Use and Care Guide
Handle
Down
Locking Mechanism
Handle
Up
WARNING
Parts, Piezas, Pièces
6-5388
Hose Assembly
Ensamblaje de la manguera
Assemblage de boyau
2. Filter
e lter helps prevent clogging while spraying. It is located on the
end of the white tube inside your sprayer tank.To clean lter, remove
the hose from the tank and lift out the outlet tube. Make sure the lter
is positioned at the bottom of the tank as pictured.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overll to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
7. Care, Storage and Maintenance
Congratulations!
You have just purchased a quality Chapin product. Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store. Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin. Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda; llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin. Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com Questions ? Ne retournez pas au magasin. Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
014917 (A) R0417
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
6-8242
Extension wand, Vara de extensión, Lance de rallonge
For safety lock-o feature (no-spraying), pull up on handle and move red locking mechanism into lock-o
position as shown in g. 8a. To disengage, push down on handle and return red locking mechanismto
neutral position as in g. 8c. For lock-on feature (continuous spraying), push down on handle and move red
locking mechanism into lock-on position as shown in g. 8b. To disengage, push down on handle and return
red locking mechanism to neutral position as shown in g. 8c.
8. Fatigue-free spraying
Filter
8b
8a
LOCK-OFF POSITION LOCK-ON POSITION NEUTRAL POSITION
8c
6-8243
O-ring Kit
Kit de junta tórica
Trousse de joint torique
Elbow O-ring Hose Washer
Nozzle Gasket Wand O-ring
Filter
2a
5. Pressurizing and Spraying
5A
5C
5B
Sk-1154-1
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious eye
or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized
sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or leave solution
in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying.
Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or body over top of tank
when pumping or loosening pump to prevent ejecting pump assembly and/or solution from striking and injuring you.
Never pressurize sprayer by any means other than the original pump. Do not attempt to modify this sprayer. Replace
parts only with manufacturer’s original parts. Never spray ammable, caustic, acidic, chlorine, bleach or other
corrosive solutions or heat, pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s
instructions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling, Pressurizing and
Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly
rinsed with water after each use.
2) Do: Open shut-o and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
1. Assembly of Shut-off, Extension Wand and Nozzle
1) Screw nozzle assembly onto threaded end of the extension wand securely.
2) Insert unthreaded end of extension into shut-o assembly as shown and tighten retaining nut securely.
Shut-o Assembly
Retaining Nut
Extension Wand
Nozzle Assembly
1a
6-8148
Nozzle Kit
Tobera
Buse
6-8241
Shut-o Assembly
Unidad de cierre
Assemblage d’arrêt
6. To Release Pressure
1) Your sprayer is equipped with a pressure relief/release
valve (Fig. 6A). To release pressure lift and hold the cap
until air is completely exhausted, OR, turn the valve slowly
counterclockwise until you hear air escaping and wait air is
completely exhausted (Fig. 6B).
2) Do: Stay away from the sprayer until all air has escaped.
6A 6B
6-8093
Poly Adjustable
Nozzle
Tobera
Buse
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose
before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for
signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could
result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace.
Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and
inspect for leaks).
5) Do: Direct shut-o away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with
Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and ttings for rust, corrosion and pitting. If any of these
conditions are found, replace aected part with original manufacturer’s part before using.
9. Replacing Hose to Tank
Make sure black adapter
is attached to outlet tube
adapter.
9A
No gap
9C 9D9B
Press hose over adapter. Make sure worm gear
clamp is below black
adapter .
Tighten clamp fully.
Black
Adapter
WARNING:
is product contains chemicals, including lead, known to the state of California
to cause birth defects and other reproductive harm. Wash hands after handling.
Do: Turn handle clockwise to
tighten. Push handle down,
turn 1/4 turn counterclock-
wise to release.
Do: Pump until you
feel resistance.
Do: Push handle, down, turn
1/4 turn clockwise to lock. Begin
spraying. Re-pump sprayer as
required to maintain spray force.
5A
5C
5B
6-8244
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y
juntas (no incluido)
Kit de pièces de réparation, joints et garniture
d’étanchéité (non inclus)
Nozzle Assembly
Figure 1
Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5). Unscrew the retaining nut
(2). Push the nozzle body (3) with the nozzle gasket (4) out of the retaining nut (2). To reinstall the nozzle, reverse the above instructions.
Figure 2
Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut. To reinstall the nozzle, reverse
the above instructions.
1. Poly
Nozzle Cap
2. Retaining
Nut
3. Nozzle
Body
4. Nozzle
Gasket
5. Elbow
Fan Nozzle
Tip
Retaining
Nut
Nozzle
Gasket
Elbow
6-8096
Flat Fan
Nozzle
Tobera
Buse