Torque Test Stands Series TS MODELS TST / TSTH & TSTM / TSTMH User’s Guide
Series TS Torque Measurement Test Stands Thank you! Thank you for purchasing a Mark-10 Series TS Torque Measurement Test Stand. We are confident that you will get many years of great service from this product. Mark-10 test stands are ruggedly built for many years of service in laboratory and industrial environments. This User’s Guide provides unpacking, setup, and operator instructions for each model in the TS Torque Measurement Test Stand Series. Dimensions and specifications are also provided.
User’s Guide UNPACKING AND SETTING UP 1. Carefully unpack the test stand from the box and inspect for any damage. Check the contents to ensure that you have received a test stand complete with all accessories – see the list of included items below. 2. Remove the foam from the middle portion of the test stand and remove the plywood caps by unscrewing the pair of screws at each end. For the TST and TSTM models, install the base with four 5/16-18 x 1” screws and the top cap with two 1/4-20 x 5/8” screws.
Series TS Torque Measurement Test Stands TST / TSTH SETUP AND OPERATION 1. Mount the test stand to a firm, flat, and level working surface for maximum safety and accuracy using four 5/16 screws (not included). Use the included mounting hole drill template to accurately drill the holes. Testing can take place without securing the test stand in such a manner, however, it is strongly recommended that the stand be secured, especially for high torque tests. 2.
User’s Guide TST / TSTH DIMENSIONS in [mm] TST TRAVEL STOP 15 [381] MAX TRAVEL STOP 31.6 [802] 18 [457] MAX SLIDER LEVER 4.1 [104] #10-32 UNC-2B X 0.50 [12.7] DEEP X16 HAND WHEEL 7.9 [201] 9.4 [239] TSTH #10-32 UNC-2B X 0.50 [12.7] DEEP X 16 19 [483] MAX SLIDER LEVER 16 [406] MAX 4.1 [104] 10.0 [254] 5.00 [127.0] 6.
Series TS Torque Measurement Test Stands TSTM / TSTMH SAFETY TIPS Wear eye and face protection when testing. Although the TSTM / TSTMH has relatively slow moving mechanisms, be aware of the dangers posed by potential energies that can accumulate in the sample during testing. Keep away from the moving parts of the test stand. Never operate the test stand if there is any visible damage to the power cord or the control unit.
User’s Guide TSTM / TSTMH 2. Install an appropriate sensor onto the slider bracket. An indicator bracket that mounts onto the test stand column is available separately. 3. Install any required attachments, grips, adapters, and other items necessary for your test sample. Ensure that these items are set up in a secure and safe manner. 4.
Series TS Torque Measurement Test Stands TSTM / TSTMH Using the Control Unit CCW Press and hold for counter-clockwise motion, release button to stop. Located on the face of the Control Unit. CW Press and hold for clockwise motion, release button to stop. Located on the face of the Control Unit. SPEED CONTROL DIAL Adjust speed by turning the dial 0.3 – 8.6 RPM (4 – 52º/s). Located on the face of the Control Unit.
User’s Guide TSTM / TSTMH DIMENSIONS in [mm] TSTM 7.50 [190.5] 5/16-18 UNC-2B X 0.60 DEEP X4 31.6 [802] 13 [330] MAX 7.30 [185.4] BASE PLATE BOTTOM VIEW 4.1 [104] Ø0.188 [4.78] X 0.35 DEEP PILOT HOLE 0.50 [12.7] TYP Ø3.00 [76.2] 0.50 [12.7] TYP TORQUE PLATE TOP VIEW 7.9 [201] 9.4 [239] TSTMH #10-32 UNC-2B X 0.50 [12.7] DEEP X 16 SLIDER LEVER 19 [483] MAX 16 [406] MAX MANUAL ADJUSTMENT KNOB MOTOR DRIVE 4.1 [104] 10.0 [254] 5.00 [127.0] 6.
