VT-M2M-LV VT-M2M-LV User’s Manual Chengdu Vantron Technology, Ltd. www.vantrontech.com.
VT-M2M-LV Revision History: No. Version Description 1 V1.0 First release Nov.8, 2012 2 V2.0 Upgrade PCB to Revision 2 Oct.18, 2013 3 V3.0 4 V3.1 Upgrade PCB to Revision 3, move GPS to on board, change WiFi to on board module. Add FCC and IC warning statement 2/ 21 Date Sept.28, 2014 March.
VT-M2M-LV Table of Contents 1. Foreword ...................................................................................................................................4 1.1 Copyright Notice ........................................................................................................................4 1.2 Notes ..........................................................................................................................................4 1.3 Statement ..............................
VT-M2M-LV 1. Foreword 1.1 Copyright Notice While all information contained herein have been carefully checked to assure its accuracy in technical details and printing, Vantron assumes no responsibility resulting from any error or features of this manual, or from improper uses of this manual or the software. Please contact our technical department for relevant operation solutions if there is any problem that cannot be solved according to this manual.
VT-M2M-LV 1.5 Limitation of Liability/Non-warranty For direct or indirect damage to this device or other devices of Vantron caused by failure of conforming to this manual or the safety instructions on device label, Vantron assumes neither warranty nor legal liability even if the device is still under warranty. The VT-M2M-LVshould be installed, debugged and maintained by professional people. The outside antennas are not permitted to be installed or to be changed by non-professional people.
VT-M2M-LV during transportation or placed under high temperature. Place cables properly: Do not place cables at any place with extrusion danger. Cleaning Instructions Please power off before cleaning the device. Do not use spray detergent. Clean with a damp cloth. Do not try cleaning exposed electronic components unless with a dust collector. Support for special fault: Power off and contact technical support personnel of Vantron in case of the following faults: The device is damaged.
VT-M2M-LV 2. Overview 2.1 Introduction Thank you for choosing Vantron. It is our commitment to provide our valued customers with the embedded devices equipped with the state-of-the-art technology and the best product services. Vantron’s M2M products are based on the most advanced ARM and Intel Atom processors and have low-power consumption and high integration. The products are designed for applications of M2M in industrials, medicals, financial, retail, vehicle, and transportations etc.
VT-M2M-LV 2.
VT-M2M-LV 3. M2M-LV Hardware Instructions 3.
VT-M2M-LV 3.2 Specifications Specifications CPU Processor ARM9 processor Memory On Board RAM DDR2 128MB(64Meg x 16) ROM Internal NAND 128MB (256MB or others) WLAN 3G/GPRS Module Optional 1X802.11/ b/g/n Wireless Module external antenna Optional 1x mini PCIE 3G Broad Band Module with SIM slot or GPRS module GPS Optional 1X GPS module, external antenna Zigbee Optional, or RF 2.4G Ethernet 1x10/100M-BaseT(RJ45) COM Port Alarm 1xDB9 RS232/485 1xRS232/485/422 1xCAN 2.
VT-M2M-LV 3.
VT-M2M-LV 3.
VT-M2M-LV 3.5 Interface Description 3.5.
VT-M2M-LV 3.5.
VT-M2M-LV 3.5.3 D Sub-9 RS232 or RS485 Connector Standard vertical DB-9 male connector.
VT-M2M-LV 3.5.4 RS232/422/485,CAN,ExternalIO Connector 12pins 3.
VT-M2M-LV 3.5.5 LED PWR LED: lightindicatesystem power OK(main power up);offindicate system power turn off Status LED: User can define by themself. 3.5.6SIM Card Push the small button on the left of SIM Card Holder, and install the SIM card to the holder. Then push the holder into the Slot. 3.5.7DEBUG CONN,BOX,1x3x2.0,TH,JST,VERT(JST: B3B-PH-K-S(LF)(SN)), User can show the debug message and use keyboardinput debug command.
VT-M2M-LV 3.5.8Renew button Renew button:long press this button will restore the factory setting, the long press time can be setting by user 3.5.9 Reset button Reset button:short press this button will resetthis M2M device. 3.5.10 SD/MMC socket This is standard SD card socket , user can save data on this storage. You can remove this metal cover by use screw-driver tool.
VT-M2M-LV 4. Tips Waste Disposal It is recommended to disassemble the device before abandoning it in conformity with local regulations. Please ensure that the abandoned batteries are disposed according to local regulations on waste disposal. Do not throw batteries into fire (explosive) or put in common waste canister. Products or product packages with the sign of “explosive” should not be disposed like household waste but delivered to specialized electrical ＆ electronic waste recycling/disposal center.
VT-M2M-LV FCC Warning This device complies with FCC class B Rules. Operation is subject to the Following conditions. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
VT-M2M-LV US Office: Vantron Technology, Inc. Address: 1292 Kifer Road #807, Sunnyvale, CA 94086 Tel: 510-304-7666 Email: sales@vantrontech.com China Office: Chengdu Vantron Technology, Ltd. Address: No.5 GaoPeng Road, Hi-Tech Zone, Chengdu, P.R. China 610045 Tel: 86-28-8512-3930/3931 Email: sales@vantrontech.com.
