be closer than what it is actually. Use this mirror you can watch much wide of the road behind you. When entering a narrow roadway or washing your cars, you can push back the mirror which will properly collapse to the body.
Notices Before Drive anything under the seat which will disturb the seat adjustment organ. danger of hurting the cervix. You can adjust its altitude by pulling up or press down it. Front Seat Tilt Adjustment Pull up the joystick at the side of the seat to adjust the backrest to an ideal angle, and then loose the joystick. ！Notice Do not adjust the driver seat during driving so as to prevent the car to be out of control. The looseness of the seat belt will reduce its protection function.
Notices Before Drive notch of the left guide bushing. Touch the head of the stop perch with the screwdriver and pull the headrest out from the bushing. Folding process: Lift the seat cushion to vertical. Pull up the lock button on the seat backrest, loose the backrest, and fold in the direction of front and down. If you want the seat backrest get back to the vertical position, just Folding Backseat Backrest Fold down the backrest to increase the space of the trunk.
Notices Before Drive Seat Belt Measure Precaution To protect the passenger, the entire passenger must correctly use seatbelt during driving. One seatbelt for only one person, and those children under 6 years old are not suitable to use seatbelt, and you should assembly proper child seat or assistant cushion for your child. ！Notice Passengers may get hurt in a collision or emergent stop, so they must use seatbelt at anytime. Do not use one belt by several people.
Notices Before Drive ！Notice The worn seat belt may cause serious damage, so check the seat belt components regularly. After a collis ion, you must take all the seat belt components to the Chery Service Station for a check and replace them according to the need. If the belt has been damaged or polluted, it must be replaced. After a serious collision, the seat belt components must be replaced no matter there is evident damage or not. If the seat belt is not suitable, it will arouse much more serious damage.
Notices Before Drive Three point seat belt There is three points seat belt with brake limit on every Chery car. Although the spring-plugged seat belt is coop erated well, the body is permitted to move freely during a smooth running. There is a sensitive reel on the seat belt which is used to lock the seat belt in violent acceleration and deceleration. Please do not test the lock of the seat belt by rush forward forcibly.
Notices Before Drive expand, the excess damage proved that the car had absorbed a great deal of bounce energy, so there is no need for air bag. In other serious collision accidences, such as collision at the chassis, the body may not be damaged in large scale but also will cause the air bag explode. ！Notice M isusing the seat belt may cause serious damage. Put the connecting belt on the buttocks comfortably rather than on the stomach or the waist.
Notices Before Drive The air bag will not operate under the following circumstances: Tracing tail, side bumping, side turn and without enough bumping intensity. Cab air bag The driver air bag is assembled at the central flange of the steering wheel. The air bag will charge and expand in several seconds after collision and form a safe air cushion for the driver. The air bag can expand with enough power and speed, so it is very important to adjust the driver seat and backrest properly.
Notices Before Drive Trunk cover the left side under the driver seat. Notice when filling the fuel: 1. Shut down the engine. 2. Pull up the fuel fill door unlock joystick to open the fuel fill door. 3. Turn in counterclockwise to open the fill cap. 4. Turn the cap clockwise after filling and screw down, then close the fuel fill door. unlock joystick Pull up the trunk cover unlock joystick at the left side under the driver seat to open the trunk cover.
Notices Before Drive ！Notice The fuel steam is flammable. Shut down the engine and do not smoke or produce fire and sparkle to avoid fire. Engine Coping 2. Push upward of the claw to lift the engine coping. 1. Pull the unlock handle at the left side under the instrument panel to open the engine coping lock. Do not use plumbic gasoline to the non-plumbic gas cars to avoid any damage to the engine and e xhaust system. Gasoline will damage the painting.
Notices Before Drive the hole beside the engine room to brace the coping. 4. Press the knighthead into the clamp to avoid vibration before closing the coping. 5. Lay down the coping and let it fall from about 30cm (1 inch) height. Close the coping and shake the edge of it to ensure it has been locked. ！Notice Opening the engine coping in traveling will cause accident which would block the front line of sight. Pull the edge of the coping to check whether it has been completely closed before driving.
Notices Before Drive 28
Notices Before Drive 29
Start and Operation Start and Operation 30
Start and Operation 31
Start and Operation Fuel Suggestion Use non-plumbic gasoline with high quality for commercial purpose. The quality of gasoline decisively affects the dynamic, drive performance and life of the engine. And the additive is important to the fuel. Please use non-plumbic gasoline with additive of high quality. If the octane rating is too low, it will cause engine explosion. Chery will not be responsible for any loss caused by misusage of the fuel. Please use fuel with high quality.
Start and Operation Before starting the engine Neutral Pos ition III position Can start motor to drive the engine. Loose the key after starting the engine, the key will back to “II” position automatically ！Notice Do not place the key to “I” or “II” position when the engine is not running to avoid electric loss of the accumulator. Do not pull off or turn the key in driving to avoid the car out of control. M ake sure there is no obstacles around the car.
Start and Operation after waiting for 10 s. If the engine fails to start up in the continuous two times, step on the accelerator pedal to its end and keep it in the position, turn the key to the III pos ition, and then loosen the key after the startup of the engine, subsequently, with the speedup of the engine, slowly release the accelerator pedal. 4.
Start and Operation Neutral Pos ition the engine still fails to start, wait for 15 s and then have a try (for the vehicle equipped with the automatic transmission, turn the ignition switch, wait for 10 s and then have a try) Operation procedure of AMT ) transmission ( Operation procedure to start a engine with AMT transmission ) ( Keep the transmission gear position on the N gear, 1st or 2nd gear befor e the engine starts.
Start and Operation 2. To enter the automatic gearshift mode, press the AUTO key to enter the mode, and press the AUTO key again to enter the manual gearshift mode; 3. In the case of manual gearshift mode, push the selector lever towards the + direction, and then increase the trans mission up to adjacent upper gear position; and push the lever towards the – direction, and then reduce the transmission down to the adjacent lower gear position； 4.
Start and Operation putting into gear, accelerate a little and shift again. ！Notice: If you want to start on a brae, you must pull the parking brake and step slightly down the accelerator panel, loosing the parking brake at the same time. Do not start the car with the hood open. your drive. If the brake pedal is lower than before, you need to adjust the rear drum brake. If this happens, please test your car forward and backward and test the brake in all directions to find out the reason.
Start and Operation to lock. The system detected the wheel speed before locking and control relative brake with electric signal. When opening the ignition switch, the Brake with ABS Do not fear the vibration of the brake pedal. Step down the brake pedal and maintain until starting the ABS no matter how the road status is. ABS adjusts the brake pressure of each wheel for best performance and does not loose direction stability or steering cont rol at the same time.
Start and Operation 1 2 3 Stopping the car Step down the brake pedal and strain the manual brake. When stopping on a horizontal road, set the joystick to neutral gear position. When stopping on a brae (driving down), set the gear joystick to back up. When stopping on the brae (driving up), set the joystick to 1 s peed position. Close all the windows and clearstory. Turn the ignition key to “B”, and pull off the key. Lock all the doors and trunks. Ensure the car has stopp ed completely.
Start and Operation economy and prolong the life of the tire. Keep certain distance with other cars to avoid emergency brake so as to depress the wear and tear of the brake patch and improve the fuel economy(because there is no need for additional fuel to accelerate). Do not load unnecessary goods to add the weight. Do not leave your feet on the pedal which will cause unnecessary worn or even damage the brake and increase the consume of fuel. Keep the condition when the car left the factory.
Start and Operation advices: Start and Operation Drive carefully for the brake distance will be prolonged. Avoid brake or steering. Step slightly on the brake pedal to avoid sliding of the front wheel. Spread some rocks and stones under the front wheel when the car getting stuck in snow or mud, or use tire chain or other antiskid to increase the adh esive power. until it stops during a brake.
Instruments and control devices Instruments and control devices 42
Instruments and control devices 43
Instruments and control devices 44
Instruments and control devices 1.Steering switch 14.Rear window defroster switch 2.Horn button 15.Radio/cassette 3.Cluster gauge 16.Airflow distribution switch 4.Ignition switch 17.Ashtray 5.Wiper switch 18.Package bo x 6.Temperature cont rol switch 19.Cogarette lighter 7.Center ventilation opening 20.Interior and outer circulation control lever 8.Hazard warning switch 21.Accelerator pedal 9.Anti-theft indicator light 22.A/C switch 10.Blower motor switch 23.Brake pedal 11.
Instruments and control devices Speedometer Speedometer ind icates running speed (km/h) Vehicle buzzer speed automobi le warning While vehicle speed exceeds 120 km/h , the vehicle speed warning buzzer will sound ( within specified market) Odometer Fuel gauge The upper counter of odometer records total mileage, while the lower counter records travel mileage. The last digit of the lower counter represents a unit of 100 meters (or l/10 kilometer). Fuel gauge indicates the liquid level of fuel tank.
Instruments and control devices added in time if the warning light is on. Fuel level warning light Fuel will run out soon when the light goes on. The lamp will light up when the remaining fuel in tank drops to 5.5 liters. Once the warning light is on, fuel should be added as soon as possible. Engine malfunction indicator light With ignition switch is turned on, engine malfunction indicator light will light up for about 4 seconds until it goes out.
Instruments and control devices on after the hand brake is released, it indicates a lack of brake fluid. Take the following steps: ！Notice If engine oil pressure warning light stays on, it indicates a failure. If it happens during driving, stop the vehicle to check for the lack of engine oil as soon as possible. Add engine oil if necessary. If there is no problem with engine oil, go to the nearest CHERY AUTO authorized service station for inspection.
Instruments and control devices ABS warning light Generator warning light With ignition switch is turned on, ABS indicator light will light up for about 4 seconds before it goes out. With ignition switch turned on, if the ABS light is not lit or remains on, contact the nearest CHERY authorized service station. It indicates a discharge of vehicle battery. With ignition switch turned on, the light will light up and goes out after engine is started.
Instruments and control devices Turn signal indicator lamp/ hazard warning flasher indicator ！Notice If bulb is blown, replace it immediately for avoiding accident. If green arrow does not illuminate when turn signal switch is switched on, check for blown fuse or bulb. Headlight high indicator light When high beam switch is turned on, indicator light will come on.
Instruments and control devices Foglight/rear switch foglight First position with front foglights on. Second position with front and rear foglights on or only with rear foglights on. With switch in second position, the operation indicator light on switch will illuminate. With ignition switch on,front foglights will op erate only when parking lights are turned on. They may work with high beams or low beams simultaneously. Rear foglight can only be operative with front foglights simultaneously.
Instruments and control devices Transmission oil temperature warning light (for the vehicle with AMT transmission) it examined. Manual mode: Position display (for the vehicle with AMT transmission) In the case of manual mode, the gear position selected by a driver will be displayed in the display with the form of digital. In the following figure, the 2nd gear is taken as an example.
Instruments and control devices traveling time switchover/reset button, and the “ SEL” is a function select button. The profile of this instrument is shown below: Speedometer The speedometer displays the running speed of a vehicle (unit: km/h), with the range of 0–199 km/h, which is displayed in the form of digitals, and the division of display: 1 km/h. Digital instrument ( Odometer With the digital display, the odometer has a overall mileage count er (ODO) which can record the max.
Instruments and control devices Fuel alarm indicator lamp ! CAUTION: When the pointer gets to the red area, the engine may he overheat, and you shall immediately stop your vehicle to cool the engine. In this case, if you drive your vehicle continuously, it may damage the engine. In case that this indicator lamp lights, it indicates that the fuel will be used up soon. When the fuel remained in the tank reduces down to 5.5 L, this indicator lamp lights.
Instruments and control devices Engine oil pressure indicator lamp alarm The indicator lamp lights when the ignition switch is turned on, and extinguishes after the engine starts up. If the indicator lamp lights when the vehicle is traveling, check the level of engine oil. If the engine is short of oil, refill the specified engine oil to the normal level of oil; and if the oil level is normal, please take care to cont act the Chery Authorized Service Station.
Instruments and control devices the fluid level is low, refill the specified brake fluid. 2. check whether the brake works normally or not. 3. slowly drive your vehicle to the M aintenance Center to have it checked if the brakes work normally. 4. drag your vehicle to the Chery Authorized Service Station if the alarm indicator lamp lights for a long time and any brake works abnormally or the brake fluid is found leakage.
Instruments and control devices Airbag alarm indicator lamp (for the models equipped with the air bag) The indicator lamp lights after turning on the ignition switch, and, waiting for approx. 4 s, then extinguishes. It illustrates that the airbag system is normal. If the indicator lamp doesn’t light or the lamp doesn’t extinguish after it lights for 4 s, or blinks continuously and even lights for a long time when the vehicle is traveling, it indicates that the airbag system has trouble(s).
Instruments and control devices Gearshi ft display Manual mode: In the manual gear shift mode, the gearshift selected by the driver will be displayed on the display in the column-shaped form. Automatic mode: Press the “AUTO” button to enter the automatic gear shift mode. In this case, the “AUTO” indicator in the instrument panel will light, and the current gearshift will be displayed on the display in the column-shaped form.
Instruments and control devices (below 50 m). the display mode of “TRIP” and “Traveling Time”. Its specific op eration procedure is as follows: 1. The initial display is TRIP A. If the TRIP A is 1,357.9 km, the TRIP display shows: 2. Press the “TRIP” button once, the TRIP A is switched to the TRIP B. In this case, if the TRIP B is 2,468.0 km, the TRIP display shows: 3. Press the “TRIP” button again, the TRIP B changes to the Traveling Time.
Instruments and control devices once, and then the brightness level will return back to the minimum value. ● Clock’s integral point calibration In case that the clock displayed is within the integral point to or past 2 minutes, press the “TRIP” and “SEL” buttons at the same time to calibrate the integral point of the clock. For instance: When the time displayed is 14:59 but the actual time is just 15: 00, this calibration op eration can immediately calibr ate the clock to 15:00.
Instruments and control devices It means that in the case of “Nighttime Display Brightness” setting status, the left two digitals represent the nighttime brightness setting status mark while the right three digitals represent the set value which can be selected from 1 to 100 and the initial value is min. 001. Press the “TRIP” button once to increase the value by 1, and press the “TRIP” button and keep it, the value will automatically increase by 10.
Instruments and control devices It shows that the mileages remained from the service mileage set are 100 km, 50 km and 0 km respectively. Each reminder is accompanied by the beep sound, with the duration of 10 s. ● Status or initial value of the instruments re-powered after power off Both the positive input of power supply and the positive input of ignition switch POWER OFF, and the relevant data of the instruments will be lost after re-powered on.
Instruments and control devices Passing light switch HIGH= continuous wiping, high speed Fuzzy function Headlight high beam will come on if control lever is turned towards steering wheel, then cont rol lever may be released. Control lever will return to normal position after released. Headlight high beam will remain on when control lever is hold on by driver. Windshield wiper switch With ignition switch turned on, windshield wiper may be operated when control lever is turned upward. OFF=stop.
Instruments and control devices 3／4 of its capacity. Turning control lever in the reverse direction of steering wheel may operate luggage compartment cover wiper and washer. ！Notice For windshield should not be wiped when there is no water in washer tank, so front sight will be affected. Therefore, 1.Stop vehicle to add washing liquid if it is necessary to clean windshield during running.2.Check washing liquid level before a travel. In cold weather, windshield may freeze, which will disturb driver's sight.
Instruments and control devices driveway when a emergent parking or traffic handicapping is avoidless. Hazard warning flashlight switch When hazard warning flashlight switch on dashboard is pressed, hazard-warning flashlight will be turned on and all turn signal light will light up simultaneously. After once more a press, all lights go out at the same time. Hazard warning flashlight may be operated no matter whether ignition switch is turned on.
Instruments and control devices Digital clock After ignition switch is turned on, digital clock will indicate time. There is a button on digital clock which is designed to adjust time when necessary: Press button and hold on for 4 seconds, the hour number on clock will blink frequently. Accordingly, every button press will increase an hour of the time on digital clock.
Instruments and control devices Horn button Cup holder Horn will blow if steering wheel (without airbag) center or the left/right side of steering wheel (with driver's airbag) is pressed. Horn may blow whatever position ignition switch is. Try to avoid using horn. Cup holder is located on front console and designed to hold cup. ！Notice With vehicle running, the liquid in cup may spill out . So do not use cup holder while driving. "on" position:Interior light will remain on despite door is open or not.
Instruments and control devices ！Notice If accident or emergent braking happens during running with glove box cover open, personal injury may be caused, therefore, glove box cover should be shut during driving. Makeup mirror M akeup mirror is located in the back of right sun visor. ！Notice Driver's vision may be disturbed if something is hung on accessory handle, therefore, do not hang anything on accessory handle.
Ventilation and A/C system Ventilation and A/C system 69
Ventilation and A/C system 70
Ventilation and A/C system Control panel Ventilation and heating 1.Temperature control switch 2.Airflow distribution switch 3.Blower motor switch 4.Internal and external circulation control lever 5.A/C switch A/C system regulates temperature by cold and hot air and temperature could remain constant at any speed. Blower decides airflow speed. Blower may be turned on during running if necessary.
Ventilation and A/C system Center ventilation opening Side ventilation opening Air, after being conditioned, is directed into vehicle by two center ventilation openings. Setting grids can change airflow direction Conditioned air is directed into vehicle by two side ventilation openings.
Ventilation and A/C system Temperature switch control Temperature control switch is used to control the air temperature of ventilation opening. Blue position: Cold Red position: Hot Blower motor switch Blower motor switch is used to control blower motor speed (four positions in all). Blower regulates wind speed. Blower may be turned on to improve comfort during driving. Internal and external circulation control lever It is used to select exterior fresh air or interior circulating air.
Ventilation and A/C system Airflow switch distribution Airflow distribution switch is used to select airflow direction. There are five positions for switch: " head and foot" position( ) Air flows out from center ventilation opening and front bottom exhaust opening. Head Head and foot Foot Foot/defrost Defrost " head" position( ) Air flows out from center ventilation opening and side ventilation opening.
Ventilation and A/C system Temperature control switch: turn anti clockwise fully (Blue) Blower motor switch: Full speed A/C system Ventilation, heating and cool ing system parts compose a control system which could (in any cold condition ant at any outdoors temperature) supp ly maximal comfort .A/C system cooling element cools down air and removes moisture and dust such as pollen. A/C switch It is used to turn on or off A/C.
Ventilation and A/C system Internal and external circulation control lever:( Head and foot It is design for transition stage such as at outer low temperature with no sunlight. When temperature control switch is set between cool (blue) and hot (red), hot air is directed to lower space of vehicle and cool air and natural air is directed to upper room.
Ventilation and A/C system Normal heating A/C switch: Off Internal and outer circulation control Temperature control switch: Red Blower motor switch: Random ) lever:( Airflow distribution )or( ) switch:( Temperature control switch: Red Blower motor switch: Random Notice Defrost do not set A/C in ( )or( )position during cooling., For temperature difference between outer air and windshield may be caused and fog, which will disturb sight, may form on the inner surface of windshield.
Ventilation and A/C system 78
Audio system Audio system Note: If vehicle is equipped with system other than the following audio system , read carefully vehicle audio system instruction manual.
Audio system 80
Audio system Function of Baoling Audio Panel (optional) 1.Volume key 6.Automatic Storage Key 11.Tune Key 2.Power on /off key 7.M emory Key 12.Eject Key 3.M ode Select Key 8.Skip Forward Key 13.LCD Display 4.Band Select Key 9.Skip Backwards Key 5.Clock Key 10.
Audio system Introduction to General Buttons Function 1.Power Supply On／Off Key(POWR) One press on (2) key turns power on; once more press on (2) key turns off power (Note: when power is engaged for the first time, Radio/Cassette Player will be in initial Operating M ode due to the Power On Reset of main control chip). 2.M ode Select Key (M ODE) If (3) key is pressed repeatedly, functional mode selection will be performed in the following order. VOL (Volume)-BAS (Bass)-TRE (Tremble)-BL (R.A.L.)-FA (F.A.
Audio system 7.tuning Key( " "、" ") Press the key " " or " " transitorily, stations may be scanned manually step by step ( AM :9KHZ 、 FM :50HZ) until desirable stations are found. Press the key " " or " " more than 1 second; automatic scanning will be enabled until desirable stations are found. If the key " " or " "is pressed during automatic scanning, audio frequency will return to previous frequency. Radio receiving operation 1.Turn on the radio, press power key (2).
Audio system tape play reversely. 6.Switch between receiving and p laying 1. Push tape into cassette holder and receiving mode will change to playing mode. 2. Press Eject Key (12) and tape will be ejected; playing mod e will be switched over to receiving mode. Press Fast Forward or Fast Backward Key ( after fast forward、Fast Backward is finished, radio will return to playing mode from receiving mode). ！notice: In any case, no broken wire is allowed to be bare without insulation.
Audio system VDO Audio Panel Function (optional) 85
Audio system 1.Preset key1 9.Display RANDOM :CD Random Play Start／Stop 10.BAND: Band DISC+: Backward disk selection 2.Preset key2 SCAN: Radio frequency scan／CD play 15. Fast Forward 3.Preset key3 REPEAT: CD Repeat Play Start/Stop track scan 16. Fast Backward 4.SOURCE: Sound source 5.SOUND Short press: sound effect mode SELECT: Lon g press: sound set mode 6.MUTE: M ute 7.Volume 8.Power switch High track, low track search (play) 14.Preset key4 17.
Audio system Audio On/off Press POWER key to switch on or off volume Volume may be regulated by rotating the knob. Warning: It is should be ensured that traffic signal (whistle, siren) could be heard. M ute Press M UTE key to activate or disable mute state. Audio effect Whether or not jazz music, popular music , verbal program , classical or rock music is preferred, SOUND(audio effect) key will meet your requirement.
Audio system Press key to tune to low frequency station or high frequency stations. If another radio station is desirable, press the same key. Search sensitivity (Only FM) -Search sensitivity may be regulated. Refer to " SRCH " items in "settings". Frequency scanning Frequency scanning function enables you to enjoy the local station of every present band for 10 seconds. -Frequency scanning function may be activated /disabled by pressing SCAN key for at least 2 seconds.
Audio system Press key to activate/disable Fast Backward: key to activate/disable Fast Press Backward: -Here Radio/Cassette Player is switched to radio mode. When tape is finished, tape play will be cont inued. M usic search system -Previous/next track select the number of tracks to the track which is meant to skip from p resent track. key to select previous track. -Press -Press key to select next track. -Radio/Cassette Player will remain mute until desirable track is reached.
Audio system Clock setting -Press and hold on SETUP key for at least 2 seconds to enter SETUF menu key to enter into " TIM E " -Press item. -Press SETUP key to select " 12H" or " 24H " key to select hour item -Press -Example of Display:"0000'(24 hour format) or” AM 12:00''(12 hour format) -Hour item begins to blink. -Press SETUP key to adjust hour item key to select minut e item -Press -M inute item begins to blink. -Press SETUP key to adjust minute item -Clock begins to operate from the adjusted time.
Audio system Option or Item Usage [Setting] RADIO [EUROPE,LATAM AM ERICA,ASIA] Select tuning unit according to standards for Europe,Latin America,America FM [6,12,18] Select the number of presented platforms in FMA mode M W (AM ) [ON,OFF] Apply ' OFF ' to turn off M W(AM)when radio is not at work M W (AM ) [6,12] Select the number of presetted stations in M W(AM) mode TUN [AUTO,MAN] Select automatic or manu al tuning SRCH [LO,DX] Select ' LO ' if only clear frequency station is preferre
Audio system 92
Emergency situation Emergency situation 93
Emergency situation 94
Emergency situation Emergency situation Driver's tool、Spare tire Driver's tool and spare tire are all stored in the place for spare tires under luggage compartment floor.
Emergency situation to remove bolts , then remove wheel.. -Install spare wheel in place and tighten wheel bolts clockwise by hand. -Rotate jack anticlockwise to lower vehicle to the ground. Tighten wheel bolts according to requirement on " diagonal " order(1 - 2 - 3 - 4). -Insert jack crank handle into jack and turn jack handle clockwise to raise vehicle until the rising head of jack is seated in recess tightly and wheel is off the ground(about 3cm).
Emergency situation Start engine by jumper wire The battery from other vehicle may be used to start engine if vehicle battery is not charged enough to start vehicle. Any improper operation may result in battery explosion, personal injury or property damage and cause vehicle electric system failure to a certain extent.: -Do not have battery near open fire or spark -Do not have battery electrolyte cont act eye, skin, fabric or lacquer finish.
Emergency situation ground. ！Notice When engine is started by jumpers. all electrical equipments should be shut off in case other systems or parts be damaged. do not start vehicle by pushing or pulling, Thus, three way catalytic converter and other electronic parts may be damaged. Vehicle Towing If vehicle needs to be towed, cont act the nearest CHERY AUTO authorized service station. Proper lifting and towing procedure should be taken to prevent vehicle from damaging.
Emergency situation -Shut the window of towed vehicle and have for control lever in internal circulation mode to prevent leading vehicle exhaust from getting into towed vehicle. -Start slowly to avoid bumping. ！Notice When vehicle is towed by hauling cable , towed vehicle may be out of towed if wheel, transmission , turning or braking control. So vehicle should not be 99 system is damaged. M eanwhile, the following points should be taken:1、Do not remove ignition key.
Emergency situation 100
Service and Maintenance Service and Maintenance 101
Service and Maintenance 102
Service and Maintenance Engine Compartment 1. 2. 3. 4. 103 Expansion Tank Oil Filter Door Ignition Coil Brake Fluid Tank 5. 6. 7. 8. Battery Fuse Relay Block Air Filter Engine Compartment Lock 9. Oil Dipstick 10.
Service and Maintenance Service Precautions Take care when check or repair vehicle to prevent person injury or damage. Read and comply following general precautions when service vehicle: Turn off engine and let engine cool down when engine is hot. Use car stand when work under vehicle. Do work under vehicle when a jack supports vehicle. Fireworks, flame and electricity spark should be far away from battery, all parts related with fluid to avoid sudden accident.
Service and Maintenance Safety Precautions Driver Checking Items Cooling fan may op erate at any time; take care when checking to avoid possible person injury. Cooling fan is controlled by ECU and may operate suddenly. When engine is at ON position, touching operational component is dangerous because electronic controlled ignition system has more power than tradition ignition system. Perform safety service and liable vehicle operation checking.
Service and Maintenance Service and Maintenance SPECIAL CAUTION: Engine oil checking procedures Ensure engine oil at specified level and right lubrication. Inspect oil level because oil will consume when engine runs. Vehicle must be stopp ed at level surface when checking. Wait several minut es when checking oil level ensuring oil return oil pan. If engine is cold, it will take a long time for oil returning.
Service and Maintenance driving at low speed (such as frequent ON-OFF switching) Driving under dusty area. Service Interval Capacity 5,000km or 6 months (3,000 km or 3 months under poor conditions) SQR372: 2.9L (including oil filter) DA465: 3.0L (including oil filter) Bad Conditions: M ost driving distance less than 3,000km. Ambient temperature always under zero centigrade degree, and most driving distances less than 3,000 km.
Service and Maintenance General Area Cold Area Antifreeze Water 50% 60% 50% 40% Replacing Coolant Service Interval 40,000 km or every 2 y ears Capacity SQR372: 3.8L DA465 4.5L ！Notice Boiling coolant and vapor may eject under pressure, which may cause serious injury. Do not open coolant expansion tank lid when engine and water is hot. Antifreeze in engine coolant may hurt skin and eyes. Therefore necessary measures must be taken for avoiding antifreeze touch with eyes and skin.
Service and Maintenance Brake Fluid Brake fluid has high desiccation character. If over humidity is sopped up, hydraulic brake system performance may be affected. Therefore brake fluid must be replaced as specified schedul e in this manual. Fluid level in container should under MAX and over M IN scale. Low fluid level indicates brake system leakage or consumption. It must be checked and repaired at nearest CSSS in time. Open 109 fluid return cap.
Service and Maintenance If the level is too low, then fill till overflow from filler. Tighten fluid filler lid p lug. ！Notice Fluid temperature is high after driving. Wait till fluid and filler lid cool down. For circumstance protecting purpose, store used fluid or container in specified unit. Air Filter Use transmission fluid specified lubrication t able. After installing filler lid, inspect if leakage or damage exists. Service Interval Capacity Every 30000km or 12 2.
Service and Maintenance Clean carbon deposit on spark plug. Use brush to clean electrode, then raze carbon on insulation with small fill. Then blow using compressed air. Upper insulation must be cleaned. Adjust spark plug clearance (standard clearance is 0.7 mm-0.9 mm). Service Interval Every3,0000 kmor18 months, replace. Replacing Spark Plug -Clean dust on spark plug seat. -Remove high tension wire, then remove spark plug using spark plug wrench.
Service and Maintenance Windscreen Washer Fluid Use specified windscreen washer fluid. ！Notice It is dangerous if washer does not operate properly when driving. Check washer fluid level before driving. Antifreeze do harm to painting, therefore 1. do not mix antifreeze in washer fluid; 2. do not mix water with washer fluid because water may ice which will damage washer reservoir and other components of windscreen washing system. 3.
Service and Maintenance Built-in Densimeter Check if battery terminals eroded (white or red powder). For eliminating the erosion, apply soda and water solution on terminal, then solution will bubble and turns orange. After this change, purge solution with clean water and wipe off with cloth or house paper. Apply Vaseline on terminals to prevent possible erosion. Follow below precautions for better servicing battery: Install battery firmly; Keep battery top clean and dry.
Service and Maintenance Clutch Pedal Catalytic converter Over or no clutch pedal travel occurs, check and r epair it at CSSS. Do not use leaded gasoline because it do harms to catalytic converter and electronic controlled injection system. For vehicle equipped with catalytic converter, fuel filler is too small to insert leaded gasoline gun. Manual Brake Apply manual brake from release to full engage position. Count clicks to check manual br ake engage.
Service and Maintenance Wheel and tire The tires fitted by the manufacturer match the chassis and achieve op timum running comfort and security.Before exchanging other diverse type tires or wheels, consult the server guested by Chery Automobile to obtain technical support. The using of improper tires or wheel may cause an accident. ！Notice The wrong tire size will gave rise to contradiction between tires and body .
Service and Maintenance Inordinate wear is usually caused by the following causes including tire pressure in nonconformity with the provisions, no periodic tire alternation, incorrect wheel alignment, tire unbalance, emergent braking or bad driving habit. Tread wear indicator Termly inspect tread pattern depth in order to assist you in judging when to replace the tire. There is bu ilt-in tire tread wear indicator on the tire. When the tire tread is 1.
Service and Maintenance automotive dirigibility .Use standard tires with the same sizes and the same type. Don't use cold enduring tire so long as road conditions permit. Snow chain According to the road location or mode, alter tire chain regulation and inspect the chain before installation. When install chain on the tires, please necessarily carefully observe the provisions by the chain manufacturer.
Service and Maintenance 118
Service and Maintenance Inner Fuse Box 1 2 3 4 5 6 7 8 9 10 10A 30A 30A 10A 20A 20A 15A 10A 10A 15A 11 Instrument ――― Turn light Oil pump Brake lamp Radio Cigar lighter Front windscreen Back windscreen Electronic rearview mirror Room light 12 13 14 Hazard way light Central door lock Starter 10A 10A 10A 119 10A Fuse and relay of machinery room 1 Electronic control 10A module 2 Cooling fan 30A 3 ABS anti-lock 30A 4 5 6 Bugle Headlight Electronic control module Front fog light Rear fog light Left
Service and Maintenance Normal side of the instrument panel, the other is close to the accumulator in the engine room. bulb.6 keep children away from the bulb.7carefully handle with used bulb 8 moisture on hands will reduce bulb life . Importance Headlight driving beam and passing lamp -Discover engine coating and erect supporting bar. -Cut the bunch plugging components behind the bulb. -Detach the back cover. -Unfasten bulb location stanching spring and detach the bulb. -Fix new bulb.
Service and Maintenance -Fix new bulb. -Install the bulb in reversed sequence. Front turn signal lamp ！Notice Oil stain on the finger will cont aminate bulb and result in dim lamplight. Don’t touch halogen bulb with hand. Wash the bulb with clean lint-free cloth with alcohol or painter's naphtha on it. -Take down the two fixing bolts. -Cut the bunch plugging components behind the bulb. -Contra-rotate the bulb fixing holder and detach it. -Pull the lamp out from the fixed base. -Fix new bulb.
Service and Maintenance License light High-level brake light -Discover the trunk cover. -Take down the two fixing bolts and cover. -Contra-rotate the bulb fixing holder and detach it from fixing holder. -Fix new bulb. -Install the bulb in reversed sequence. -Take down the two fixing bolts. -Detach the bulb from bulb crust -Directly pull the bulb out of the fixing holder. -Push the new bulb into the fixing holder. -Install the fixing holder into the bulb crust. -Fix the two fixing bo lts.
Service and Maintenance -Push spring clip and detach the broken bulb. -Fix new bulb. -Install the bulb in reversed sequence.
Service and Maintenance 124
Automobile maintenance Automobile maintenance 125
Automobile maintenance 126
Automobile maintenance External maintenance and cleaning of automobile External lacquered surface Lacquering brings esthetic app earance and viability to automobile.
Automobile maintenance Surface coating spoilage Any fissures or deep scratches on the surface coating should be immediately patched, or the exposed metal will instantly get stained, if this continues more repair fees may be spent. Scratches could be patched with patching materials; extensive coating damages have to be patched in Chery Service Station.
Automobile maintenance Because the mobile oil in high quality is the prerequisite of ensuring engine trouble free running and durability prolonging, the special used top mobile oil specified by Chery have to apply in mobile oil addition or replacing circumstances. In respect that there are varieties of mobile oil served in the market, and the qualities of which vary a lot, it is emphasized that the mobile oil can only be chosen from the ones provided by this specification.
Automobile maintenance 130
Specifications and technical data Specifications and technical data ＜these data are provided only for reference＞ 131
Specifications and technical data 132
Specifications and technical data Dimensions Notice: Due to different types of wheel assembled, there might be some discrepancies in height data.
Specifications and technical data Engine data Performance parameters M odel SQR372 Shape Vertical, three cylinder, four cycle, water-cooling, straight type overhead camshaft, multi-spot electric control gasoline injection DA465Q---1A2/D Vertical, quadruple cylinder, four cycle, water-cooling, straight type overhead camshaft, multi-spot electric control gasoline injection 72 65.5 72 72 66.5 78 66．5 61 812 1051 1083 993 9.5:1 9.0:1 9.5:1 9.5:1 38(6000r/min) 38.
Specifications and technical data Wheel Tire Wheel rim 155/65 R13 5J*13 Notice: the above Tire----Wheel rim combination specifications is suitable for steel or aluminum alloy wheel rim, please ask Chery Service Station for advice whether other types of tire and wheel rim are fit for the vehicle.
Specifications and technical data tire inflation pressure item kPa spare tire front wheel rear wheel 155/65 R13 73H 155/65 R13 73H half load 220 220 250 full load 240 240 250 ！Notice: The tire pressure should be inspected at least once every month, which is extremely important in high speed drive. Pressure value shown in the diagram is applicable to the tires in cold conditions, after being heated the pressure of tire slightly goes up , however, it is unnecessary to lower the air pressure.
Specifications and technical data Unclassified technical characteristics SQR7080 SQR7110 SQR7111 SQR7101 Volume of drip box 35 35 35 35 Cooling system capacity including heating 3.8 4.5 4.5 4.5 Engine lubr icating system (oil change amount)---(nearly) L The capacity between t he M IN and MAX tags of dipstick-----L 2.9 3.0 3.5 3.
Specifications and technical data Data label of vehicle Formal vehicle identification number Data label of vehicle is on the cross beam of engine room. The vehicle identification number (VIN) has been printed on the cross beam under the front windshield. VIN number Engine No. The engine number is printed in the middle of front part of the steam cylinder. Engine No.
Service and Maintenance ; Service and Maintenance 139
Service and Maintenance 140
Service and Maintenance Engine Compartment 11. 12. 13. 14. 141 Expansion Tank Oil Filter Door Ignition Coil Brake Fluid Tank 15. 16. 17. 18. Battery Fuse Relay Block Air Filter Engine Compartment Lock 19. Oil Dipstick 20.
Service and Maintenance Service Precautions Take care when check or repair vehicle to prevent person injury or damage. Read and comply following general precautions when service vehicle: Turn off engine and let engine cool down when engine is hot. Use car stand when work under vehicle. Do work under vehicle when a jack supports vehicle. Fireworks, flame and electricity spark should be far away from battery, all parts related with fluid to avoid sudden accident.
Service and Maintenance Safety Precautions Driver Checking Items Cooling fan may op erate at any time; take care when checking to avoid possible person injury. Cooling fan is controlled by ECU and may operate suddenly. When engine is at ON position, touching operational component is dangerous because electronic controlled ignition system has more power than tradition ignition system. Perform safety service and liable vehicle operation checking.
Service and Maintenance Service and Maintenance SPECIAL CAUTION: Engine oil checking procedures Ensure engine oil at specified level and right lubrication. Inspect oil level because oil will consume when engine runs. Vehicle must be stopp ed at level surface when checking. Wait several minut es when checking oil level ensuring oil return oil pan. If engine is cold, it will take a long time for oil returning.
Service and Maintenance Frequent long-time idle running and/or driving at low speed (such as frequent ON-OFF switching) Driving under dusty area. Service Interval Capacity 5,000km or 6 months (2,500 km or 3 months under poor conditions) SQR372: 2.9L (including oil filter) DA465: 3.0L (including oil filter) SQR472: 3.5L(includ ing oil filter) Bad Conditions: M ost driving distance less than 3,000km. Ambient temperature always under zero centigrade degree, and most driving distances less than 3,000 km.
Service and Maintenance Cool ant Co n centrati on General Area Antifreeze 50% Water 50% Cold Area 60% 40% Replacing Coolant Service Interval 40,000 km or every 2 y ears Capacity SQR372: 3.8L DA465: 4.5L SQR472: 4.5L ！Notice Boiling coolant and vapor may eject under pressure, which may cause serious injury. Do not open coolant expansion tank lid when engine and water is hot. Antifreeze in engine coolant may hurt skin and eyes.
Service and Maintenance Brake Fluid Brake fluid has high desiccation character. If over humidity is sopped up, hydraulic brake system performance may be affected. Therefore brake fluid must be replaced as specified schedul e in this manual. Fluid level in container should under MAX and over M IN scale. Low fluid level indicates brake system leakage or consumption. It must be checked and repaired at nearest CSSS in time. Open 147 fluid return cap.
Service and Maintenance If the level is too low, then fill till overflow from filler. Tighten fluid filler lid p lug. ！Notice Fluid temperature is high after driving. Wait till fluid and filler lid cool down. For circumstance protecting purpose, store used fluid or container in specified unit. Air Filter Use transmission fluid specified lubrication t able. After installing filler lid, inspect if leakage or damage exists. Service Interval Capacity Every 30000km or 12 2.
Service and Maintenance Clean carbon deposit on spark plug. Use brush to clean electrode, then raze carbon on insulation with small fill. Then blow using compressed air. Upper insulation must be cleaned. Adjust spark plug clearance (standard clearance is 0.7 mm-0.9 mm). Service Interval Every3,0000 kmor18 months, replace. Replacing Spark Plug -Clean dust on spark plug seat. -Remove high tension wire, then remove spark plug using spark plug wrench.
Service and Maintenance Windscreen Washer Fluid Use specified windscreen washer fluid. ！Notice It is dangerous if washer does not operate properly when driving. Check washer fluid level before driving. Antifreeze do harm to painting, therefore 1. do not mix antifreeze in washer fluid; 2. do not mix water with washer fluid because water may ice which will damage washer reservoir and other components of windscreen washing system. 3.
Service and Maintenance Built-in Densimeter Check if battery terminals eroded (white or red powder). For eliminating the erosion, apply soda and water solution on terminal, then solution will bubble and turns orange. After this change, purge solution with clean water and wipe off with cloth or house paper. Apply Vaseline on terminals to prevent possible erosion. Follow below precautions for better servicing battery: Install battery firmly; Keep battery top clean and dry.
Service and Maintenance Clutch Pedal Catalytic converter Over or no clutch pedal travel occurs, check and r epair it at CSSS. Do not use leaded gasoline because it do harms to catalytic converter and electronic controlled injection system. For vehicle equipped with catalytic converter, fuel filler is too small to insert leaded gasoline gun. Manual Brake Apply manual brake from release to full engage position. Count clicks to check manual br ake engage.
Service and Maintenance Wheel and tire The tires fitted by the manufacturer match the chassis and achieve op timum running comfort and security.Before exchanging other diverse type tires or wheels, consult the server guested by Chery Automobile to obtain technical support. The using of improper tires or wheel may cause an accident. ！Notice The wrong tire size will gave rise to contradiction between tires and body .
Service and Maintenance Inordinate wear is usually caused by the following causes including tire pressure in nonconformity with the provisions, no periodic tire alternation, incorrect wheel alignment, tire unbalance, emergent braking or bad driving habit. Tread wear indicator Termly inspect tread pattern depth in order to assist you in judging when to replace the tire. There is bu ilt-in tire tread wear indicator on the tire. When the tire tread is 1.
Service and Maintenance Cold enduring tire If using cold enduring tire, 4 tires must be assembled at the same time.Driving speed should not exceed the specified highest speed of a vehicle by tire manufacturer. Using cold enduring tire must conform to tire pressure specified by the tire manufacturer. ！ NoticeUsing cold enduring tire can cause adverse impact on the security and automotive dirigibility .Use standard tires with the same sizes and the same type.
Service and Maintenance Fuse Normal side of the instrument panel, the other is close to the accumulator in the engine room. bulb.6 keep children away from the bulb.7carefully handle with used bulb 8 moisture on hands will reduce bulb life . Importance Headlight driving beam and passing lamp -Discover engine coating and erect supporting bar. -Cut the bunch plugging components behind the bulb. -Detach the back cover. -Unfasten bulb location stanching spring and detach the bulb. -Fix new bulb.
Service and Maintenance -Fix new bulb. -Install the bulb in reversed sequence. Front turn signal lamp ！Notice Oil stain on the finger will cont aminate bulb and result in dim lamplight. Don’t touch halogen bulb with hand. Wash the bulb with clean lint-free cloth with alcohol or painter's naphtha on it. -Take down the two fixing bolts. -Cut the bunch plugging components behind the bulb. -Contra-rotate the bulb fixing holder and detach it. -Pull the lamp out from the fixed base. -Fix new bulb.
Service and Maintenance -Fix the two fixing bo lts. Room light -Pry the bulb out of the room light with screwdriver. -Push spring clip and detach the broken bulb. -Fix new bulb. High-level brake light -Discover the trunk cover. -Take down the two fixing bolts and cover. -Contra-rotate the bulb fixing holder and detach it from fixing holder. -Fix new bulb. -Install the bulb in reversed sequence. License light -Install the bulb in reversed sequence -Take down the two fixing bolts.
Service and Maintenance Scheduled Maintenance Rules Complete Regulate Maintenance at Chery Authorized Service Station 159
Service and Maintenance Mileage（Km） Item 5000 15000 30000 Light, warning flasher, horn: check performance Wiper and washing system: check performance, add washer fluid if necessary Check clutch free pedal travel, adjust it if necessary Cooling system: check antifreeze level, replace if necessary Oil: Replace Oil filter: Replace Engine: check leakages (oil, antifreeze, fuel, A/C system) Engine: adjust valve clearance (only applied on SQR 7160 sedan) Battery: check electrolyte solution level, refill disti
Service and Maintenance Mileage（Km） Item Air filter: clean shell, clean filter element and replace it if necessary.
Service and Maintenance Mileage（Km） Item 5000 15000 30000 Under-body protective cover: check if damaged Seat belt: check if damaged Toe-in value and camber angle: measure, adjust if necessary Ball pin: check the clearance Engine oil sump bolt: check if loose, tighten if necessary Control arm rubber boot: check if damaged Braking hose: check if aged or damaged Braking pipe: check if damaged, eroded or leaky connection Fuel system connections: check if aged, damaged, abnormal loosening or rubbing Tire (in
Service and Maintenance Mileage（Km） Item 5000 15000 30000 Rear wheel hub bearing: check clearance and lubricating condition CO content at idle: measure and adjust if necessary Road test: check if all mechanism operates normally. Note: For manual transmission, replace gear oil in transmission case every year or 30,000 km. Replace brake fluid every 2 years or 50,000 km.
Service and Maintenance Maintenance Card At First 5,000 km Date: CHERY Service Station Seal Mileage: ___________ Use Nature: _________ Vehicle Information Vehicle ID Number: ___ Chassi s number Service Station Seal Vehicle Model Vehicle Owner： _________________ Company（Name）：_________ _____ Address：________________________ Telephone：_______________________ E-Mail：_________________________ Purchasing Date：__________________ Use Nature:________________________ Vehicle ID Number：________________ Veh
Service and Maintenance Maintenance Card At First 5,000 km Date: ____________ Mileage: ____________ Checking Items 1.Check if lubricating system, cooling system and fuel system leak 2.Replace engine oil and oil filter. 3. Check coolant level, add if necessary or adjust coolant concentration. 4. Check if driver leaks. 5. Check if steering tie rod dust boot damaged. Yes () 6. Check if constant velocity join dust boot of drive a xle damaged. 7. Check if brake fluid leaks and brake pipe/hose damaged.
Service and Maintenance Maintenance Certification Scheduled Maintenance Scheduled Maintenance Scheduled Maintenance When driving mileage reaches 10,000 km or driving for 6 months after last service, perform 5,000 km maintenance item. When driving mileage reaches 15,000 km or 6 months after last service, perform 15,000 km maintenance item. When driving mileage reaches 20,000 km or 6 months after last service, perform 5,000 km maintenance item.
Service and Maintenance Maintenance Certification Scheduled Maintenance Scheduled Maintenance Scheduled Maintenance When driving mileage reaches 25,000 km or 6 months after last service, perform 5,000 km maintenance item. When driving mileage reaches 30,000 km or 6 months after last service, perform 15,000 km maintenance item. When driving mileage reaches 35,000 km or 6 months after last service, perform 5,000 km maintenance item.
Service and Maintenance Maintenance Certification Scheduled Maintenance Scheduled Maintenance Scheduled Maintenance When driving mileage reaches 40,000 km or 6 months after last service, perform 5,000 km maintenance item. When driving mileage reaches 45,000 km or 6 months after last service, perform 15,000 km maintenance item. When driving mileage reaches 50,000 km or 6 months after last service, perform 5,000 km maintenance item.
Service and Maintenance Maintenance Certification Scheduled Maintenance Scheduled Maintenance Scheduled Maintenance When driving mileage reaches 55,000 km or 6 months after last service, perform 5,000 km maintenance item. When driving mileage reaches 60,000 km or 6 months after last service, perform 15,000 km maintenance item. When driving mileage reaches 65,000 km or 6 months after last service, perform 5,000 km maintenance item.
Service and Maintenance Maintenance Certification Scheduled Maintenance Scheduled Maintenance Scheduled Maintenance When driving mileage reaches 70,000 km or 6 months after last service, 5,000 km perform maintenance item. When driving mileage reaches 75,000 km or 6 months after last service, perform 15,000 km maintenance item. When driving mileage reaches 80,000 km or 6 months after last service, perform 5,000 km maintenance item.
Service and Maintenance Maintenance Certification Scheduled Maintenance Scheduled Maintenance Scheduled Maintenance When driving mileage reaches 85,000 km or 6 months after last service, perform 5,000 km maintenance item. Date: ________________ Mileage :______________ When driving mileage reaches 90,000 km or 6 months after last service, perform 15,000 km maintenance item. When driving mileage reaches 95,000 km or 6 months after last service, perform 5,000 km maintenance item.
Service and Maintenance COOLANT CHERY SPECIFIED OILS AND THEIR SUBSTITUTES As recommended, do use coolant according to Chery company specifications. Neither soft nor hard water can be used as coolant. ENGINE OIL If unauthorized oil is used, engine excessive wear or more serious fault may be caused. Therefore please do use specified oil. RECOMMENDED BRAND OF OTHER OIL, FLUID AND GREASE FUEL As specified, homemade premium unleaded #93 or higher-grade gasoline must be used on Chery QQ sedan.
Service and Maintenance SAFE PROTECTION SYSTEM Complete air bag system must be replaced at CASS after 10 years from use date. Replacement must be carried out at CASS. Replace air bag system at CASS as specified schedule to ensure normal operation. If air bag system was replaced before schedule (e.g. after traffic accident), fill out replacing note for later reference.
Service and Maintenance AIR BAG REPLACING NOTE ( ) DRIVER AIR BAG ( ) PASSENGER AIR BAG ( ) LEFT SIDE AIR BAG ( ) RIGHT SIDE AIR BAG ( ) AIR BAG CONTROL MODULE ( ) AIR BAG WIRING H ARNESS ( ) PRETENSION SEAT BLET ( ) OTHER PARTS 1、---------------------------2、---------------------------3、---------------------------4、---------------------------5、---------------------------6、--------------------------- DATE：-----------------------CASS SEAL HEAR 174
Service and Maintenance 175
