User Manual

32Copyright©
J
Data
CWComm
a
will return
time is mo
r
more than
t
landing pl
a
Landin
g
Before l
a
altitude, ta
r
The pilo
t
RC, push t
h
with opera
t
If the
797, and th
After sen
APmode. In
Fixed W
the aircraft
Multi-ro
distance be
J
OUAV
Link:
If t
h
a
nder. If th
e
to waypoi
n
r
e than tim
e
t
imeout lan
d
a
n and land
a
g
a
nding, the
r
get waypoi
t
should co
n
h
e throttle t
t
or of GCS.
wind direct
hen rotate th
nding “Land
n addition, d
Wing Status
is always g
otor Status
etween aircr
h
e data li
n
e
time afte
r
n
t 0. If the
a
e
out return
d
ing settin
g
a
utomatica
l
operator sh
nt, rotors p
o
n
firm the
R
o middle.
A
tions has ch
he landing p
ding” comm
data and co
:
If the altitu
going around
:
While the
raft and land
n
k is disco
r
disconnec
t
a
ircraft is
f
setting, it
w
g
and it’s fa
r
l
ly.
ould confir
m
o
wer.
R
C is auto
m
A
nd confir
m
hanged, pre
plan.
mand, the op
nditions nee
ude of aircra
d, increase t
aircraft is h
ding point i
nnected, t
h
t
ed data li
n
f
ar from th
e
w
ill return t
o
r
from the l
a
m
the statu
s
m
ode, and
k
m
the contr
o
ess shift and
perator shou
ed to pay at
aft is lower
the Lateral
hovering bu
s no more t
h
e RX wi
l
n
k is more t
h
e
take off p
o
o
waypoint
a
nding poi
n
s
, such as l
a
k
eep the thr
o
l status is
R
d left button
uld pay atten
ttention, as
r than Landi
Deviation.
ut not desce
than 10m. a
l
l stop inc
r
h
an time o
u
o
int more t
h
0. If the d
a
n
t less than
2
a
nding com
m
o
ttle mini
m
R
C Normal
n of mouse t
ntion to alti
follows:
ing Height,
ending, it w
and it will fo
r
easing w
h
u
t limit set
t
h
an 1km a
n
a
ta link is
d
2
km, it wil
l
m
and, AP
m
m
um, then s
w
and throttl
e
to choose th
tude, rotors
it will force
will land afte
orce landing
h
ich on th
e
t
ing, aircra
f
n
d the flig
h
d
isconnecte
d
l
trace to th
e
m
ode,
w
itch on th
e
e
is about 5
0
he waypoin
s power and
e landing. I
er 20s if the
g after 1min
e
f
t
h
t
d
e
e
0
%
t
d
f
e
n
if the distance is more than 10m. Either you can send “Landing” command to land it.
Touch Ground:
After touching ground, keep the throttle minimum, and switch the RC to ATT
mode. If the propeller keeps running and not stop, send “Abort” to stop it.