User Manual
Table Of Contents
- Contents
- 1 Introduction to the Dolby Accessibility Solution User’s Manual
- 2 Dolby Accessibility Solution hardware components
- 3 Installing the Dolby Accessibility Solution Server
- 4 Configuring the Dolby Accessibility Solution audio
- 5 Configuring the Dolby Accessibility Solution with a Wi-Fi router
- 6 Configuring the Dolby Accessibility Solution Server with a digital cinema server
- 7 Configuring the Dolby Accessibility Solution Receiver
- 8 Setting up a Dolby Accessibility Solution Receiver for a patron
- 8.1 Enabling the talkback feature for visually impaired patrons
- 8.2 Connecting the Dolby Accessibility Solution Receiver to an auditorium
- 8.3 Selecting available resources for Brazil
- 8.4 Selecting available resources for regions other than Brazil
- 8.5 Adjusting the Dolby Accessibility Solution Receiver adjustable arm
- 9 Dolby Accessibility Solution default user accounts and passwords
- 10 Updating the Dolby Accessibility Solution system
- 10.1 Updating the Dolby Accessibility Solution Server software using secure FTP
- 10.2 Updating the Dolby Accessibility Solution Server software using USB
- 10.3 Updating the Dolby Accessibility Solution Server software using the web UI
- 10.4 Updating the Dolby Accessibility Solution Receiver software using the web UI
- 11 Dolby Accessibility Solution Server web UI
- 12 Dolby Accessibility Solution operational and technical specifications
- 13 Audio AES and adapter pinouts
- 13.1 RJ-45 Ethernet cable color codes
- 13.2 RJ-45 to 25-pin D-connector male adapter pinning
- 13.3 Pinouts for AES3 channels 1-8 output
- 13.4 Pinouts for AES3 channels 9-16 output
- 13.5 Pinout wiring for AES3 audio for Dolby cinema audio processors
- 13.6 Pinout wiring for AES3 audio for third-party cinema audio processors
- 13.7 Pinouts for the Dolby CP750 in 5.1 mode
- 13.8 Pinouts for the Dolby CP750 in 7.1 mode
- 13.9 Dolby CP850/Dolby CP950 pinouts
- 13.10 25-pin D-connector to dual RJ-45 adapter pinout
- 13.11 Pinouts for the Dolby IMS3000 AES3 auxiliary input or output port
- 13.12 Dolby DCP‑2000/Dolby DCP‑2K4 AES pinouts
- 14 Documentation revision history
- Glossary
European Union
EU regulations
Dolby Laboratories hereby declares that this equipment is in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU. The complete Declaration of Conformity can be
obtained upon request.
Waste electrical and electronic equipment (WEEE)
All Dolby products, which must be recycled or handled separately, are marked with a WEEE label in
acc
ordance with the EU WEEE Directive.
Restriction of Hazardous Substances Directive (RoHS)
All Dolby products comply with the requirements of the EU RoHS Directive.
Canada
For Dolby Accessibility Solution Tablet Model VT-TAB55-RK68-DB8 only
This device complies with ISED license‐exempt Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
This class B apparatus complies with Canadian ICES‐003. CAN ICES-003(B)/NMB-003(B).
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage.
2. l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Cet appareil de classe B est conforme avec la norme ICES-003 du Canada. CAN ICES-003(B)/NMB-003(B).
This radio transmitter (ISED certification number: 11152A-TAB55) may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. Other antenna types, or
Notices
Dolby Accessibility Solution Userʼs Manual 4
AST.OM.005498.DRM Issue 4 14 June 2022
DRAFT