User Manual
Table Of Contents
- Contents
- 1 Introduction to the Dolby Accessibility Solution User’s Manual
- 2 Dolby Accessibility Solution hardware components
- 3 Installing the Dolby Accessibility Solution Server
- 4 Configuring the Dolby Accessibility Solution audio
- 5 Configuring the Dolby Accessibility Solution with a Wi-Fi router
- 6 Configuring the Dolby Accessibility Solution Server with a digital cinema server
- 7 Configuring the Dolby Accessibility Solution Receiver
- 8 Setting up a Dolby Accessibility Solution Receiver for a patron
- 8.1 Enabling the talkback feature for visually impaired patrons
- 8.2 Connecting the Dolby Accessibility Solution Receiver to an auditorium
- 8.3 Selecting available resources for Brazil
- 8.4 Selecting available resources for regions other than Brazil
- 8.5 Adjusting the Dolby Accessibility Solution Receiver adjustable arm
- 9 Dolby Accessibility Solution default user accounts and passwords
- 10 Updating the Dolby Accessibility Solution system
- 10.1 Updating the Dolby Accessibility Solution Server software using secure FTP
- 10.2 Updating the Dolby Accessibility Solution Server software using USB
- 10.3 Updating the Dolby Accessibility Solution Server software using the web UI
- 10.4 Updating the Dolby Accessibility Solution Receiver software using the web UI
- 11 Dolby Accessibility Solution Server web UI
- 12 Dolby Accessibility Solution operational and technical specifications
- 13 Audio AES and adapter pinouts
- 13.1 RJ-45 Ethernet cable color codes
- 13.2 RJ-45 to 25-pin D-connector male adapter pinning
- 13.3 Pinouts for AES3 channels 1-8 output
- 13.4 Pinouts for AES3 channels 9-16 output
- 13.5 Pinout wiring for AES3 audio for Dolby cinema audio processors
- 13.6 Pinout wiring for AES3 audio for third-party cinema audio processors
- 13.7 Pinouts for the Dolby CP750 in 5.1 mode
- 13.8 Pinouts for the Dolby CP750 in 7.1 mode
- 13.9 Dolby CP850/Dolby CP950 pinouts
- 13.10 25-pin D-connector to dual RJ-45 adapter pinout
- 13.11 Pinouts for the Dolby IMS3000 AES3 auxiliary input or output port
- 13.12 Dolby DCP‑2000/Dolby DCP‑2K4 AES pinouts
- 14 Documentation revision history
- Glossary
6.1 Configuring the Dolby Accessibility Server Ethernet 0 port
You must configure the Ethernet 0 (ETH0) port on the Dolby Accessibility Solution Server to allow it to
communicate with the digital cinema server.
About this task
You will change the IP address of the Ethernet 0 port to be within the same subnetwork as the digital cinema
server on the Management Network. If you are unsure about which IP address to use, contact your network
administrator. The Dolby Accessibility Solution Server Ethernet 0 default IP address is 192.168.100.75.
Procedure
1. From the Dolby Accessibility Solution Server desktop upper-le section, open the Firefox web browser.
Figure 22: Web browser
2. Type localhost, and then press Enter.
The Dolb
y Accessibility Solution Server web UI is displayed.
3. On the Dolby Accessibility Solution Server web UI login screen, enter the user name and password, and
then click LOGIN.
The default user name is admin, and the default password is admin.
4. When the End User License Agreement (EULA) appears, read the text, and then click AGREE.
The EULA appears during the Dolby Accessibility Solution Server initial setup and configuration process,
and also appears when you update the Dolby Accessibility Solution Server soware.
Figure 23: End User License Agreement screen
5. Aer accepting the EULA, the Setup Region screen appears. Select the correct language for your region.
Configuring the Dolb
y Accessibility Solution Server with a digital cinema server
Dolby Accessibility Solution Userʼs Manual 36
AST.OM.005498.DRM Issue 4 14 June 2022
DRAFT