Use and Care Manual

6-4566
Four Position Nozzle
Boquilla de 4 posiciones
Buse à 4 positions
1. Hose to Tank
2. Nozzle / Extension Wand
Attach nozzle to shut-off handle or extension wand per
Fig. 2A-2D depending on the style of extension wand
included with sprayer.
3. Filter
The filter helps prevent clogging while spraying. It is located on the end of the outlet tube
inside your sprayer tank.To clean filter, remove the discharge assembly from the tank (Fig.1A).
Make sure the filter is positioned at the bottom of the tank as pictured (Fig. 3A).
Note: Filters are not supplied with deck sprayers.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose before
using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of
deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in explosive
bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt to patch leaks,
etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and inspect
for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,
Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these conditions
are found, replace affected part with original manufacturer’s part before using.
5. Pre-Use Check
6. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
8. To Release Pressure
Sprayers with no pressure release valve
Do: With pump facing away, turn locked handle counterclockwise until air
begins to escape. Stop turning handle when you hear air escaping.
Do: Point pump away until all air has escaped.
015646R0322
Discharge/ Tool Holder Assembly
• Insure the tool holder is assembled to the tank adapter before mounting the discharge assembly (Fig.1A).
The Tool Holder snaps into the groove of the tank adapter. Figure 1D shows how the shield and cup are mounted
(Not all models are provided with tool holder, spray shield and measuring cup).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1A).
• Firmly insert the outlet tube portion into the tank adapter (Fig. 1B) leaving no gap between the tank adapter and outlet
tube adapter. Firmly tighten the retaining nut to the tank adapter (Fig. 1C).
To prevent hose from blowing off, hose must cover both barbs on the outlet tube adapter and
touch flange (Fig. 1B) before hose nut is securely tightened (Fig. 1C).
1A
1C
Retaining Nut -
Securely tightened.
Tool
Holder
Measuring
Cup
Spray
Shield
1D
Tool
Holder
Outlet
Tube
Dis-
charge
Assembly
2A
Filter
3A
4. Shield Attachment to Wand
Snap shield onto wand as shown. Using the spray shield will help protect your plants etc.
from over spray. (Not all models are provided with spray shield).
4A
Parts, Piezas, Pièces
6-2001
Hose Kit
Juego de manguera
Nécessaire de tuyau
6-5364
Measure Cup
Taza para medir
Tasse à mesurer
6-5385
Spray Shield
Pantalla de pulverización
Bouclier de pulvérisation
7. Pressurizing and Spraying
Do: Turn handle
clockwise to tighten.
Push handle down,
turn 1/4 turn counter-
clockwise to release.
7A
Do: Push handle, down,
turn 1/4 turn clockwise
to lock. Begin spraying.
Re-pump sprayer as
required to maintain
spray force.
7C
Do: Pump until you
feel resistance.
7B
Do: Turn end of nozzle
to adjust spray pattern.
7D
010842
Tool Holder
Soporte para la herramienta
Porte-outils
1B
No Gap
Tank
Adapter
Outlet
Tube
Adapt
-
er
2 piece style
or
6-3337
Straps
Tirantes
Sangles
6-6003
Nozzle
Boquilla
Buse
301120-4
Fan Nozzle
(brass tip)
Boquilla
Buse
3-4843
Fan Nozzle Pack
Paquete de boquilla a chorro
Ensamble de buse à jet éventail
Filter
11. Troubleshooting - Tank pressurizes but does not spray.
WARNING: Release pressure in tank before troubleshooting.
Clean shut-off (Fig. 11A- 11D)
10. Fatigue-Free Spraying
For constant spraying, push down on shut-off handle and move grey locking
mechanism away from you. To release, squeeze handle and move the grey locking
mechanism back towards you. ( Not all models are provided with this feature).
2F
Red,
Fine spray for
finer washes
Blue,
Medium spray for
sealers
Yellow,
Course spray for semi-
transparent stains
Attach cap to shut-off handle or extension wand (Fig. 2F-2G).
8A
8B
2D
1 piece style
Deck Sprayers Only (Fig. 2E-2G)
2E
Insert nozzle into cap (2E).
10A
2G
Locking
mechanism
Sprayers with pressure release/relief valve
Fig. 8A: Lift and hold the cap OR, turn the valve slowly counterclockwise
until air is completely exhausted.
Fig. 8B: Pull up stem until air is completely exhausted.
Fig. 8C: Pull ring out until air is completely exhausted.
Do: Point valve away from you when releasing pressure.
6-7756
Extension wand (brass)
Vara de extensión
Lance de rallonge
6-7 749
Extension wand (poly)
Vara de extensión
Rallonge
301272-1
Nozzle
(brass tip)
Boquilla
Buse
2B 2C
8C8C
6-46456-8156
Relief Valve
Válvula de descarga de presión
Soupape de décompression
6-8258 6-4648
Sk-1154-1
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious eye or
other injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized sprayer
in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or leave solution in tank
after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never
use any tool to remove pump if there is pressure in sprayer. Never stand with face or body over top of tank when
pumping or loosening pump to prevent ejecting pump assembly and/or solution from striking and injuring you. Never
pressurize sprayer by any means other than the original pump. Do not attempt to modify this sprayer. Replace parts
only with manufacturer’s original parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive
solutions or heat, pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s
instructions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING
6-2000
Shut-off Handle
Mango de cierre
Poignée du robinet
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
6-1925
Repair Kit (not included)
Juego de reparación (no incluido)
Kit de réparation (non inclus)
WARNING
Insert notches
from underside of
handle into plunger
grooves and turn
counterclockwise.
Tighten plunger clockwise until
flush to top of shut-off body.
Do not over-tighten or unit may
not spray. Slide forks under
plunger, push handle down
until it snaps into place.
11B
Pull handle
straight up.
11A
Handle
11D
Plunger flush
with body
Clean Nozzle Assembly (Fig. 11E)
Remove nozzle cap. Clean and re-assemble.
11E
Remove plunger, diaphragm
and spring. Wash diaphragm
with mild detergent.
Reassemble: Hold shut-off
upright as shown, place spring
in hole, place diaphragm on
top of spring. Reassemble
plunger and tighten.
11C
Plunger
Spring
Diaphragm
9. Care, Storage and Maintenance
1) Do: Follow chemical manufacture’s instructions for cleaning. Rinse thoroughly with recommended solvent.
Follow Filling, Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand
and nozzle are thoroughly rinsed after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.1-800-950-4458 www.chapinmfg.com