Use and Care Guide

WARNING
Parts, Piezas, Pièces
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-1925
5. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overll to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
6. Pressurizing and Spraying
8. Care, Storage and Maintenance
2-1091-101 (A) R0419
7. To Release Pressure
Do: With valve facing away from you, lift and hold the cap until air is completely
exhausted, OR, turn the valve slowly counterclockwise until you hear air escaping and
wait air is completely exhausted.
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
7A
9. Fatigue-Free Spraying
For constant spraying, push down on shut-o handle and move grey locking
mechanism away from you. To release, squeeze handle and move the grey locking
mechanism back towards you. ( Not all models are provided with this feature).
9A
Locking
mechanism
Congratulations!
You have just purchased a quality Chapin product. Register Your Sprayer Online @ www.chapinmfg.com
Questions?
Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin. Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?
No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
3. Filter
e lter helps prevent clogging while spraying. It is located on
the end of the outlet tube inside your sprayer tank.To clean lter,
remove the discharge assembly from the tank (Fig.1A, 3A). Make
sure the lter is positioned at the bottom of the tank as pictured
Filter
3A
Sk-1154-1
WARNING: Improper use or failure to follow instructions can result in explosive failure
causing serious eye or other injury. For safe use of this product you must read and follow all
instructions. Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up
resulting in possible explosion. Do not store or leave solution in tank after use. Always wear goggles,
gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use any tool to
remove pump if there is pressure in sprayer. Never stand with face or body over top of tank when
pumping or loosening pump to prevent ejecting pump assembly and/or solution from striking
and injuring you. Never pressurize sprayer by any means other than the original pump. Do not
attempt to modify this sprayer. Replace parts only with manufacturer’s original parts. Never spray
ammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat, pressure,
or gas producing chemicals. Always read and follow chemical manufacturer’s instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
4. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
Replace hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank
for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening
and could result in explosive bursting under pressure. If any of these signs are found, discard tank
immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20
strokes and inspect for leaks).
5) Do: Direct shut-o away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed
with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and ttings for rust, corrosion and pitting. If any of
these conditions are found, replace aected part with original manufacturer’s part before using.
1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling, Pressurizing and Spraying
Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed with water
after each use.
2) Do: Open shut-o and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
2. Nozzle
Attach nozzle to shut-o handle or extension wand.
1. Hose to Tank
Make sure white outlet tube
is attached to hose.
Insert tube into tank.
Proper placement of
white outlet tube.
Line up tabs on safety
lock connector with
notches on the outlet
ange of the tank. Insert
tabs into notches to form
a secure seal.
Slip hose nut down to
tank, turn clockwise
and tighten as tight as
possible by hand.
1A
1B
1C
1D
1E
2A 2B
Adjust spray pattern
by turning nozzle cap.
Do not turn cap more
than 2 turns or cap may
come o allowing spray
material to spray back
on you.
Do: Turn handle
clockwise to tighten.
Push handle down,
turn 1/4 turn
counterclockwise to
release.
Do: Pump until you
feel resistance.
Do: Push handle,
down, turn 1/4 turn
clockwise to lock. Begin
spraying. Re-pump
sprayer as required to
maintain spray force.
6B6A 6C 6D
10. Troubleshooting - Tank pressurizes but does not spray.
WARNING: Release pressure in tank before troubleshooting.
Clean Nozzle Assembly (Fig. 10E) -Remove nozzle cap by unscrewing. Clean and re-assemble.
Clean shut-off (Fig. 10A- 10D)
10E
Nozzle Cap
Pull handle straight
up.
Insert notches
from underside of
handle into plunger
grooves and turn
counterclockwise.
Tighten plunger clockwise until
ush to top of shut-o body. Do
not over-tighten or unit may not
spray. Slide forks under plunger,
push handle down until it snaps
into place.
10A
10B
Handle
10D
Plunger ush
with body
Remove plunger, diaphragm and
spring. Wash diaphragm with
mild detergent. Reassemble:
Hold shut-o upright as shown,
place spring in hole, place
diaphragm on top of spring.
Reassemble plunger and tighten.
10C
Plunger
Spring
Diaphragm
6-7749
Extension wand
Vara de extensión
Rallonge
6-4645
Pressure Relief
Valve
Válvula de descarga
de presión
Soupape de
décompression
6-6136
Hose
Manguera
Tuyau
6-4626
Shut-o Handle
Mango de cierre
Poignée du robinet
6-6003
Nozzle
Tobera
Buse
Nozzle Kit
Juego de boquillas
Kit de Buse
3-4852 (2658E)
3-4853 (2659E)
3-4854 (2660E)