Full Product Manual

6-4566
Four Position Nozzle
Boquilla de 4 posiciones
Buse à 4 positions
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious eye or other
injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized sprayer in the hot
sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or leave solution in tank after use. Always
wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use any tool to remove pump
if there is pressure in sprayer. Never stand with face or body over top of tank when pumping or loosening pump to prevent
ejecting pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original parts. Never spray
ammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat, pressure, or gas producing chemicals.
Always read and follow chemical manufacturer’s instructions before use with this sprayer as some chemicals may be
hazardous when used with this sprayer.
Sk-1154-1
WARNING
1. Hose to Tank
2. Nozzle / Extension Wand
Attach nozzle to shut-o handle or extension wand per Fig. 2A-2D
depending on the style of extension wand included with sprayer.
3. Filter
e lter helps prevent clogging while spraying. It is located on the end of the outlet tube inside your
sprayer tank.To clean lter, remove the discharge assembly from the tank (Fig.1A). Make sure the lter
is positioned at the bottom of the tank as pictured (Fig. 3A).
Note: Filters are not supplied with deck sprayers.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose before using.
Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of deterioration
of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in explosive bursting under pressure.
If any of these signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and inspect for leaks).
5) Do: Direct shut-o away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling, Pressurizing
and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and ttings for rust, corrosion and pitting. If any of these conditions are found,
replace aected part with original manufacturer’s part before using.
5. Pre-Use Check
6. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overll to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
8. To Release Pressure
Sprayers with no pressure release valve
Do: With pump facing away, turn locked handle counterclockwise until air begins
to escape. Stop turning handle when you hear air escaping. Do: Point pump away
until all air has escaped.
9. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling, Pressurizing and Spraying Instructions,
except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed with water after each use.
2) Do: Open shut-o and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions?
Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
015646-3 (A) R0318
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Discharge/ Tool Holder Assembly
• Insure the tool holder is assembled to the tank adapter before mounting the discharge assembly (Fig.1A).
e Tool Holder snaps into the groove of the tank adapter. Figure 1D shows how the shield and cup are mounted (Not all models are
provided with tool holder, spray shield and measuring cup).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1A).
• Firmly insert the outlet tube portion into the tank adapter (Fig. 1B) leaving no gap between the tank adapter and outlet
tube adapter. Firmly tighten the retaining nut to the tank adapter (Fig. 1C).
WARNING
To prevent hose from blowing o, hose must cover both barbs on the outlet tube adapter and touch ange
(Fig. 1B) before hose nut is securely tightened (Fig. 1C).
1A
1C
Retaining Nut -
Securely tightened.
Tool
Holder
Measuring
Cup
Spray
Shield
1D
Tool
Holder
Outlet
Tube
Discharge
Assembly
2A
Filter
3A
4. Shield Attachment to Wand
Snap shield onto wand as shown. Using the spray shield will help protect your plants etc. from
over spray. (Not all models are provided with spray shield).
4A
Parts, Piezas, Pièces
6-2001
Hose Kit: 2 nuts, 2 barbs
and hose
Juego de manguera: 2 tuercas
,2 lengüetas y manguera.
Nécessaire de tuyau: Deux
écrous, deux ardillons et tuyau
6-2000
Shut-o Handle
Mango de cierre
Poignée du robinet
6-5364
Measure Cup
Taza para medir
Tasse à mesurer
6-5385
Spray Shield
Pantalla de pulverización
Bouclier de pulvérisation
7. Pressurizing and Spraying
Do: Turn handle clock-
wise to tighten. Push
handle down, turn 1/4
turn counterclockwise
to release.
7A
Do: Push handle, down,
turn 1/4 turn clockwise to
lock. Begin spraying. Re-
pump sprayer as required
to maintain spray force.
7C
Do: Pump until you
feel resistance.
7B
Do: Turn end of nozzle to
adjust spray pattern.
7D
010842
Tool Holder
Soporte para la
herramienta
Porte-outils
1B
No Gap
Tank
Adapter
Outlet
Tube
Adapter
2 piece style
or
6-4645
6-3337
Straps
Tirantes
Sangles
6-6003
Nozzle
Boquilla
Buse
301120-4
Fan Nozzle
(brass tip)
Boquilla
Buse
3-4843
Fan Nozzle Pack
Paquete de boquilla a
chorro
Ensamble de buse à jet
éventail
Filter
Pull handle straight up. Insert notches from
underside of handle into
plunger grooves and turn
counterclockwise.
Tighten plunger clockwise until ush to top of shut-o body.
Do not over-tighten or unit may not spray. Slide forks under
plunger, push handle down until it snaps into place.
11. Troubleshooting - Tank pressurizes but does not spray.
11A 11B
Handle
11D
Plunger ush
with body
WARNING: Release pressure in tank before troubleshooting.
Clean Nozzle Assembly (Fig. 11E) -Remove nozzle cap by unscrewing. Clean and re-assemble.
Clean shut-off (Fig. 11A- 11D)
10. Fatigue-Free Spraying
For constant spraying, push down on shut-o handle and move grey locking mechanism
away from you. To release, squeeze handle and move the grey locking mechanism back
towards you. ( Not all models are provided with this feature).
2F
Red,
Fine spray for
ner washes
Blue,
Medium spray for
sealers
Yellow,
Course spray for semi-
transparent stains
Attach cap to shut-o handle or extension wand (Fig. 2F-2G).
8A
8B
2D
1 piece style
Deck Sprayers Only ( Fig. 2E-2G)
2E
Insert nozzle into cap (2E).
10A
2G
Locking
mechanism
Sprayers with pressure release/relief valve
Fig. 8A: Lift and hold the cap OR, turn the valve slowly counterclockwise until
air is completely exhausted.
Fig. 8B: Pull up stem until air is completely exhausted.
Fig. 8C: Pull ring out until air is completely exhausted.
Do: Point valve away from you when releasing pressure.
11E
Nozzle Cap
6-7756
Extension wand (brass)
Vara de extensión
Lance de rallonge
6-7749
Extension wand (poly)
Vara de extensión
Rallonge
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-1925
301272-1
Nozzle
(brass tip)
Boquilla
Buse
2B
2C
Remove plunger, diaphragm and
spring. Wash diaphragm with mild
detergent. Reassemble: Hold shut-o
upright as shown, place spring in hole,
place diaphragm on top of spring.
Reassemble plunger and tighten.
Plunger
Spring
Diaphragm
8C
or
Plunger
Body
Rubber
Diaphragm
Remove plunger. Wash diaphragm
in mild dish detergent.
11C
6-8156
Relief Valve
Válvula de descarga de presión
Soupape de décompression
6-8258 6-4648
WARNING: is product contains chemicals, including lead, known to
the state of California to cause birth defects and other reproductive harm.
Wash hands after handling.