Snapshot Outdoor Use Sound Activated There are 2 different versions of this product. The first version has a red LED display, while the second version has a blue LCD display. Both versions of the user manual are available for download on the Chauvet® website. Please be sure that you are working with the appropriate version of the manual. DMX Master/Slave Auto-ranging 100~240 VAC, 50/60 Hz Circuit Breaker User Serviceable Duty Cycle User Manual 3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
TABLE OF CONTENTS 1. BEFORE YOU BEGIN ....................................................................................................................................................... 3 WHAT IS INCLUDED ................................................................................................................................................................................ 3 UNPACKING INSTRUCTIONS ....................................................................................................
1. BEFORE YOU BEGIN What is included 1 x Pro-D6 1 x Warranty Card 1 x User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials.
Safety Instructions Please read these instructions carefully, which include important information about the installation, usage and maintenance of this product. Caution! Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to rain or moisture.
Product Overview Line A (Channels 1-3) Line B (Channels 4-6) Line B Circuit Breaker DMX Out Line A Circuit Breaker DMX In Line B Power Switch Line B Power Cord Line A Power Switch Line A Power Cord 20 A Plug Connection Pro-D6 User Manual 5 8/12/2010 12:19 PM
3. SETUP Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller, or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. Important: Fixtures on a serial data link must be daisy chained in one single line.
Cable Connectors Cabling must have a male XLR connector on one end and a female XLR connector on the other end. COMMON INPUT CAUTION! 1 3 2 1 3 2 DMX + DMX 120 ohm, 1/4w resistor between pin 2 (DMX -) and pin 3 (DMX +) of the last fixture. 1 3 2 DMX connector configuration - OUTPUT To avoid signal transmission problems and interference, it is always advisable to use a DMX signal terminator. Do not allow contact between the common wire and the fixture’s chassis ground.
Mounting Orientation This fixture may be mounted in any position provided there is adequate room for ventilation. Rigging Hanging Clamp It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs.
Menu Functions MAIN FUNCTION Dmx fail SUB-FUNCTION Hold Prog1-12 Blackout Block Dmx address Single ALL Preheat Single ALL Max level Single ALL SELECTION INSTRUCTION Speed time Value=00.2s-20.
General Troubleshooting Applies to Symptom Solution(s) Lights Foggers & Snow Controllers Dimmers & Chaser Auto shut off Check fan thermal switch reset Breaker/Fuse keeps blowing Check total load placed on device Chase is too slow Check users manual for speed adjustment Device has no power Check for power on Mains. Check device’s fuse.
5. APPENDIX DMX Primer There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A fixture capable of receiving DMX-512 will require one or more sequential channels. The user must assign a starting address on the fixture to indicate the first channel reserved in the controller. There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required. Choosing a start address should be planned in advance.
Returns Procedure Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued. Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #). Products returned without an RMA # will be refused. Call CHAUVET and request an RMA # before shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return.
