User Manual
Table Of Contents
- Contents
- 1 Introduction to the Dolby Accessibility Solution User’s Manual
- 2 Dolby Accessibility Solution hardware components
- 3 Installing the Dolby Accessibility Solution Server
- 4 Configuring the Dolby Accessibility Solution audio
- 5 Configuring the Dolby Accessibility Solution with a Wi-Fi router
- 6 Configuring the Dolby Accessibility Solution Server with a digital cinema server
- 7 Configuring the Dolby Accessibility Solution Receiver
- 8 Setting up a Dolby Accessibility Solution Receiver for a patron
- 8.1 Enabling the talkback feature for visually impaired patrons
- 8.2 Connecting the Dolby Accessibility Solution Receiver to an auditorium
- 8.3 Selecting available resources for Brazil
- 8.4 Selecting available resources for regions other than Brazil
- 8.5 Adjusting the Dolby Accessibility Solution Receiver adjustable arm
- 9 Dolby Accessibility Solution default user accounts and passwords
- 10 Updating the Dolby Accessibility Solution system
- 10.1 Updating the Dolby Accessibility Solution Server software using secure FTP
- 10.2 Updating the Dolby Accessibility Solution Server software using USB
- 10.3 Updating the Dolby Accessibility Solution Server software using the web UI
- 10.4 Updating the Dolby Accessibility Solution Receiver software using the web UI
- 11 Dolby Accessibility Solution Server web UI
- 12 Dolby Accessibility Solution operational and technical specifications
- 13 Audio AES and adapter pinouts
- 13.1 RJ-45 Ethernet cable color codes
- 13.2 RJ-45 to 25-pin D-connector male adapter pinning
- 13.3 Pinouts for AES3 channels 1-8 output
- 13.4 Pinouts for AES3 channels 9-16 output
- 13.5 Pinout wiring for AES3 audio for Dolby cinema audio processors
- 13.6 Pinout wiring for AES3 audio for third-party cinema audio processors
- 13.7 Pinouts for the Dolby CP750 in 5.1 mode
- 13.8 Pinouts for the Dolby CP750 in 7.1 mode
- 13.9 Dolby CP850/Dolby CP950 pinouts
- 13.10 25-pin D-connector to dual RJ-45 adapter pinout
- 13.11 Pinouts for the Dolby IMS3000 AES3 auxiliary input or output port
- 13.12 Dolby DCP‑2000/Dolby DCP‑2K4 AES pinouts
- 14 Documentation revision history
- Glossary
8.1 Enabling the talkback feature for visually impaired patrons
For visually impaired patrons, you can enable the talkback feature prior to selecting the auditorium. This
feature allows the patron to hear audible prompts when interacting with the Dolby Accessibility Solution
Receiver. Note: The talkback feature is not available in Brazil when using the ASUS based receiver (part
number: CINEASSISTA-REC).
Procedure
1. From the right side of the Dolby Accessibility Solution Receiver, press the power button to turn on the
device.
2. From the Dolby Accessibility Solution Receiver home screen, tap the talkback icon at the upper right-hand
corner, next to the settings (gear) icon.
Figure 35: Tap talkback icon
Note: Headphones must be connected. If there are no headphones connected, a prompt appears
t
o connect them before proceeding. If headphones are connected, proceed to step 3.
Figure 36: Connect headphones message
3. A
er enabling the talkback feature, a prompt appears to select the auditorium number.
Se
tting up a Dolby Accessibility Solution Receiver for a patron
Dolby Accessibility Solution Userʼs Manual 46
AST.OM.005498.DRM Issue 4 14 June 2022
DRAFT