Use and Care Guide

6-6092
Hose Black
Manguera para trabajos
pesados Negro
Tuyau pour service
intense Noir
WARNING
Parts, Piezas, Pièces
6-6091
Hose Brown
Manguera Castaño
Tuyau Brun (1949)
6-6062
Shut-o Handle
Mango de cierre
Poignée du robinet
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-4629
1. Hose to Tank
2. Nozzle
Attach nozzle to shut-o handle or extension wand.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overll to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten
securely.
6-5943
Nozzle 1.0 GPM
Tobera
Buse
6-7703
Extension wand, Vara de extensión, Rallonge (1949)
6-7734
Extension wand, Vara de extensión, Rallonge (1979)
Congratulations!
You have just purchased a quality Chapin product. Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store. Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin. Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?
No regrese a la tienda; llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante: www.chapinmfg.com
Questions ?
Ne retournez pas au magasin. Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
015644-18 (A) R0318
6-5797
Nozzle .5GPM
Tobera
Buse
6-7745
Filtered outlet tube
Tubo de salida con ltro, Tube de sortie avec ltre (1979)
6-5373
Holster
Funda
Étui
7. To Release Pressure
1) Do: With pump facing away, turn locked handle counterclockwise until air begins to escape.
Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Sk-1154-1
WARNING: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions. Do not
leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original
parts. Never spray ammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of
tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank
weakening and could result in explosive bursting under pressure. If any of these signs are found, discard
tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20
strokes and inspect for leaks).
5) Do: Direct shut-o away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed
with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and ttings for rust, corrosion and pitting. If any of
these conditions are found, replace aected part with original manufacturer’s part before using.
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling, Pressurizing and
Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are
thoroughly rinsed with water after each use.
2) Do: Open shut-o and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening incover.
5. Pressurizing and Spraying
Lock
Position
TO LOCK HANDLE: Push handle down to
depress coil spring and turn handle 1/4 turn clock-
wise, then allow handle to raise into lock position.
5A 5B
TO LOCK PUMP: Place pump prongs
down into slots in funnel, turn clamp
clockwise to furthest position under
bottom slot, then turn handle clockwise
until tightly locked and sealed in place.
5C
For constant spraying, push down on shut-o handle
and move locking mechanism away from you. To release,
squeeze handle and move the locking mechanism back
towards you.
6. Fatigue-Free Spraying
6A
TO RELEASE HANDLE: Push down to depress coil spring and turn
handle counterclockwise 1/4 turn, then lift handle.
Pump until you feel resistance.
TO UNLOCK PUMP: Turn handle counterclockwise until 3-prong clamp
is loose. en rotate clamp counterclockwise to stop and lift out.
5D
5. Pressurizing and Spraying, continued
5E
5F
Attach the hose by screwing the swivel nut clockwise
and tightening to 37 in. lbs. Refer to Pre-use check
before using.