User Manual

ManualsBrandsCheckline ManualsMeasuring instrumentsP2

ELECTROMATIC Equipment Co., Inc.

-16-

NOTES

ELECTROMATIC Equipment Co., Inc.

-1-

TABLE OF CONTENTS

1.0 Introduction …………………………………………………………….. 2

1.1 Quality information

1.2 Application

1.3 First setting into operation

2.0 Measuring procedure …………………………………………………. 3

3.0 How to choose type of product ………………………………………. 4

4.0 Verification and correction of switch position ………………………. 5

5.0 Measuring method ……………………………………………………. 5

6.0 Most common reasons for measuring errors ………………………. 6

7.0 Measuring principle …………………………………………………… 7

8.0 Exclusion of liability …………………………………………………… 8

9.0 Care regulations ………………………………………………………. 8

10.0 ISO-approved examination of the instrument ……………………… 9

11.0 Technical data ………………………………………………………… 13

12.0 Warranty ………………………………………………………………. 14

Summary of content (9 pages)

PAGE 1
NOTES TABLE OF CONTENTS 1.0 Introduction 1.1 1.2 1.3 …………………………………………………………….. 2 Quality information Application First setting into operation 2.0 Measuring procedure …………………………………………………. 3.0 How to choose type of product 4.0 Verification and correction of switch position 5.0 Measuring method 6.0 Most common reasons for measuring errors 7.0 ………………………………………. 3 4 ………………………. 5 ……………………………………………………. 5 ………………………. 6 Measuring principle …………………………………………………… 7 8.
PAGE 2
1.0 INTRODUCTION NOTES 1.1 Quality information We would like to inform you that your measuring device corresponds to the CE norms EN50081 and EN50082. The function of your instrument has been examined and calibrated before delivery. 1.2 Application P2: P4: LM5: Mainly for very strong paper, packing paper, cardboard Mainly for paper used for offset printing Mainly for leather 1.3 First setting into operation Your measuring device should be supplied with a battery by the manufacturer.
PAGE 3
12.0 WARRANTY 2.0 ELECTROMATIC Equip’t Co., Inc. warrants to the original purchaser that this product is of merchantable quality and confirms in kind and quality with the descriptions and specifications thereof. Product failure or malfunction arising out of any defect in workmanship or material in the product existing at the time of delivery thereof which manifests itself within one year from the sale of such product, shall be remedied by repair or replacement of such product, at ELECTROMATIC Equip’t Co.
PAGE 4
3.0 HOW TO CHOOSE TYPE OF PRODUCT Since there is no unified manufacturing process of the measuring products the adjustment of the switch can not be standardized. But there is always the possibility of having your device calibrated by Checkline Europe. In this case we need a pile of your product (2 cm thick) size A4 in a plastic wrapping that is as tight as possible. You can classify your products by means of a comparison measurement applying methods appropriate for verification according to DIN20287.
PAGE 5
Copy this table and fill in the displayed values – without temperature correction – and the ambient temperature. Enclose a copy of the data if the instrument should be adjusted again by the factory.
PAGE 6
.0 MOST COMMON REASONS FOR MEASURING ERRORS  Product temperature beyond ambient conditions: The temperature of the measuring device and of the product should be nearly equal.  Wrong switch position  Uneven pressing  Wrong application on rolls Press your measuring device lengthwise to the longitudinal axis of the product roll, otherwise the bearing area of the sensor is too small.
PAGE 7
This example has only been calculated for P2, but the temperature correction can be calculated for both P4 and LM5. Your measuring device is adjusted to a temperature of 28°C. The display of P2 with switch position S1 on proof plane PP2 is 6.1%. Tcf: Temperature correction factor corresponds to 0.04% (S1) moisture of paper per 1°C.
PAGE 8
.0 EXCLUSION OF LIABILITY 10.0 The producer can not be made liable for any measuring errors and the damage that might result from it. This measuring principle is a quick measuring procedure which can be influenced by product and user-specific margin conditions. Therefore it is recommended to carry out a plausibility check of the measured values. In every measuring device there is a serial number and a seal of warranty. If this seal is broken no warranty claims will be accepted.
PAGE 9
P2, P4, LM5 PAPER MOISTURE METER OPERATING INSTRUCTIONS