User manual

30
29
installation (continued)
oven dimensions
oven height (A)
Underbench oven 595mm
Separate grill underbench oven 725mm
Separate grill walloven 888mm
Duo oven 888mm
Double oven 1083mm
All built-in ovens are 595mm wide
cabinet construction for your
appliance
For the best integration within a kitchen, install this appliance
inastandard600mmwidecupboardthatgivesausht
with the surrounding cupboard fronts (figure A)�
Arecessof20mmisideal.Itcanalsobeinstalledusinga
proud fit with the surrounding cupboard (figure B)�
NOTE: Your appliance must be mounted on a flat surface for
the full width and depth of the product.
16mm cleat
Figure A - Flush fit (top view)
Figure B - Proud fit (top view)
Cupboard
door
Cupboard
door
Infill panel
Cupboard front
20mm
600mm
565mm
16mm cleat
Figure A - Flush fit (top view)
Figure B - Proud fit (top view)
Cupboard
door
Cupboard
door
Infill panel
Cupboard front
20mm
600mm
565mm
A
15mm
545mm 9mm min.
clearance
28
installation
warning
IMPORTANT: This appliance must be properly
earthed�
• Donotlifttheappliancebythedoorhandles.
• Preparethecupboardopeningtomatchyourappliance
measurements� (See diagrams on following pages)�
• Slideapplianceintothecupboard,ensuringthatthe
supply cable (where fitted) does not kink�
• Topreventtipping,usethescrewssuppliedtosecure
your oven into the cupboard� Use just 2 screws for single
cavity ovens and 4 screws for dual cavity� Remove the
bottom door in dual cavity ovens to provide access to the
bottom 2 screwing points (see illustrations on page 30
and 32)�
• Forappliancesttedwithaexiblesupplycord,ifthe
cord is damaged, it must be replaced by the manufacturer
or its service agent or similarly qualified person in order
to avoid a hazard� The plug must be accessible after
installation�
• Wheretheapplianceisbuiltintoacabinet,thecabinet
material must be capable of withstanding 70°C�
Installationintolowtemperaturetolerantcabinetry(e.g.
vinyl coated) may result in deterioration of the low
temperature coating by discolouring or bubbling�
• Iftheapplianceisinstalledadjacenttovinyl-wrapped
surfaces, use an installation kit available from the vinyl-
wrap supplier�
• ElectroluxHomeProductscannotacceptresponsibility
for damage caused by installation into low temperature
tolerant cabinets�
• Afterinstallation,testandensurethattheappliance
operates correctly before handing it over to the customer�
caution
To avoid any potential hazard, you must follow our
instructions below when you install your appliance� Failure to
install the appliance correctly could invalidate any warranty
or liability claims and lead to prosecution�
warning
USE AN AUTHORISED PERSON
As stated in the local municipal building codes and other
relevant statutory regulations�
• WiringconnectionsmustbeinaccordancewithAS/NZS
3000 Wiring Rules and any particular conditions of the
local authority�
• Refertodataplateforratinginformationandcircuit
diagram� The data plate is positioned behind the bottom
of the oven door� The circuit diagram is positioned on the
top panel of the appliance�
• Anallpoledisconnectfunctionalswitchshouldbe
provided near the appliance in an accessible position�
RefertoAS/NZS3000clause4.3.11
• Wiringshouldbeprotectedagainstmechanicalfailure.
RefertoAS/NZS3000clause3.9
• Ameansofdisconnectionwithacontactseparationofat
least 3mm must be supplied in the fixed wiring�
• Togainaccesstothemainsconnectionterminals,remove
the rear access cover by unscrewing the 2 screws�
• Ifthesupplycordisdamaged,itmustbereplacedby
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard�
• Forappliancesttedwithasupplyexiblecord,ifthe
cord is damaged, it must be replaced by the manufacturer
or its service agent or similarly qualified person in order
to avoid a hazard� The plug must be accessible after
installation�
Multi-phase
Where connection is made to a multi-phase 240V supply,
the bridge piece should be removed from between the active
connections�