ES340 Chassis User Manual Chenbro ES340 Chassis User Manual www.chenbro.
ES340 Chassis User Manual Copyright Copyright © 2007 Chenbro Micom Co., Ltd.. All rights reserved. Unless otherwise indicated, all materials in this manual are copyrighted by Chenbro Micom Co., Ltd.. All rights reserved. No part of this manual, either text or image may be used for any purpose other than internal use within purchasing company.
ES340 Chassis User Manual Content Packing list ……………………………………….…………………………4 Features …………………………………………..……………………………6 Technical specification ………………………..………………………........6 Opening the chassis …………………………..…………………………….7 Installing devices ……………………………..……………………………10 Installing Mini-ITX M/B …...………………...……………………….........10 Installing Slim-CDROM ……...……………..……………………………10 Installing 3.5” Hot-swap hard drive …...…...……………………………..11 Installing card reader ……..……………………………………………….12 Installing heatsink ………………………..
ES340 Chassis User Manual Packing List z ES340 chassis SATA2/SAS Shield USB 2.0 SATA 7-pin Cable, Backplane (2) Cables (1) 260mm (2) Power Distribution Hot-swap HDD Slim-CDROM SATA 7-pin Cable, Board (1) Carrier (4) Carrier (1) 360mm (2) Split Power Cable, Split Power Cable, Split Power Cable, Type-II (1) Type-II (1) Type-II (1) 70mm fans (2) Intrusion Switch (1) z Power adaptor kit 120W Power Adaptor (1) www.chenbro.
ES340 Chassis User Manual z Accessory pack Screw Pack for Slim ODD Adaptor MB (1) (1) Power Cable, Big 4P Screw Pack for PCI Add-on Card to Small 4P (1) HDD (1) Cable Tie (1) Front Bezel Key (1) Bracket (1) Optional Kits There are optional kits for different purposes, please contact our sales for more information and availability. PCI 32-bit Riser Card (1) www.chenbro.
ES340 Chassis User Manual Features z Silver-gray powder coating combined with simple lining z Ideal for high storage capacity (Hot-swap HDDs) with RAID-5 functionality z Available for multi-media platform z 9.
ES340 Chassis User Manual Opening the Chassis Overview Side Panel w/Venting Slim CD-ROM Carrier Main Cable Through Hole w/Rubber pad Front Bezel (w/Key Lock) Intrusion Switch USB & Front Control Cables Motherboard Cage Front Card Reader (Option) -- Support MS,SD,Mini-SD,MMC Slim CD-ROM Cover USB 2.0 ports x2 Front Control Display: 4x 3.
ES340 Chassis User Manual To open the chassis for assembly of internal parts, users need to: z Remove the side panel z Remove the front bezel To remove the side panel: 1 2 ■ Release the side panel thumb screw on the rear ■ Push and slide the side panel toward rear to open the chassis To remove the front bezel: 1 2 ■ Lift up the latch along the side to detach the bezel ■ Detach the bezel from Slim ODD side gently 3 4 ■ Angle the latch until it is 15 degree away from the ■ gently pull the be
ES340 Chassis User Manual To remove the M/B cage: 1 2 ■ Release the secure screws on the M/B cage ■ Release the two screws around the rear fans 3 4 ■ Remove the motherboard cage ■ Disconnect the extension fan cables 5 6 ■ Detach the motherboard cage with System Cables (SATA, Power, Fan cables) through the cable routing hole ■ Finish detaching the M/B cage and make sure all the www.chenbro.
ES340 Chassis User Manual Installing Devices: There are other optional devices for ES340, including: z Mini-ITX or Mini-DTX z z z z Slim Optical Drive Standard SATA2 Hard Drive 4-in-1 Mini Card Reader (Optional) Dedicated Universal Heatsink for AMD/Intel CPU Installing Mini-ITX or Mini-DTX M/B: 1 2 ■ Attach the motherboard I/O gasket (provided by M/B) ■ Attach screws to fix the motherboard. Installing Slim Optical Drive: Before install the slim CD-ROM, the front bezel must be removed.
ES340 Chassis User Manual 3 4 ■ Slide in the assembled CD-ROM into the chassis ■ Make sure the holder latch is secured when fully seated Installing 3.5” SATA2 Hard Drive: 1 2 ■ Remove the HDD Carrier from the chassis and place the SATA2 HDD into it. ■ Attach the HDD screws on both sides 3 4 ■ Slide in the assembled HDD into the chassis, suggest ■ Make sure the carrier is fully seated install by the ID definition on the front panel (No need to remove the front bezel) www.chenbro.
ES340 Chassis User Manual Installing Card Reader (optional): 1 2 ■ Detached the front screw of Card Reader holder ■ Pull out the Card Reader holder 3 4 ■ Remove the seal on the holder and make sure the sockets is right to the opening ■ Attach screws to fix the Card Reader 5 6 ■ Connect the short end of USB split cable to Card Reader with ■ Install the assembled Card Reader back to the chassis with attach screw www.chenbro.
ES340 Chassis User Manual Installing Dedicated AMD/Intel Heatsink (optional): The Chenbro heatsink for ES340 is designed specifically to support Intel and AMD desktop LV (Low Voltage) CPU in universally. Note the CPU power rating should not over 65W as maximum. 1 2 ■ Attach the heatsink retainer on to M/B before install M/B into the chassis (Note: AMD M/B are preinstalled it) ■ After installing CPU with heat spread, gently clip the heatsink with metal clipper in one end.
ES340 Chassis User Manual Installing Riser Card (optional): 1 2 ■ The PCI card mounting bracket must be detach and use special one for mounting, (Ex. PCI RAID card) ■ Connect the cables before install. 3 4 ■ Gently install the PCI card with riser into the slot. (Please pay attention to the cable arrangement) ■ Attach screws on the rear side to secure the PCI card Installing 2.5” HDD: 1 2 ■ Place the 2.5” HDD underneath the Slim ODD ■ Fix the 2.
ES340 Chassis User Manual Connecting Devices: ES340 is pre-installed with several cables inside as factory default, which includes: z SATA2 cable for Hot-swap hard drive z Power cable for M/B z Front panel I/O cables USB 2.
ES340 Chassis User Manual To connect front panel I/O and LEDs: a. USB 2.0 cable connection 1 ■ Front USB cable should be connected to on-board USB header properly depends on different M/B. b. Front display cable connection 1 2 ■ The display fan-out cable with different connection for: Power on, HDD, LAN, FAIL and the front switch ■ Connect to the M/B according to the M/B pin header definition properly. c.
ES340 Chassis User Manual d. Slim ODD cable connection (optional) 1 2 ■ Use power split cable in accessory pack for conversion ■ Use either standard IDE cable from 3rd party M/B, or of DC harness, small 4P is connected to the Slim ODD adaptor board use optional cable from Chenbro to connect to the Slim ODD adaptor board e. Cable management 1 2 ■ Due to limited space inside the chassis, make sure all ■ Tie up the cable so the cables are fixed in certain space.
ES340 Chassis User Manual Power Adaptor and Backplane Power Adaptor Specification: For electrical specification: Input Characteristics Output Characteristics Item Spec Item Spec Rated Input Voltage 100V / 240V Output Raged Voltage 19V Input Voltage Range 90VAC to 264VAC Output Current 6.32A Input Frequency Range 47Hz to 63Hz Output Voltage Setting 18.05V~19.
ES340 Chassis User Manual Power Distribution Board: The PDB (Power Distribution Board) inside the ES340 is a specific DC to DC adaptor, which only provides the converting from DC19V to multiple voltages include +5V, +3.3V and +12V for all the devices and boards usage scale up to 180W Power Adaptor. As the warning message on the back side, any improper 3rd party Power Adaptor may cause damage to the PDB or internal components.
ES340 Chassis User Manual 2-port SATA2 Backplane Introduction: ES340 is integrated with two SATA2 backplanes to support four 3.5” HDD hot-swap feature. With dedicate backplane bracket assembled, users can directly attach the HDD on the tray and plug into the HDD slot.
ES340 Chassis User Manual (1) [CN12/CN22] : Connect “22+7”pin SAS connector to HDD (2) [CN13/CN23] : SATA connector to Host (3) [FAN1 / FAN2 / FAN3 / FAN4 / FAN5] : Fan connectors (4) [SW1] : Function Setting Switch (5) [CN3] : Power Connectors (6) [CN1] : LED Header (7) [CN2] : Micro-P Programming Interface (Reserved) Pin Assignment [CN1] Pin Def. Pin Def.
