Assembling & Installation Instructions

ManualsBrandsCharlton Home ManualsLightingPatriot Outdoor 3-Light 87'' Lamp Post

ASSEMBLING

ASSEMBLING &

& INSTALLATION

INSTALLATION

INSTALLATION INSTRUCTIONS

INSTRUCTIONS

INSTRUCTIONS FOR

FOR

FOR PRODUCT

PRODUCT

OUTDOOR

OUTDOOR POST

POST

POST LIGHT

LIGHT

LIGHT FIXTURE

FIXTURE

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .

ASSEMBLING

ASSEMBLING THE

THE

THE FIXTURE

FIXTURE

FIXTURE (

(

( Fig.

Fig.

Fig. 1

1 )

)

) .

* Shut

Shut

Shut off

off

off the

the

the power

power

power at

at the

the

the circuit

circuit

circuit breaker

breaker

breaker and

and

and remove

remove

remove old

old

old fixture

fixture

fixture ,

including

including the

the

the old

old

old small

small

small hardware.

hardware.

1. Carefully unpack new fixture and lay all the parts on a clear

surface.Take care not to lose any small parts necessary for

installation.

2. Install the light bulbs in accordance with the fixture specifications

NOTE:

NOTE: DO

DO NOT

NOT

NOT EXCEED

EXCEED

EXCEED THE

THE

THE SPECIFIED

SPECIFIED

SPECIFIED WATTAGE!

WATTAGE!

3. Raise the glass(C) into the glass frame of the fixture body(D) and

lock it securely with the clip.

4. Attach the cover(A) onto the fixture body(D), lock it securely with

hex nut ( B ) .

5. Screw the pole(E),(F) together tightly. Follow

Follow wiring

wiring

wiring instructions

instructions

carefully

carefully (see

(see

(see fig.2).

fig.2).

6. Put the pole(H) onto the concrete base using the mounting knob(I).

A. The depth of the base will depend on local soil conditions and

frost line.The diameter of the base should be 305mm in order

to hold the anchor bolts on the plate.

B. Take the three bolts(K) and run a hex nut(L) fully down each

part of the threaded section. Insert the bolt(K) to the

template(J) and secure with the second hex nuts.

C. Mix and pour the concrete into the former until it reaches the

top.Push the assembly into concrete until the plate are 0.25

inches above the concrete .Leaving 2.5 inches of the thread

above the concrete.

D. It is important to level the template before the concrete sets.

7. Install the fixture together with the pole(E),(F) onto the

pole(H),secure them using the machine screws(G).

CONNECTING

CONNECTING THE

THE

THE WIRES

WIRES

WIRES (

(

( Fig.

Fig.

Fig. 2

2 )

)

* Feed

Feed

Feed the

the

the fixture

fixture

fixture wires

wires

wires through

through

through the

the

the pole

pole

pole (

(

( E

E )

)

) ,(F)

,(F)

,(F) .

1. Take the black wire (hot) from the outlet box and the black wire of

fixture and twist bare ends together. Twist wire connector onto end

of wire until snug.

2. Repeat same process with white wire(neutral) from outlet box and

white wire of fixtur e . NOTE: Twist wires together in the same

direction you twist the wire connector onto wires.

3. If your outlet box has a grounding wire (green or bare copper),

attach this wire and the bare copper wire from the fixture together

as step 1.If junction box has no ground wire, attach the bare copper

fixture wire to the green ground screw i n the bottom of the

pole(H).

4. Tuck the wire connections neatly into the pole.Take the fixture

body(D) mount onto the pole(E) .

Your

installation

installation is

is now

now

now complete.

complete.

complete. Return

Return

Return power

power

power to

to the

the

junction

junction box

box

box and

and

and test

test

test the

the

the fixture.

fixture.

Fig.

Fig. 1

Fig.

Fig. 2

White or

HOUSE

Black

WIRES

(Hot)

Smooth

FIXTURE

WIRES

Black or

Ribbed

WIRES

FIXTURE

Bare Copper(Ground)

FIXTURE

WIRES

Copper

(Ground)

HOUSE

(Neutral)

WIRES

White

Bare

Green or

WIRES

HOUSE

Listed